Everything You Need to Know about Sharkbite Fittings!

What are Sharkbites?
Sharkbite fittings are push-to-connects for plumbing fittings. Recently, many plumbers have gone from pulling out their solder torch and welding copper pipe together to pushing a SharkBite fitting onto a pipe. SharkBite fittings save time, they're easy to install, and they're reliable.
How do SharkBite fittings work?
SharkBites are simple to use. You push a tube into the fitting, far enough that it grabs a hold of the pipe. The O-ring seal inside creates a watertight seal.
Are SharkBite fittings reusable?
SharkBite fittings are reusable. Keep in mind that each time you use one on plastic pipe, the pipe may get scratched. If the scratches are deep enough, the pipe will bypass the seal inside of the fitting and create a leak. So yes, they're reusable, but reuse them with caution.
How do you install and disconnect a SharkBite fitting?
The installation is straightforward. Inside of a SharkBite fitting is a tube stiffener or an insert. If you're using PEX, make sure this insert is in the fitting when you push in the tubing. SharkBite offers a tool that deburrs the end of the pipe to ensure that your pipe is cut is even. If there's a sharp point on the end of the pipe, it could lacerate or take a chunk out of the O-ring seal.
What kind of tubing can SharkBite fittings be used with?
SharkBites are rated for CPVC and copper. These fittings work great with copper, whereas, some other push-to-connect fittings work better with plastic connections. SharkBite fittings also work with PEX tubing. When you use them with PEX, however, you need to use the tube stiffener because you don't want the fitting to give way because the tubing size flexes.
How can SharkBite fittings be used?
SharkBite fittings are most commonly used in household plumbing. The household plumbing fittings range from half-inch, three-quarter, inch and a quarter, and a little bigger. As long ask you're installing the fitting onto CPVC or PEX, you can use them for water anywhere in your plumbing system.
How long do SharkBite fittings last?
SharkBite fittings last a long time. In fact, SharkBite warrants the fittings for 25 years when used with SharkBite tubing.
Are SharkBite fittings supposed to spin?
SharkBite fittings will spin. The tubing is gripped by an O-ring seal. One of the benefits of SharkBite fittings is that you can put plumbing pieces together and rotate them into place to make the installation easier. You can rotate the fitting without any problems.
Rebecca and Jim Archetko
Archetko Homes Team
wefixitandwelistit.com
585.299.1112
We look forward to hearing from you!

[@lindamurrell9389]

69 year old woman been using these for years! I did not know about the little cramping tool which has saved my life! The little half circle thing made it too difficult to get off especially when under my house on my back with limited area to work with. Thank you for an excellent video!

[@AStanton1966]

I hear ya; those fittings are a BLEEP to remove. I bought those tongs, but still find it a pain, especially in tight areas.

[@fredbazoo]

I'm only an untrained Shmuck but arent you upposed to make a black marker line using a special gauge to mark how far the connection is?

[@23432]

That was almost everything I need to know. When should I replace these? Rubber rots, if these are inside walls I don't want to wait for extensive water damage because I can't monitor the joint.

[@chrisyndo4878]

I wanted to a slip extension applied. Not talked about

[@MrRainbowrooster]

Great video. Thank You!

[@AStanton1966]

Sharkbite recommends against removing those inner selves for copper. They say that it will damage the seal and make them unable to work for any do-overs.

[@bradwinfield835]

This video was depressing

[@AStanton1966]

You must be a plumber that gets $200 an hour.

[@cxgeokat4157]

Not so easy to use under a house. lol