excavator FAIL!!!! climbing on truck without ramps

this time it gone wrong :(

[@jix177]

The guy who never made a mistake never made anything. It takes a brave man to show his mistakes for the benefit of others. Well done for sharing.

[@barzdastato]

Thanks for suporting and for watching.

[@kalle8836]

That dosent mean u should make clearly stupid mistakes

[@jix177]

I don't think anyone said it does. But whatever.

[@tractorman6026]

Hey I'm a 20 yr operator, and I think you exercise one of the best qualities of operating. You were going slow and being cautious. You just messed up. Experience always wins. And I'm sure you know what you did wrong by now. Good luck man...God bless in Jesus name...

[@barzdastato]

Well said. Thanks for watching.

[@nemanjastojkovic7638]

The worst climbing i ve ever seen

[@Skyhawk-N7374ON]

Yeah, he tracked the wrong way.

[@mikeznel6048]

Blade goes first, set it on the bed of the truck. Spin around and push the machine up from the rear. Then you can crawl up without moving the truck.

[@roxkrasy8791]

Well somebody that knows what they're talking about,who would of thought. Blade up and drive it on

[@barzdastato]

Thanks for tips, but after this i dont try it again. thanks for watching.

[@mikeznel6048]

@@roxkrasy8791 There is many ways to do it but blade first is the best way for sure.

[@dannyc1657]

Yeah this fella was doomed from the very beginning 😂😂

[@IndependenceIron]

Even doing the blade first, when you boom down to lift the machine up, you also need to stick out so that you are pushing the excavator into the truck. If you only move the main boom the arc of the boom will start pulling the machine closer to the bucket(away from the truck) the lower the boom gets.

[@emclearance5694]

Machine cost about £15,000 . Ramps £150 .

[@marioreichl7647]

You are right with your point. But honestly these days alloy ramps for this wight cost about 400...500€.

[@emclearance5694]

I just sold £150. my very good pair of Ifor Williams Steel galvanized ramps each one was 3500kg so a safety weight of 7000kg . But New is £300 to £350 .

[@mikeznel6048]

Definitely it getting a set of ramps that will bring that excavator to the back of that truck for 150. Maybe 1500, used.

[@eric91780]

I often think about this seeing people doing this. It's like, what's the big deal with using some nice high quality aluminum ramps. All the time you spent lining it up and getting in and out the ramps would pay for themselves relatively quickly.

[@xxxmikeyjock]

come on over I will set you up with ramps and see how you fair in slippery conditions. the last thing you want to be is slipping sideways off ramps

[@bradh74]

I'm with the guy that commended you for showing your mishap. We use trailers in the USA for that, the no ramp method is dangerous for obvious reasons. Take care and be safe.

[@barzdastato]

Thanks for watching

[@xxxmikeyjock]

ramps are deadly. no way do I use a ramp for loading a machine in a trailer with bedsides

[@taki0ps230]

@@xxxmikeyjock ramps are deadly?? what?? you load a skid steer without ramps too???

[@xxxmikeyjock]

@@taki0ps230 I have a t740 and no where near enough skill to load it without ramps. I might try with a full bucket for ballast

[@xxxmikeyjock]

@@taki0ps230 the breakover when its slimy is scary A F

[@craigresterman9375]

Hey mate hope your head isn't too sore...you need to learn to use the track levers with your feet and always get the edge of the tray past the sprockets before you swing around also keep the door shut when doing this sort of thing because it adds support to the rops if you do crash and burn, happy digging

[@barzdastato]

Thanks for advice and for watching. I will never attempt this method again :D

[@treesquatch9150]

Nope get the proper equipment like the professionals get a trailer.

[@thylacine1962]

I guess its so easy to criticise some one who struggles with this manoeuvre. For some this is so easy & done multiple times a day. For others, pure stress. How ever you tried. Much more than many others. That's a +. Im sure by now you have mastered this gig. Well done. Forgive previous harsh comments.

[@barzdastato]

How i use to say: nobody born knowing everything. If you want to learn you have to try and from fails that you make on the way, you learn new things and abilties. Now worries all good. Thanks for watching.

[@thylacine1962]

@@barzdastato good luck with all future projects. Truth is you bravely have a go. That deserves respect. I hope your still operating. Rock on Bro.

[@danblackman2191]

So that's why you have a crane fitted to the truck so when you tip your machine over you can pick it up👍

[@barzdastato]

Exactly :D. Thanks for whatching.

[@danblackman2191]

Bet you have ramps now, bet that was very scary and lucky you were not badly injured... Be safe fella👍

[@Drummer81able]

Never climb up like that. Always have the blade as security behind you. I have done this with several types of machines over the years,and in Scandinavia this was s normal way to transport machines. This is a learning video of how you DOBT do it. Glad you are ok.

[@barzdastato]

Yes, hope others learn from this.. Thanks for watching.

[@Drummer81able]

@@barzdastato mainly...it's most important you are ok. All do mistakes,and i know many who have fallen off,tipped backwards etc etc.. especially in winthertime when it's anow and ice..i never liked it then.

[@williamturkewitschturkewit1549]

Dude now would be the time to change those hard to reach swing hoses..😅. Glad no one was hurt. I've seen this done a lot but can be dangerous especially if your lags are full of mud. I have a float for my excavator. Very easy and painless.

[@barzdastato]

Yes, need to stay positive (about hoses :D). Thanks for watching.

[@flightnavigator8999]

Yes please

[@morgansword]

I have loaded a lot of excavators this way, and it usually works well. We can't see what failed or why it failed. Anyone putting the blade in the bed first is the guy who will get hurt first. Not sure it would help to toss a old piece of plywood under the bucket so it would slide a bit easier or not. Most of those style excavators can lay on their side for a while and not trade places with engine oil for a good while if you get it back up again.. should still run fine and continue loading it. Pride gets hurt but really its just all in a days work

[@motionclone231]

seems like a good way to clean the mud out of the tracks

[@barzdastato]

True :D Thanks for whaching.

[@donaldgulledge729]

Just think of how much money you would have saved to have just bought a trailer. Just think of how much TIME you would save to load onto a trailer instead of this risky maneuver. I've seen people with too much confidence and bravado try this maneuver before (and yes most succeed most of the time) but I have NEVER seen anyone try to do this SOLO as the truck driver and equipment operator. That was twice the recipe for disaster. You shouldn't be surprised - sooner or later this was coming your way - its just statistics. I'm glad your ok, hope you learned more from this than simply trying again next time. Imagine doing this and having one of many hydraulic lines burst. Imagine doing this and having the truck brakes let go or the tires lose traction in the mud and start sliding. Imagine doing this and having a soft spot in the dirt cause one end of the blade to sink in. There is only about 100 things outside of your control that could go wrong even if your a top operator who does all your precise maneuvers right - then you put the icing on the cake by doing this alone solo getting in and out of the mini-ex over and over in odd positions. Don't mean to chew you out, but just get a dang trailer. Then you could haul your equipment and a load of dirt it dug at the same time.

[@barzdastato]

Yes you are right at all points. Peaple learn from their own mistakes, unfortunatly these mistakes are expensive. Thanks for watching

[@kiwidiesel]

Its hard to truly learn what not to do until you have done it, That's what experience is called and with that the ability to change your tactics next time, and bring spare pants lol. I have had my share of machinery scares. Even better when you can correct your own mistakes like you did and big shout out for making it public, I would have burned that video before anyone saw it lol. Well done with the seat belt, Everything else is what it is but without the seatbelt you may be in a very different result. Learn and move on from a nobody down in New Zealand.

[@barzdastato]

Thanks for watching.

[@michelsartorio7073]

Je suis désolé mais je n’est jamais vu monter une pelle comme ça artisan TP j’avais le même genre de matériel et vu comme tu fait acheter des rampes tu sera gagnant en sécurité surtout pour toi et tu sauras on ne descend jamais de la pelle et on monte direct dans la benne et on ne touche jamais au camion salut 👋

[@patho4908]

You learn from your mistakes just glad you wasn't hurt, it's just as easy using the ramps for safety reasons but if you don't put blade onto tray first

[@barzdastato]

Thanks for watching 😉

[@danfarris135]

Trailers, wonderful inventions they are.

[@barzdastato]

Yes indeed 😁. Thanks for whatching.

[@roxkrasy8791]

Keep ur chin up about most comments on here,harf the people here won't no how to drive a digger,the harf that do only think thay can drive a digger, but will be a small few that can operate an excavator and yes there's a big difference. I like the way u own what people are saying so ur on ur way maybe.blade frist next time a,on ya

[@barzdastato]

Thanks for suporting words. And thanks for watching.

[@Kasunderox]

You had to push the machine a little towards the truck and travel in a little before lifting the other end up. Or with a machine this big wi would usually load the blade side first. When you do that you can turn around and track further towards the truck without lifting the other end up from the ground.

[@barzdastato]

Thanks for advise and for watching.

[@mikeznel6048]

15:40 didn’t push out on the stick enough when you pushed down with the boom.

[@galewinds7696]

That's alright, just wear the bucket out scraping on the truck bed, we'll get a new one......

[@thegreat_I_am]

There are literally hundreds of videos on KZbin of people doing this successfully. I’ve never seen one of them raise the digger and then try and reverse the truck under it.

[@capnskiddies]

This was my thought exactly.

[@barzdastato]

kzbin.info/www/bejne/m4CoqauroKuIbdE

[@vonNachtmahr]

Interestingly, I see a lot of videos where the truck/trailer is always driven "under" the excavator when it is high. I would never do it that way. Either you can push up on the truck and reach the loading area with the blade and the undercarriage, which would have been possible without any problems in this case, or you leave it altogether and use loading ramps. Driving the vehicle back and forth is somehow wrong in all areas.

[@thegreat_I_am]

@@barzdastato So it can be done that way! Thank you.

[@royr3820]

I think he’s done this before because he came prepared with a crane and the funniest part of all, he put this on KZbin.

[@barzdastato]

Thanks for watching.

[@fanningconstruction2050]

No one believes in chocks until they snap a parking pawl and heart skips a beat and going on a ghost ride.

[@vaclavpolasek6379]

Better to spend a couple of bucks on ramps but hey, you win some, you lose some! Nice digger btw

[@barzdastato]

Learning from stupid mistakes :) Thanks for watching.

[@vaclavpolasek6379]

Crazy how the engine was still running😂

[@mikepage9520]

One of those things that's on the "can do it, but shouldn't" list

[@mewhoelse3554]

Lol. Rookie! That's how NOT to load an excavator! Lol

[@barzdastato]

Exactly, thanks for watching.

[@treesquatch9150]

Of you get ot on the truck how do you secure it?

[@barzdastato]

On that time i didnt secure it. Thanks for watching.

[@chenesplit9158]

Welcome with the jumpers !!👍🥴😉

[@anmoweb]

Never done it myself but those I'e seen done it got that iron bar in front and drive up, then sving the digger around and back up. You do not back the truck.

[@barzdastato]

Now i know that :D not the best may to find out, but its life. Thanks for watching

[@Emeric62]

I'm in France and every time i see small excavators like this they just put it in a dumpster then collect it with a roll-off truck

[@LoBeau53]

So you travelled the wrong way after all that set up?

[@barzdastato]

Yes closer to the earth :D Thanks for watching

[@mikeznel6048]

Glad you had your belt on man.

[@heath8779]

That’s 7.42 I’ll never get back, muppet, stick to loading ramps 🤠

[@MrJokkoma]

That mighty beard dampered the fall also besides the belt.

[@barzdastato]

:D maybe littlebit :D Thanks for whatching.

[@MrJokkoma]

@@barzdastato To be honest, it must be a quite tricky maneuver to load an excavator whit such short tracks on a regular truck.

[@barzdastato]

@@MrJokkoma yes it is...

[@АлексейБелов-и4ц]

Ума нет- считай колека, зачем руля крутил? Надо было сразу ровно к кузову подъезжать и при заезде ,,задним,, ходом на платформу рукоять одновременно с ковшом выворачивать. 2 основные ошибки.

[@barzdastato]

Спасибо за просмотр.

[@WP18_-_-]

Kauf dir Rampen dan ist der Bagger in 5 Minuten verladen und ohne Unfall.

[@excovatochic]

Бедная стрела 😱 нельзя так нахрапом ехать 🤦‍♂️

[@6920-n4d]

What damage did the excavator take tho, looks few thousand on repairs probably. 🤪Stay safe

[@barzdastato]

Actually fitted under one thousand, but it was dificult to find who can do such work. Thanks for watching.

[@6920-n4d]

@@barzdastato ooh i'm suprised. Knowing prices for parts for agricultural equipment that's actually pretty low. Sorry for english not my first language.

[@heelerhealer7552]

Track are clean and free of dirt now.

[@rickhay9782]

If you value your time at all, you could buy a trailer instead of trying to load in truck bed every time you came to job site.. Load then unload...time is money

[@barzdastato]

True, Thanks for watching

[@broyttube]

Just first look at the vid i see the mistake instantly NEVER have the blade on the back blade has too be infront ALLWAYS if u lose the Grip the blade will save u and also u will not make that big marks after u on the ground i know it is scary to swing when it's so high up but thats the best way just take it easy dont rush and make sure ur not too far out hope it went well whit the machine and u take care❤

[@barzdastato]

Yes it was rookie mistake...I will never again try this method :D. I get fixed machine and now it still working. Thanks for watching.

[@Andre-ng5ic]

It’s better with the blade the other way👍

[@barzdastato]

True. Thanks for watching.

[@cdsnider9496]

Dude... you had it!

[@barzdastato]

Yes almost 😁. Thanks for watching.

[@marsoudu87]

On buy 1500 dollars ramps, and you save money... you don't dammage your excaavtor and your truck And your life too

[@MiniexcavatorRostov]

Надо было и кран в конце перевернуть.

[@joe86johnson]

That's one way to clean the dust off your machine!

[@barzdastato]

Thanks for watching.

[@redeyedmongoose2963]

I believe it was WC Fields Who said a sucker is born every 10 seconds

[@IBRACIN]

Newbs on equipment thats what happens... glad you were not hurt.

[@barzdastato]

Thanks for watching

[@ericmaxwell4161]

Good thing he turned the motor off soon after the accident.

[@polarViking]

This is a operator fail, excavator is inocent.

[@skliros9235]

Good job!

[@Anthony-os8id]

Cheap excavator up for sale Just a few scratches 😅

[@koas8478]

That was awesome!

[@rodrigogomez5035]

#1 if your excavator has a blade, then load it forward, why? When it comes out, you will scrape if you unload it in reverse. #2 The tracks were long enough to reach the truck bed so why use the blade for leverage? #3 NEVER EVER EVER leave your machine unattended on a cautious situation like this. Backing up the truck was cringe watching. Always be in a machine when you get in a sticky situation to stop it ASAP or back away.

[@barzdastato]

Thanks for advises :)

[@TheUltimate65]

This load have ending better when you have use a machinetrailer, 🤔

[@barzdastato]

Yes, its true, now i have platform truck. much better :D Thanks for whatching.

[@TheUltimate65]

@@barzdastato so long you survive its all good..🤗

[@williamdonohue7470]

Sure am glad I use a Lowboy.

[@Tatra815s1]

Хорошо что сам жив😉

[@barzdastato]

ну да, не повезло. Спасибо за просмотр.

[@slidingdoor9055]

Should have shut the truck door. It's the little things.

[@harolddougherty4724]

Yeah. Him doing it backward.

[@fathersons8791]

Please make a ramps.

[@giuseppemarino1694]

Poteva andare peggio, pensa se rompeva la sponda del camion

[@oudonbail]

Blade first and youv got this , can be safer than ramps

[@barzdastato]

thanks for watcing

[@stormnr2]

Using ramps is faster and more safe.

[@barzdastato]

After that i bought ramps, but it was not safer. Its very slippery when tracks are wet or frost outside. Thanks for watching.

[@B16Afreak]

Problem was smal Bukett and soft ground...

[@sandys9791]

Lol. No. Absolutely was operator inexperience. This shit is easy for an experienced operator who knows how to use the boom/dipper and track foot pedals in unison. He needs to practice crawling up over logs and learn how to use boom/ dipper controls with your hands and track controls with your feet in unison and this becomes easy and safe even with a slippery truck deck.

[@serge9846]

Ačiū Dievui, kad gyvas!

[@barzdastato]

Pasisekė... 😅 Ačiū, kad žiūrite.

[@9Pivo]

And this is the reason i got my self a hooklift truck

[@barzdastato]

Yes, hooklift is a good thing. Thanks for watching.

[@genelund1705]

Don't need ramps just need a operator. You saw his qualifications first hand when he didn't even have enough sense to shut the machine off while it was on its side all the while

[@barzdastato]

Thanks for watching, next time when tip over, i for sure will know what to do.

[@vivianapalestro9331]

molto bravo anche come gruista

[@evak-spas5525]

Рукожоп, ждал когда он в конце ещё и кран положит )))

[@stanislavyur]

Потом на авито!не битый не крашенный)))

[@barzdastato]

привет, а как иначе 🤣🤣🤣 спасибо за просмотр.

[@Кирилл-щ8ф5х]

Норм, зодовку почистил...

[@jun2vlog]

Be careful my friend.god bless you.new subscribe.

[@barzdastato]

Thanks for watching and subscribe.

[@lucas_vd_laak]

Put the shuvle on the front 😉

[@vortex075]

Quem não tem as manhas não entra não sem a instrução de um profissional

[@oliverhill84]

Please don't come to my house

[@c50ge]

Fast forward to 5:52

[@snoopy81]

Lucky u alive, expensive experience!

[@gerardfarrell3135]

U should invest in brown trousers

[@barzdastato]

Thanks for watching

[@brianvassar2556]

Bro needs a trailer

[@Sibbe2560]

This guy should be send to jail for live…😂

[@barzdastato]

If you say so 😅 Thanks for watching

[@richardholmes9295]

Sure I've done it before, I'm not an idiot.

[@barzdastato]

Thanks for watching.

[@phuskarbek6834]

I po co to cofac babrać sie ramie dalej koparka na pake spych do gory max obrot i wjazd z podpartą łyzka to spora koparka to wjazd szybki i łatwy

[@aussieearthmoving392]

Annnnnnnnd thats what you get!!!

[@alessandropaolini802]

Così non l'avevo ancora visto, bravo

[@paulkivisto9060]

Really sad accident: (

[@barrettm8279]

Si dice che.."u nghiuritu du culu e più forte du terremuatu" cit. Vecchio saggio

[@ghallums]

Dude, buy a trailer!

[@TheS3fahrer]

engine out !!!!

[@noedesbarbosasilvajunior9623]

Inexperiente é fogo....

[@parceirodoagro2068]

Um piscar a mercadoria tá feita

[@stefanerler2467]

If you dont can Drive you must take ramps

[@barzdastato]

How you can know or you can if you dont try :) After this i bought ramps :) Thanks for watching.

[@maxmax3623]

You are crazy 😂

[@barzdastato]

Like in movie Mad max lol Thanks for watching

[@giannidifelice943]

Jai fatto un bel lavoro

[@mrfingers4737]

Do you know what lever a does? Well you better lever b.

[@barzdastato]

Thanks for watching

[@DanielAvilan-tirado7600]

I was biting my nails just watching lol

[@barzdastato]

It was like in slowmotion movie. Thanks for whatching.

[@davewilberforve3595]

I knew why of cleaning out the tracks

[@tdmjason]

No reason to move truck .

[@khahoang1438]

Tôi năm nay 70tuoi giờ mới thấy giống tôi ngày mới vào nghề

[@jameslindley924]

😝