Today's video is showing you how to make an exhaust bellows tool for about $12-14 and get it on the housing in a couple minutes rather than fighting with it for hours!
Пікірлер: 41
@djbolduc1049 Жыл бұрын
Adding to small cables to the screws on the washers makes it easy to retract the expansion anchor for removal
@TheModAddict4 жыл бұрын
What i would suggest is adding a string to each side.. like nylon twine and when you're ready to remove the tool just push it in slightly and pull the strings to draw the "ears" in
@PMPerformance4 жыл бұрын
thats actually a really solid tip! Genious! Thank you!
@TheModAddict4 жыл бұрын
@@PMPerformance i have my moments. 🤣
@daveg21996 ай бұрын
Just reverse the threaded rod and take it out of the expansion contraption and put a skinny magnet it up in there because it would just fall into the bottom of the bellows. Cool video!! Helps alot
@PMPerformance6 ай бұрын
Sounds like you are in a great position do that. When I recorded , it was on the fly. This is now like 4 yrs old. Hopefully this gave some creativity to you to adjust and make an updated video.
@daveg21996 ай бұрын
@@PMPerformance I’m sorry if that came across too straightforward. I didn’t mean to set you off. I should’ve used a softer tone. I was at work just a quick observation. I wasn’t being sarcastic.
@PMPerformance6 ай бұрын
@daveg2199 an, it’s all good. I get a lot of suggestions on this video how to do it better. It’s just that it’s after the fact. I ca t do it different now. I’d like to see all these suggestions turn into videos though to remind me of better solutions next time I need to do it
@scottstichberry2797 ай бұрын
This is much easier to do while you have the shift shaft out to replace the seals and bushings during the transom re-seal.
@PMPerformance7 ай бұрын
I’m sure it is easy for a full R&R. That was not the task though. Thats like saying it’s much easier to change your oil pan gasket with the motor out of your car.
@hellcattracearound2 жыл бұрын
Tried it with the string to release the spring tension at the toggle , Gives a good advantage got everything at Lowes for $ 8.21. Got to dark out to see will start again in the morning . I do not see this being possible without adding special tool or making one.
@PMPerformance2 жыл бұрын
It certainly makes life easier. Good luck and thanks for watching.
@floridagirl386 Жыл бұрын
Damn youre smart! Thanks
@brianhahne96233 ай бұрын
I would tie some fishing line onto that anchor then when you’re done you push and pull on the fishing line to suck your anchor handles back and you’re done
@PMPerformance3 ай бұрын
This was made quite a few years ago, but great idea for next time.
@knowyuhgrow4203 жыл бұрын
Thanks for sharing
@PMPerformance3 жыл бұрын
Glad you found this helpful and thanks for watching.
@mumbles552 Жыл бұрын
I bet if you unwind the rod from the wall anchor, the anchor will fall over and could be pulled straight out with a pair of long needle nose pliers.
@PMPerformance Жыл бұрын
It’s been years since I used this, but I do not think it would. It would be caught in the ribs. Possibly though, I just don’t remember from when I made this video.
@sevenhornets4 жыл бұрын
I have a winterizing tool for you. James knows about it. I can make you one and send up north..
@PMPerformance4 жыл бұрын
Please elaborate on this winterizing tool? I didnt know any special tools were needed for that.
@ltpenniss66914 жыл бұрын
@@PMPerformance It's a plate you attach to the gimbal sassy that is used to put antifreeze into the engine and manifolds and serves as a blankoff to keep it clean and no one can steal your outdrive as well.
@PMPerformance4 жыл бұрын
LT PENNISS so basically it’s like muffs that you pump coolant in there and flushes water out from there?
@floridagirl386 Жыл бұрын
Yes i watched someone do zipties too. That is what im gonna do & if it doesnt work for me then im making this
@PMPerformance Жыл бұрын
Good luck and thanks for watching
@ChainsawFPV Жыл бұрын
Zip ties is a great trick to getting the bellow seated on the second side!
@PMPerformance Жыл бұрын
@@ChainsawFPV agreed they can help greatly to fish them out
@floridagirl386 Жыл бұрын
@@ChainsawFPV zipties worked for me!!! First time doing bellows. Definitely was NOT fun.
@floridagirl386 Жыл бұрын
Duuuuuude the damn thing slipped off!!!! What the hell
@davidskov7428 Жыл бұрын
Damn you tore that out drive way down 😳😬
@PMPerformance Жыл бұрын
That’s how you do a bellows job. Lol
@davidskov7428 Жыл бұрын
Not me….. 😜I just battled one today … pulled the whole out drive as 1
@davidskov7428 Жыл бұрын
But anyways thanks for the video
@PMPerformance Жыл бұрын
@@davidskov7428 I don’t remember how I did this as the video is probably over 2 yrs old at this point, but there was other maintenance I did while I was in there, and it was my first time taking an outdrive off. If memory serves me, I replace some shift cables and trim sensors and some other lines and such when I was doing this. The bellows was not the main purpose o was in there.
@nategremore9162 Жыл бұрын
Unscrew the rod , and fish the wings out!
@PMPerformance Жыл бұрын
This is a few years since the install, but I do not think that would help as I would need to fish it out. The rod helps fish it out.
@aNuthaRedneck Жыл бұрын
@@PMPerformanceGod invented stick magnets for a reason...
@PMPerformance Жыл бұрын
@@aNuthaRedneck ok, so purchase another item instead of just doing what I did? Next time a thank you for the video would have sufficed. You are more than welcome to make your own video showing your updated best practices and suggestions. That is the joy of having an open form of posting videos.