Exhaust Repair To Save $1000's

In this video I show you how I replace the flex pipe on a car instead of replacing the entire convertor saving the customer thousands over an OEM convertor. -Enjoy!
If an SMA Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE: / southmainauto
CHECK OUT OUR "SMA SWAG" STORE! Go on Teespring and get your very own SMA merch!
teespring.com/stores/the-sma-...
If you don't like Patreon feel free to use the "PayPal Me" link: www.paypal.me/SouthMainAuto
The South Main Auto Amazon Store:
www.amazon.com/shop/southmain...
AES Wave Automotive Diagnostic Tools: www.aeswave.com/cart.php?m=af...
Thank you for all the continuing support!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.

[@OneTrueCat]

I'm not a professional welder, and in fact, have never welded anything, but I am an internet user, so I definitely feel qualified to tell you my welds are ten times better.

[@tmetito3535]

Lmfao

[@InsideOfMyOwnMind]

LMAO REEEEEEEEE!!

[@paulheitkemper1559]

Same. My first weld will totally outclass this nonsense, assuming I ever weld anything.

[@jeffreyhancock8831]

Ha! Nice! Smartass!!! Two thumbs up! I imagine you snickering while you typed that! Ha!

[@jamespfitz]

🤣

[@marathonfreak67]

I'd rather have a good mechanic with basic welding skills than a pro welder with basic mechanic skills. Unless I'm building bridges or skyscrapers. Thanks for sharing!

[@rimmersbryggeri]

Erics welding was very simular to the welds on my walker pars that are sitting right behind me so probably more than just good enough.

[@curtiss1979]

Cool story

[@rentcda]

All day long!

[@bonedaddy4670]

Your welding is paying the bills and keeping your customers smiling… expert status in my book!

[@25enyce]

Facts

[@localcrew]

The number one criteria I have for weld quality is “Did it work?” So if I’m the welding inspector and anyone asks - these welds pass with flying colors. 👍

[@DaddyBeanDaddyBean]

My welds would be just as smooth and glossy as a bead of JB Weld, at least in part because I don't own a welder, and I do have some JB Weld.

[@coreybenson3122]

I’m god dang Journeyman JB Welder myself.

[@DaddyBeanDaddyBean]

@@coreybenson3122 I have a kitchen knife with a 100% JBW handle. It started out as a repair, replacing a chunk of one scale that cracked and fell off, but one thing led to another and now the original scales are completely gone, replaced with filed, sanded, and lacquered JBW. 😁

[@georgeburns7251]

Love these JB comments

[@edwardhalpin7503]

I've witnessed some JB weld magic but will it hold up in exhaust systems?

[@DaddyBeanDaddyBean]

@@edwardhalpin7503 sure. As long as you don't start the engine. 😁

[@Bryanbobber]

My entire business is just Automotive Exhaust here in NH. So finally seeing you do one makes it even more special! Keep up the awesome videos.

[@Daveez234]

Hey I’m from NH!!! what’s the name of the shop?

[@hurricaneatp]

Bryan!! What’s going on! We still get on the 4x4s to break some trails! 🤣

[@crbourret]

I'm in NH too!

[@Garth2011]

Are muffler shops still using torch welding or mostly using mig?

[@jamram9924]

I was out visiting my daughter from SW AZ. Stopped by a Napa Auto in Nashua, NH. I was flabbergasted by the amount of mufflers and exhaust pipes they carried. Y’all take the rust and I’ll keep the heat….😁. God bless..

[@BWDuty605]

"I'm not sure what engine it is" *in my head* "but it's big" "It's a little guy" Mind blown

[@macthammer]

I've been a professional welder for over 110 years now, and I still learned something from you today. Thank you. ;)

[@vivillager]

Normally when someone takes a rip saw to an exhaust system, it's to steal the converter, not the flexi-pipe

[@umajunkcollector]

That's in LA ci?

[@ebutuoyebutouy]

They also doing it in Houston. Sad.

[@tjoelfoster]

@@umajunkcollector Everywhere. They''ve been doing it in SC for years. Comes in spurts. I think a lot of it is a crew that roams the southeast.

[@kay110]

@@umajunkcollector They are stealing Cats everywhere in the world these days.

[@SiliconSentry]

@@umajunkcollector Had a crew hitting dealerships late at night in MN where my family is.

[@psycho-nutkase9233]

I duno , I had my flex pipe on my Celica done at professional exhaust shop and I can definitely say Mr O that you did a better job.

[@spelunkerd]

Nice job! This kind of thing, where an OEM part is bundled together with a money making part, happens all the time. I'd like to give them the benefit of the doubt, but we're way beyond that. They do it so the dealer can make money off their loyal customers, raising the cost of repairs so buying a new car is more attractive.

[@TwoTall1988]

In this case, having the flex pipe separate from the cat would introduce another flange to fail and another seal to start leaking. These flex pipes have been on the market for a long time and are an adequate repair. The only people that fall victim to the 'money making part' are ones that only go to dealers or technicians that charge markups on parts.

[@russellstephan6844]

There's other things to consider too on parts engineering such as manufacturing assembly costs and off-the-self components. An extra join may not seem like a big investment. But, what's the trade-off of the total life of the component vs. initial cost? I have a 30 year old pickup truck which has seen a ton of in-depth complete sub-system refreshes -- total from frame out front end replacement, everything downstream of the brake master cylinder, and a host of other systems... No one would keep such a vehicle if paying full retail to maintain it. But, DIY, it's a lot cheaper for me than buying a new truck. Designing and building a vehicle to last more than 15 years is false economy in this fickle consumer demand focused market. People neglect, abuse, and get tired of their possessions far faster and want new. It's their money, they can waste it however they want. The OEMs design to that lifecycle period and no more. I don't mind... This allows me to pick up rather serviceable used vehicles for a song, dance, and a couple of days of being on my back under the thing making it bulletproof reliable.

[@edwardhalpin7503]

Russell youre singing my song. I'm 59 years old and still learning

[@jkbrown5496]

I ran into that with the secondary air on my 2011 Tundra. Toyota's "fix" was to replace both solenoids and the pump, at least, not sure of the piping. They only sold the solenoids as a unit with the manifold. A bigger job than popping out 4 torx screws for the solenoid. In the end, all it needed was a bit of brake clean to shine up the solenoid cavity/valve and the reed valve. Thousands at the dealer vs half hour of my time for a fix in the driveway

[@russellstephan6844]

@@edwardhalpin7503 Yep. I'm a year behind you and still tackling new skills and techniques to fix vehicles and accomplish home renovations and repairs on my own. The savings and self-reliance are going to be a big positive as inflation gets worse and runs long... That previous 30 years of free money has a cost and the bill coming due will be here for a good long while.

[@markhoffman4903]

Oh I love how you pre hate the haters! Makes me giggle every time ☺️

[@IgorD33]

You are a good human being. Wish I had a mechanic like you here in Canada

[@shahsmerdis]

Me 2 here in NYC

[@TheZadMangat]

Come to Premium Auto Repair! I'm Brampton

[@TheZadMangat]

Best mechanic hands down!

[@JorgeRodriguez-po7kx]

In my Country too ! 😁

[@rreveler6705]

Safety squints replaced by safety brim there on the tack welds.

[@Mork007]

Great video Eric. Saving the customer money by not allowing manufacturers to bilk them on poorly designed overprices parts says much about your character. I applaud you sir.

[@WreckDiver99]

I'm no welder, and I didn't stay at a Holiday Inn Express last night...Looks like your skills are EXACTLY where they need to be...it fixed the car, and saved them money, and made you some money.

[@JohnG6]

I remember growing up in NJ in the 80's my dad found the perfect size can (dont know what of) to fix his exhaust (he drove an '81 Mercury Bobcat / Ford Pinto). I think by the time he got rid of the car the exhaust was nothing but metal cans and hose clamps.

[@leighpike6572]

Did that myself back in the eighties,....just a patch until I could afford a new exhaust.... it was still there years later when the car was scrapped

[@davimel4051]

Did that here in the UK on many cars. Heinz Baked Bean cans were my personal favourite. Beans on toast for lunch followed by a 10 minute cut, wrap and weld and hey presto, fixed exhaust!

[@jamesu]

It is only temporary, unless it works!

[@maciejolejniczak151]

Was Your dad name Macgyver :-))

[@SmittySmithsonite]

Been there - had soup and beer cans on the glasspack, all held up by wire coat hangers on my '85 Monte in the day, lol. WOOOBAAAAAAH!! 😬🤘

[@WatchWesWork]

Hey Mr. O, it looks like you welded that completely wrong. Can you please explain why?

[@markh.6687]

Hahahahahaha....NO!

[@TomE74]

Mr O for bonus points explain why we should use clamps too ... Oh hey Wes

[@buckeyejim2989]

😂🤣

[@hawkins19601]

yeah he welded it upside down. how can someone do that.hehehehe.

[@localcrew]

It’s an absolute travesty, I tells ya! He needs to get certified! Me - I’m just certifiable.

[@Robalo-2660]

Eric "The Welder"! You done good . A very nice stitch weld on some thin wall tubing in a confined space and you didn't burn through. Excellent!

[@Soothsayer-rs5nb]

Look out another welder weenie !

[@Dave-ty2qp]

I have to agree with you Robalo, but the cutting process could use a little improvement. LOL

[@jonathan1427]

Overhead, vertical

[@jongerber3476]

you tube ! Home of every armchair quarterback in the world . You do a fine job sir . Nice attitude and easy to watch .

[@peterlevy7679]

Most repair shops would just make customer buy OEM part you saved them a fortune, great job again.

[@mayorwrenchmcgnome]

I'm not a professional welder but I did stay at a holiday Inn express last night. LOL you did a fine job on that.

[@paulboomer7109]

I'm retired welding 40 years structural pipe up hand down hand learn to control the heat and the puddle starts and stops are important ! Your welding is just fine neat looks you got penetration good job. 😁

[@OldManBadly]

This is the sort of repair that makes you everyone's favorite mechanic. You saved the customer a ton of money, and by using a proper flex, you made a repair that will likely outlive the rest of the exhaust system. I know why you have plenty of return customers!

[@motivatedpeon]

As a professional non-welder I can reassure, that these welds do, indeed, look awesome. Also, as a strictly non professional car driver, I appreciciate this repair very much. I reckon, most shops would just have billed a complete new exhaust front to back :(

[@steveo6631]

A wise man once said - "A grinder and paint makes me the welder I ain't".... Anyway, who doesn't like saving money???? Well done, Dr. O.....

[@halbud]

And Confucious said "man who go to bed with itchy butt, wake up with smelly fingers" !! Confucious said it i didn't !

[@garykirk1968]

Da bigger da gob, da betta da job!!

[@mattl6300]

I was going to comment this but you beat me to it. Well played

[@misterhat5823]

AvE is a wise man now?

[@mattl6300]

@@misterhat5823 indeed. "keep your d!ck in a vise" AVE.

[@vehcor]

I no longer feel special. I thought all the KZbin welding "experts" were only following my channel! lol

[@johanreibestein4231]

in the pile hahaha

[@joejago5231]

Vehcor is in the house

[@jerrellstrawn6409]

Quit loafing and get your ass back to work.

[@45AMT]

Your work has been crash tested and passed. You're good...

[@joshlujan3318]

You don't have a gnome for that?

[@jerrycann6374]

They make those parts that combine multiple parts for assembly plant to lower production time and it's nice to see people like you who live in the real world and replace only what is needed.

[@nothingspecial3517]

Awesome that you fixed it instead of selling them a new converter, your repair looks better than the stock piece, every time you pulled the trigger on the welder I caught myself looking away thinking I would burn my eyes 😂

[@ansv3340]

Popular among mechanics who works on Chevy, if your truck/ van won;t start you need a new OEM , CAT, from a dealer )) then when new cats don’t fix they say they cannot fix the truck ,, and poor guy have to tow it to some local small shop, who finds that problem is simply a dead fuel pump, ..

[@jdelbrid]

Eric O. showing off his classic, head-tilt-tac, skills. 💪👍

[@kirkfranks1]

Saying a prayer for each tack weld

[@n9wox]

Safety 2nd.

[@jacmccauley7581]

Great fix Eric. Bet that customer was happy not having to buy a new converter

[@frbrbrgrblgrr7777]

Everyone’s a pro welder, soldier and doctor on KZbin

[@David-bs6bv]

Something about the sound of a mig welder with the proper settings is so satisfying to me.

[@CrimeVid]

Takes me back to the first car repair I was ever involved with, splicing a bit of helical flexi into my dad’s pre war Rover14 about 55 years ago ! Dad said I could get under the car easier ! It’s nice to see people are still saving money.

[@larrymunday7519]

I used to do that with a torch and coat hanger, great job Eric!

[@joejago5231]

i still use a torch and coat hanger and i got a new mig

[@gonesideways6621]

Welded steel rule dies many time with coat hanger.

[@1keykneedeep]

Great job Eric. U saved the customer big $$$$. They wont soon forget it.

[@rayd.5088]

Great job! That's exactly what I would have done. I'm a retired technician of 40 years and have pretty much seen it all.

[@tambourine36]

Can u give me your expert opinion on something perplexing me please? Had to replace muffler and flex pipe after 3 rear end hits to my KIA Sportage 2.4 L EX 2011. No one would listen that the exhaust parts after the hits caused noises and vibration. The a/c compressor also failed and they told me there was a leak and an electrical issue that caused it to fail. Could the rear end hits that caused the exhaust stuff (flex pipe) have wrecked the compressor because of the heat from broken flex ? Could it have melted the wires or the hoses to a/c or rattled the components of a/c to cause it to break down? Need to find out before I make another repair? Would appreciate your expertise. Thanks.

[@rayd.5088]

@@tambourine36 Yes a broken flex pipe would definitely make exhaust noise and depending on the severity of the leak, and it could damage any nearby wires or hoses, I'm not so sure about A/C compressor damage. Possibly the compressor clutch wiring causing no compressor engagement and hoses causing refrigerant to leak out. Was there an insurance claim? It could be covered from accident repair claim. Hope this helps.

[@hvacr24]

excellent work EO!! another great money saving video by SMA

[@simonthegreat543]

“Wat do you want me to do, chop it off !?!” Makes me chuckle. Currently enjoying a coffee from my SMA mug. Cheers and best wishes from the UK.

[@alward9901]

We used to say if you can pee you can paint . But welding a lot different . Learning & practice and advice from a pro .you did fine Eric 🇺🇸👍

[@JohnnieBravo1]

Mr. O!!! What did you forget we always look forward to??? "Hey there Viewers!! Welcome to South Main Auto!!"

[@davedeatherage4902]

Great video for us who've not a lot of Automotive experience, .... thank you sir!✔️👌👍🏻🇺🇲

[@Paul1958R]

Eric, Great video and fix - thank you! Paul (in MA)

[@thefretfiend]

The beauty of a MIG welder. It makes welders out of all of us.

[@poorboyman5565]

Does it work? Yes. Does it leak or make noise? No. Job done! Good job Eric.

[@basshunter428]

You welded, it helded.👍 I used the same flex coupling on my 98 Wrangler to absorb the engine torque rock (4.0L TJs are notorious for cracking the exhaust header). That was 2yrs ago and it works great.

[@kalkhoven89]

Keep up your great videos Eric!!

[@williamdyckman9704]

Eric, saved that lady a ton of money, and I learned how to fix it !! Thank You !

[@petesandy5015]

I am a Professional Boilermaker here in Australia and have been for 55 years cant see narda wrong with these welds and ya welding the worst stuff on the planet... EXHAUST TUBE !!!! Good Job .

[@k4x4map46]

loving the prayer before each tack weld!!

[@davidkroth]

This has motivated me to get out there and fix my own exhaust, which is leaking a little lately.

[@kevincampbell8298]

As me grandmother would say A blind man would be happy to see it! It holds. Doesn’t leak. Good enough.

[@henryg683]

Eric O you were a life saver on this job!!!!! Say hey to MRS O!!!!!!

[@zorans5200]

You did great work my friend! When in doubt with welding thin tubing, just do conjoined tacks all around the tubing.. it's much easier then trying to blast a bead all the way around and burning thru it.. I had to repair many exhuasts aswell in my day lol.

[@williamperry118]

Your amps and wire speed are spot on. Supposed to sound like frying bacon 🥓 👍

[@DaddyBeanDaddyBean]

"If your welds SOUND like frying bacon, you're doing just fine. But if your welds SMELL like frying bacon, partner, you're on fire!" -AvE

[@Phantom-mk4kp]

@@DaddyBeanDaddyBean sounded like pulsed to me but I could be wrong

[@Kevin-zo6nz]

@@Phantom-mk4kp pulsed? Everytime he layed a bead it was constant wire feed. My friend also taught me to weld with the Bacon frying statement, something I wont forget

[@Phantom-mk4kp]

@@Kevin-zo6nz Pulsed MIG does not vary the wire speed it varies current wave form. So you wouldn't hear the feed vary

[@Kevin-zo6nz]

@@Phantom-mk4kp over my head, I just point and shoot my mig lol

[@davethornewell7417]

As you said, you aren't a professional welder, I have seen much worse by professionals and automated welders, yours is functional and presentable. I'm sure the customer is happy with the results, especially as they have saved a lot of money, unless they put the car on a ramp, or got ran over by it, no one is going to see the repair anyway. Certainly with 47 years experience in the motor trade, I have rarely seen anyone attempt to repair an exhaust, usually choosing the easy option to fit new, then question their logic when bolts start snapping off or seize. Good job.

[@RenegadesGarage]

South Main Auto.. Awesome job bro. And I thought I was the only one that had the KZbin "experts" commenting on my videos...

[@miguelare3]

Idk those welds look pretty damn good to me Eric!

[@martinblank4250]

Perfect timing! Thank you very much!!

[@jaredstrehlein5605]

Auto mechanics know how to weld. Welding is the sign of a true auto mechanic. Some mechanics are parts changers, and others can fabricate. To fabricate a person must know some small basics of welding.

[@HansPD]

Everytime a new video comes out from Eric O, I press "Like" , then I watch it!

[@NoNonsenseKnowHow]

Nice repair! Now if only they would make aftermarket flex pipes that last a little bit longer. I've had a pretty bad experience with those Walker pipes. A year or two later and they're rusted through. Here in Pennsylvania

[@RepairRenovateRenew]

Road salt is no joke. They don't call it the rust belt for nothing

[@mattatat1138]

They're in the business of selling you pipes to fix old rusty junk, if you get two years out of them you're probably doing great 😂

[@lilpandasdancin]

@@RepairRenovateRenew road salt looks at your car like its a whole thanksgiving dinner and it weighs 600lbs

[@ansv3340]

Why that spot needs a flex pipe? Go with piece of good quality solid pipe and forget about your exhaust, ,, if you find one in stainless steel will be even better, . Older pickups and vans did not have any flex pipes or harmonics,

[@nickmiller3764]

@@mattatat1138 2 years = 20k miles. They should def hold up way longer than 20-24k miles

[@joebuckley9940]

Nice clean job, saved the client a ton!

[@sunsetoriginals7320]

I’ve never seen a 3 year old car need exhaust work before! Great work FORD!

[@jaywattman199]

Eric O just an honest mechanic helping his customers get back on the road. That's why I enjoy watching his videos! No one is perfect at everything. Isn't that why we come to youtube to learn?

[@Wolf-uy9xo]

I've watched alot of your videos and your number 1 is always looking out for the customer. You run a great shop let the haters hate.

[@nainnub1]

Let them go watch Pelosers vids

[@jeffpuras7501]

Great job! (Retired actual pro) Nothing more fun than welding rust. Well…….gas tanks too.

[@deanmckee1385]

Doesn't leak, Doesn't fall off, that's a pretty good welder in my book👍Thanks Mr O

[@danhnguyen-fn9eb]

Nothing wrong with repairs like this. The legal stuff is still there and the stuff for engine performance and you save the customer many $$$$$$$! Unfortunately there are times you have to bite the bullet and pay the big bucks but this wasn't one of them. Good job.

[@gordonrichardson2972]

I've just been binge watching the I C Weld channel, that guy is an artist with heavy metal...

[@charlescastillo8870]

Very humble man who always claims he's still learning . He always says this may not be the correct way to do it but this is how I do it

[@zeroyon4562]

Cutting edge engineering is a good watch too.

[@Troy_Built]

The last time I welded exhaust it started resembling a porcupine before I was done. Yours looks pretty good to me.

[@fngonuts]

Same here.

[@brianmason8400]

I third that

[@tomlewis3658]

This came up on my feed immediately after I watched Ivan of PHAD working on the worst wiring in the world - an engine-swapped Audi A4. So I saw a pair of skilled surgeons saving cars - Dr. Ivan, MD, PHAD, fixing shattered nerves, and Dr. Eric, MD, SMA, replacing a failed section of the EcoSport's digestive system. Well done, doctors!

[@cLEdits]

Always looking out for the customer. I’m a residential service plumber. Same selling points, saves the customer money and hassle. That’s why we do what we do brother. Class act.

[@joer9276]

That’s a 2018, holy crap! Good job!

[@michaelowen1750]

As a former professional welder- I'd say you did the perfect welds...get the customer out the door with minimal cost.. they'll be back for brakes

[@michaeltexeira6185]

Good business idea. Not the rip off Dealers. They have now. 🇨🇦🇨🇦

[@BrianAhearn8597]

Is that mig welding?

[@45AMT]

At the end of the day. It works no leaks who cares what the welds look like it's under a car. Good job Eric!

[@jonminer9891]

Hi, Mr. O. Best under-car welding I have ever seen. Thanks for sharing! Stay Healthy!

[@DAKOTANSHELBY]

Great work Eric! As a past Tech Advisor for Jeep in the 90s, I resolved Grand Cherokee exhaust drone noise complaints by installing those flex pipes. They also come in varying durometer selections. Thanks for all you do!

[@jimr549]

Actually that would have been covered under the emissions warranty. Had the exact same thing happen to my Sable years ago and since the flex pipe was part of the converter it was covered. Should be 8/80 on anything emission related.

[@dans_Learning_Curve]

8 years or 80,000 miles?

[@memyselfandi3925]

Rust damage isnt covered. Rust states have this issue often

[@jimr549]

@@dans_Learning_Curve Yes. It didn't break off like that one but the braided part covering the spring came off so it was loud.

[@markdiesel6843]

Very nice thanks for saving the customer a catalist expense your a good mechanic that values his customers

[@alantorrance6153]

Another great learning experience. Thanks, Eric! Just added another technique to my inventory.

[@viatronmac]

My professional welder here in Sri Lanka who welds using a car battery whilst wearing flip flops and sunglasses says you did that wrong………😂😜

[@chriscrusader5412]

You're freaking awesome, I would let you weld my stuff any day!

[@timwall6916]

Yea and you Mr.O can even weld Chris Fitzpatricks pipe whenever you like 👍

[@GeminiSeven43]

Awesome Job and saved the customer tons. You are a great inspiration for going above and beyond for your customers.

[@stevetheriault4164]

HEY MR O nice to see there's still good honest mechanics ,,nice work you saved him lots of money GODBLESS

[@danmolumby4186]

When the master welders become a better mechanic then you, then they can complain about your welding. I think you do an amazing job! Keep up the great work and videos. 😊😊

[@jaccoonderdijk1777]

"Just like real life, it's a little bit to short!" Can i get an Amen?!

[@malcolmyoung7866]

As a ‘professional’ KZbin commentator and observer I can say with great authority that I know less than Eric on just about every thing mechanical/electrical and welderical… to that end I doth my cap in acknowledgment of the great guru who fixes rust boxes ‘ad finitum’ and continue to learn that my efforts to gain knowledge regards the above is not wasted… I have even burnt some holes in some steel and blown some fuses along the way… and bought tools… lots of tools that one I may actually use ….

[@PRO4XKEV]

Fantastic repair, you saved the customer money, customer has money now to come back for maybe some other future work.

[@GoatOffroad]

I am just learning how to weld and I love it! We joke around and instead of me laying dimes I say “ I’m laying worms” 🤣. Cuz they sure look a lot like worms when I’m done laying a bead. Lots more practice for me!

[@MrRlspell]

I friend once told me my welds would improve after I ran a couple of hundred pounds of rod. He was right.

[@dougtexas]

Nice work, Eric! Saved that customer some serious $$. However, with the absence of brake cleaner and ugga dugga's it's a 9 out of 10. 🤣🤣🤣

[@michaeltexeira6185]

What is a Ugga duggas just curious. And the brake cleaner have to do with welding,,

[@dougtexas]

@@michaeltexeira6185 ugga duggas is a scientific method Eric utilizes to apply an exact amount of force. One ugga dugga, two ugga duggas, etc. Brakleen is a fan favorite due to Eric's varied uses and the sounds used to present it. For lots of us, the best videos include ugga duggas, Brakleen, Big Nasty, and lots of innuendo from Eric. I refer you to some of the tougher jobs he has had to accomplish.

[@hondatrix]

Was so good to meet you guys...... stay safe and hard working!

[@rogergoins8118]

Doesn’t matter what it looks like as long as it gets the job done. Nobody will see it anyway. Great job!

[@pootthatbak2578]

I thought, when you had those safety glasses on during the intro, you were looking like a younger bob villa from this old house show

[@Jacksonkellyfreak]

I've always thought your welds were great.

[@TheSleepingonit]

I use furnace cement for exhaust leaks. Feather over the hole when it's cold, let it sit a hour and drive until warm. JB weld burns at 300, furnace cement melts at 2300

[@SpynCycle57]

Back in the 1970's, when I was a broke teenager, my car had a loose exhaust pipe connection, where two pipes met. I went to several shops asking them to weld it. They all said I needed the pipes replaced, which I couldn't afford to pay for. So I gave up and pulled a tin can out of the trash, cut the bottom out, and slipped it over the connection. Clamped both ends and went on my way. About once a year I had to replace the tin can, which was no big deal.

[@brianmeek5236]

Looks great, I’m so embarrassed by my welding job on my old Denali I can’t take it to a garage anymore

[@markh.6687]

"Oh, I'm a welder and I'm okay; I sleep all night and I work all day!...."

[@ferrumignis]

I grind my welds, I paint 'em up They look pretty as can be. If they fail I don't care, You can't prove it was me.

[@peterallen4331]

But do you wear suspenders & a bra ?

[@markh.6687]

@@peterallen4331 "I weld exhaust pipes; I skip and jump, I like to press wild flowers!...."

[@blower1]

@@markh.6687 I put on women's clothing and hang around in bars!

[@stevebot]

Many of my best friends are welders and only a few of them are transvestites.

[@yhird]

Pro work Eric! Fantastic job. Cheers.

[@stantilton2191]

A fine fix young fella. Exactly the kind of thing i would do for my rig. Thank you.