That's amazing. Taking such deep cuts in one pass.
@SienciLabs6 ай бұрын
It was absolutely impressive for sure! It's a powerhouse!
@jimsk9s6 ай бұрын
Very excited to get my hands on one of these!
@SienciLabs6 ай бұрын
we're thrilled to hear that! 🙌
@ifiwooddesigns6 ай бұрын
So in love with that machine.
@SienciLabs6 ай бұрын
We're happy to hear that! We think it's pretty amazing too! 🙌
@darrylcameron89656 ай бұрын
Can't wait to get an AltMill! Was just about to get a LongMill but I have to wait for this now.
@SienciLabs6 ай бұрын
Or both! 🤷♂️😂
@darrylcameron89656 ай бұрын
@@SienciLabs I wish my wallet was big enough ;)
@stuartgrimm60486 ай бұрын
Geez Andy. Couldn’t find a bigger adjustable wrench to tighten the collet with? You must have been struggling with that tiny one. 😅
@SienciLabs6 ай бұрын
we did have a bigger one, but it just seemed overkill 😉😝
@about2acres8244 ай бұрын
Would be cool to take that and make a table out of it by framing it and pouring epoxy.
@SienciLabs4 ай бұрын
🤔...Got us thinking now
@alassafcam6 ай бұрын
Magnificent work
@SienciLabs6 ай бұрын
Well thank you ☺️
@Parker99200123 күн бұрын
Why no roughing pass?
@drkline696 ай бұрын
Very nice but I would have gone with a much smaller stepover to reduce the bit lines. Would take longer but would end up with a much smoother finish and better detail.
@silvansilva89396 ай бұрын
Sim, mas esse tamanho é mais fácil de lixar
@BuckysCustoms6 ай бұрын
A Thing of Beauty!
@SienciLabs6 ай бұрын
You got that right sir!
@doughoiby81956 ай бұрын
Just an FYI... Stepover should be 0.029" for the Tapered Ball Nose. But very cool project!
@SienciLabs6 ай бұрын
Yup 🤦🏻♂️...Good catch. I (Scott) missed that one 🤦🏻♂️...
@doughoiby81956 ай бұрын
@@SienciLabs No worries... Seemed like a quite large stepover for such a skinny but... Lol
@2ninga6 ай бұрын
That looks to be what he's running. On hardwood it should be a little tighter than that, even with that size carve. I wouldn't run the TBN any larger than 0.15mm unless it was a clearing tool path. If you're choosing to carve a masterpiece design, it's not worth cutting corners, ....just the cusps ;)
@silvansilva89396 ай бұрын
Incrivel, que liquido é esse que foi despejado na arte ?
@silvansilva89396 ай бұрын
Is that mineral oil that you applied to the art?
@SienciLabs6 ай бұрын
Correct!
@JackInTheShop6 ай бұрын
Bring your kids to work day. Cool.
@SienciLabs6 ай бұрын
Ya, every once in a while they tag along. She was a fantastic helper that day! 😊
@MichaelBuilds6 ай бұрын
OH MY GOD THATS BAD A*S!!!
@SienciLabs6 ай бұрын
It really is! Thanks Michael!
@williamspencer52596 ай бұрын
Cool
@TheMowogman6 ай бұрын
Why are you using such a small surfacing bit
@craigrholmes6 ай бұрын
Maybe to show off? Haha
@SienciLabs6 ай бұрын
Because Andy crashed the big surfacing bit and bent the shaft of the tool 😥