EZ Style Cooler - Adding a Bottle Filler

[@elkayusa]

Continued steps from above: (5:19) STEP 34: For single model installations: Attach the purple wire from cooler to the purple wire on the back of the unit. (Note: Yellow wire is not used). For bi-level model installations: Attach the purple and yellow wires from coolers to the purple and yellow wires on the back of the units; purple to purple and yellow to yellow. (5:28) STEP 35: Once the bottle filler is installed on wall plate tabs, and the water line, wire(s) and power cord are installed properly, push the top of the bottle filler toward wall and line up the two top cover holes. (5:36) STEP 36: Reinstall top cover on bottle filler with two mounting screws from step 11 above. Caution, do not over tighten screws. (5:47) STEP 37: Install remaining tube insulation to the water line from bottle filler. Connect bottle filler water line inside of the water cooler by connecting the 3/8" water line to the T-Union. (5:55) STEP 38: Install trap. Remove the slip nut and gasket from the trap and install them on the cooler waste line making sure that the end of the waste line fits into the trap. Assemble the slip nut and gasket to the trap and tighten securely. (6:04) STEP 39: RECOMMENDED WATER SUPPLY LOCATION 3/8" OUTER DIAMETER UNPLATED COPPER TUBE CONNECT STUB WITH SHUT OFF (BY OTHERS) 3" (6:11) STEP 40: Install filter (6:21) STEP 41: Install filter by screwing filter in and making sure label is facing toward the front of the cooler. (6:30) STEP 42: Inspect for leaks. Fix all leaks before continuing. (6:37) STEP 43: Plug in bottle filler and cooler. (6:46) STEP 44: Verify proper dispensing by placing cup or hand in front of sensor area. NOTE: The first initial dispenses might have air in line which may cause a sputter. This will be eliminated once all air is purged from the line. (6:56) STEP 45: Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, adjust screw located on the left side below push bar assembly on crossbar. Clockwise adjustment will raise stream and counterclockwise adjustment will lower stream. For best adjustment, stream should hit basin approximately 6-1/2" (165 mm) from bubbler on the downward slope of the basin. NOTE: If continuous flow occurs at the end of the compressor cycle, turn cold control counterclockwise 1/4" turn. (7:05) STEP 46: Once unit is working properly, replace lower panel on water cooler(s). (7:14) STEP 47: Replace the (4) screws holding the lower front panel at the bottom of cooler. (7:24) Installation is complete.

[@jeffmckinney7811]

but where does the purple wire connect to inside the cooler. the video shows to connect it on the back of the bottle filler but doesn't show where to connect it to inside the cooler.

[@tommefoster1332]

@@jeffmckinney7811 I finally contacted Elkay directly. They said there is no longer any need to attach the purple wire.

[@kennethtyson570]

You never show inside the cooler where to connect the yellow and purple wires from the bottle filler for a bilevel installation nor where you connect the purple wire for the single installation?

[@svkurkovful]

I spent several hours trying to find out where that purple wire connects to.

[@tommefoster1332]

​@@svkurkovful I finally contacted Elkay directly. They said there is no longer any need to attach the purple wire.

[@Pharoax]

Thats in my school now

[@CoyoteRunChannel]

At no point in this video does it mention drilling the hole in the top of the drinking fountain. It just kind of "appears" magically. It also does not mention drilling any holes in the installation instructions. Come on Elkay....

[@Picklebean72]

If you watch it and actually pay attention, you can see that the basin was removed and replaced with the new one with the hole on it

[@DAVIDMITCHELL-z6e]

11 ENTER

[@DAVIDMITCHELL-z6e]

Enter