Don't glue the carpet. If you insist on doing it, only do it where you think it is necessary, don't hose the whole floor down with spray glue. IME, some of the Dynamat will soften at the seams and stick to the backside of the carpet by itself. Speaking of Dynamat, I know you said the doors are going to be replaced but if you have any scraps left, pull your door panels and stick them to the inside of the door skin. Even a small chunk of it can kill that tin can thing. Also, a tip for seatbelt and seat bolt holes. Instead of cutting an X with a razor knife or hacking the carpet out, take a chunk of copper plumbing pipe, heat it with a torch and use it to melt a circle where the bolt goes. I just did the whole carpet, interior paint and sound deadening thing on my 80s toyota 4x4 a few months ago.
@RalphSampson...5 жыл бұрын
Thanks for that great idea of using a heated pipe. Sometimes in construction, we will use a sharpened pipe to cut a hole for door stops. I like your idea. It will also melt (seal) the nylon threads to prevent unraveling. I supposed a wood block placed under the carpet while you are making the hole is needed, huh?
@waynehardy61865 жыл бұрын
That was the inspiration I needed to continue to complete my 91 F-150 , I've been having so many things come up to stop progress but every new video helps keep me going thanks.👍
@colemeyers11615 жыл бұрын
You should get sill plates for the edge of the carpet at the door
@gosportjamie5 жыл бұрын
While you can't lay the carpet due to the rain it would be good chance to throw some paint on bare metal paint on the part of the transmission tunnel that you welded up otherwise it will start flash-rusting as soon as there's any moisture in the air (like then) and before long it will start to get seriously eaten away by corrosion and you'll be back to having a hole there again...
@honda60155 жыл бұрын
gosportjamie I was thinking the same thing. He did everything perfect up until that part lol. You already have the primer and paint, just throw it in there real quick. Somethings better than nothing.
@zachariahlow68725 жыл бұрын
Carpet doesn't get glued to the floor. The seats, door seal plates, & seat belts are what hold it in position.
@ArcticAutoWerks5 жыл бұрын
No you need glue with this truck. I have the same one and just did so. Trust me
@cowboykai34985 жыл бұрын
It does get glued in
@zachariahlow68725 жыл бұрын
I've owned numerous 67-72 F100's & none of them had the carpet glued down. The jute backing was glued down in places. The carpet was held in place by the door sill plates & seat. The front was held in place by the toe board.
@ArcticAutoWerks5 жыл бұрын
@@zachariahlow6872 yes, of coarse from factory they dont come glued lol. After market carpets however need glue
@stevenmaines91145 жыл бұрын
Not one person who restore trucks or car glues there rug in watch other videos....
@stompbot2725 жыл бұрын
Maybe relocate the fuel tank. Cut open the old one , tack on a few hinges and make a hidden compartment.
@GoodOldMike3 жыл бұрын
this was a really helpful video as I'm getting ready to do the same on my 77 f100. thanks for the quality video!
@steve310t5 жыл бұрын
I have never heard of glueing in a automotive carpet, i have pulled many carpets out if vehicles to perform repairs and never has one been glued. Good luck
@novidsheremovealong18935 жыл бұрын
Steve Godfrey well, it wouldnt be glue, itd be more like epoxy, needs to be a little more rugged
@steve310t5 жыл бұрын
@@novidsheremovealong1893 well if thats his choice all power to him. Personally i wouldent
@travisbennett58395 жыл бұрын
If I wanted my carpet in my truck to stay in place I'd use velcro. Not glue or epoxy. Just velcro with some good sticky tacky adhesive to keep it strapped to the floor. That's how I did it in my '70 f100 and worked out well. Easy to lift up if ever needed and stick it back in place.
@lancebowers65915 жыл бұрын
Dude that looks so good already. Some people think you can't use a rattle can, if you do it right you can, and you did.
@fender52475 жыл бұрын
You have done a amazing job on your truck I’m very impressed keep the videos coming
@johnwelsh2497Ай бұрын
"Shawn with his stupid Jeep!". lol, Great video, I just got my first "old truck/car". I got a 1965 F100 standard cap long box. I'm loving the step by step details you are giving and the fact that the 'average Joe' can work on these with good outcomes. I really don't have any plans to spend $$$$'s on this truck but want it looking good... It's just an old truck to go on Nebraska gravel road rides with the wife and the hound. Keep up the great work. I see this video is 5 years old, so I'm looking forward to learn through your other videos.
@Petrol3605 жыл бұрын
Iv got to go with everyone else, dont glue the carpet down! Its a fitting carpet kit so the seal plates will hold it in place. We never glue carpet down at work unless you absolutely have to. It will make your life a pain if you ever have to pull it up to run wires ect. Plus glue will rip the foil off of the dynomat when you try to rip it up and can really mess up the hole floor. Good to know how much dynomat it took to do the cab though, might to the cab on the 64 one day.
@joser51935 жыл бұрын
Na Not a waste of time It’s all great content Without knowing Your help is all along the way. Thanks for sharing all your experiences so far. Keepem coming Thanks Again.👍👍👍👍
@davidjames27885 жыл бұрын
It's looking good! A nice interior really transforms a car.
@Viktorrhansen5 жыл бұрын
Gonna be insane to roadtrip this truck man :D
@mark980705 жыл бұрын
Instead of glueing the carpet down I'd just use some 3M spray adhesive only in areas where the carpet didn't fit down tightly. Great job with the Dyno-mat!
@olmoe11675 жыл бұрын
She's looking good, Craig....Big improvement...
@TheCrackerBox5 жыл бұрын
It's sounds quieter when you're in the cab talking you can tell the difference Awesome job looks great
@Dmar10785 жыл бұрын
Its coming along it looks good. I can't wait the see the finish.
@HammerPowered5 жыл бұрын
Amazing what a little elbow grease and some spray paint can do. Work looks good so far. I second the sentiments of others about not gluing the carpet down. The seats, seat belts, and any other trim is what holds it in place, so there's no need for applying an adhesive.
@douglasdailey59984 жыл бұрын
Looks like you are doing a pretty good job, and you are right do everything while you have it apart.
i’ve got a 79, been thinking of getting the same carpet kit from LMC and this video sure as hell pushed me over the edge and it will be ordered here soon!
@stoveboltlvr37985 жыл бұрын
Looking good, take your time. Maybe paint the pedal brackets and column with satin black Rustoleum. Door sill plates will look good too. Also be careful around that loop carpet with drills, it'll grab it in a hurry and give you a runner you don't want!
@billybb174 жыл бұрын
Hope that cold isn't related to the Corona Virus....I always let your ads play out to benefit your work on these vids... great job and enjoy all you do from here in Dearborn Michigan
@makerviewscom4 жыл бұрын
Likely adding Dynamat to my 71 F-250 Camper Special - awesome to see how that process went on your Ford. Thanks!
@JRC995 жыл бұрын
It's about damn time you put carpet in it lol. Looks great!
@peterherring87014 жыл бұрын
Im doing the same thing. I instaled a Firewall pad the covers the firewall and top of carpet.
@tannerwimer5 жыл бұрын
Can’t wait to see it all together
@GooeyThaGamer5 жыл бұрын
Try eBay for a firewall pad, I bought one and was very happy with the quality. The one I got is made of rubber not crappy "cardboard" like the original ones. Only cost me around $70 and I'm very pleased with it, it fit perfect! Definitely give it a look
@pinstripingbybear.5 жыл бұрын
Just a heads up man a full white topped dash is not the best idea the white with a gloss will flash on the windshield kind of like driving around with a piece of paper on your dash that puts up white glare on your windshield this is just from experience. And being a pinstriper of 12 years
@travisbennett58395 жыл бұрын
Yeah he definitely needs a dash pad. A nice soft leather black one. It would really tie up with the rest of the interior and look sharp.
@NEWORLEANSYAT5 жыл бұрын
did not glue mine and its perfect
@gosportjamie5 жыл бұрын
I imagine the truck would have originally had factory sound deadening on the upper parts of the bulkhead above where the carpet ends, the old jute fibre stuff with the tar cover over it, so having the unfinished bulkhead above the original carpet or rubber matting wouldn't have been noticeable. Of course that old sound deadening doesn't last too well in hot areas like California being as it is just glued on and the adhesive doesn't survive the heat very well. Eventually it fails in enough places that the weight of the pads pulls it all away from the spots where it is still stuck leaving those patches of ginger fluff you often see in old vehicles...
@keithskustoms23113 жыл бұрын
Firewall installation pad is supposed to go in there, that is what covers the metal where the carpet doesn’t cover.
@tannonlortonjr.15125 жыл бұрын
You should rino line the floor and put the carpet on just for safe measure of no rust
@stompbot2725 жыл бұрын
Don't disconnect the fuel line. Just cut the carpet.
@joeschlotthauer8405 жыл бұрын
Footstep trim piece is a Sill plate... Velcro the carpet in..
@travisbennett58395 жыл бұрын
Yes, velcro works well. been holding the carpet down good in mine and has lasted a long time to.
@eanhartman95745 жыл бұрын
Looks sick dude! You did an amazing job as always bro
@samuelberry6785 жыл бұрын
There is a plastic/rubber (depends on what company you get it from) shield that goes from the carpet up the fire wall that helps hide the carper seam at your feet.
@akribela5 жыл бұрын
Your channel is awesome!! I'm almost ready to lift my engine out. Having my 390FE rebuilt w a Performer Series Eldebrock intake & 750 carb, comp cam, 0.030 bore. Having trouble finding a set of hedders that have a bigger flang than 5/16". My truck is a 76 F250 390FE M code , Custom Camper Special w dual tanks, C6 auto, 3.54 Ltd slip Dana 60 rear end. Will be Dynamatting mine also. Keep up the great work!!
@quasidragon075 жыл бұрын
dude that dynamat is awesome that before and after is a HUGE difference
@brucedrake9045 жыл бұрын
That's funny you taped off the name on the spray paint then said the name of it lol looking Sharp
@QSAUnited5 жыл бұрын
I love this!!! Good shizz Craig!!!
@LWNDmax5 жыл бұрын
Looks great bud!
@johnwalton99595 жыл бұрын
Great job! Looks good!
@Tomcaatt4 жыл бұрын
My 62 is primed up inside and am thinking about finishing it , but ,Cali is a great place to paint w no humidity and it all drys fast anyhow it’ll be fine ( try that in Memphis (wich I’ve done since 78), the humidity is heavy with hazing sometimes without a controlled envirement anyhow , lookin good ,
@edmundp123 Жыл бұрын
Lot's of good info.
@Tomcaatt4 жыл бұрын
My 62 is primed up inside and am thinking about finishing it , but ,Cali is a great place to paint w no humidity and it all drys fast anyhow it’ll be fine ( try that in Memphis (wich I’ve done since 78), the humidity is heavy with hazing sometimes without a controlled envirement anyhow , yo truck is lookin good son.
@punkinsgarageandpaint82995 жыл бұрын
Really good job.
@stephenmanion34183 жыл бұрын
very impressive my friend.!!!!
@jameslittle39315 жыл бұрын
Wow you keep going your going to have that new car smell in your truck
@AboutHorsepower5 жыл бұрын
Holyy crap that looks mint
@skittlesryumm5 жыл бұрын
wow that looks great
@masonrichardson65813 жыл бұрын
I've got the same problem, my firewall cover was all damp so I tore it out. Not saveable, and I'm not spending $300! I'm sure for such a small strip we can make our own.
@sparkyguy2775 жыл бұрын
Nailed it!!
@justingriffith13705 жыл бұрын
Looks awesome!
@faronf20065 жыл бұрын
Awesome job so far but I would not glue the carpet . The seat door sill plates etc will hold everything in place . Just let that carpet naturally settle & it will in time . Once glued in just a real pain to remove for any reason down the road .
@joe_kaiser21365 жыл бұрын
the metal patch turned out better than expected tbh
@shixson9575 жыл бұрын
Good work Man!
@caseymaples19xx3 жыл бұрын
Looks great
@FourSpeedFilms5 жыл бұрын
Clean! I put Dynamat in my mustang!
@colealexander52845 жыл бұрын
National parts depot makes a replacement firewall pad that finishes the carpet edge up to the firewall
Glue in the carpet... WHY? They were never glued in at the factory. Nice solid F-100! Love the Ford trucks. I have owned many Ford trucks. I have a 2008 F-150 that I bought new.
@GTABLAST-zw6ye5 жыл бұрын
I thought you traded the green seat belts for black ones?
@rileyweeks37255 жыл бұрын
In my 73 it has factory insulation in the roof which may help with the noise and heat. Just my .02 cents
@AboutHorsepower5 жыл бұрын
Glazing powder on those little bumps
@lomgshorts35 жыл бұрын
Funny, my '68 F-350 had full metal inner roof panels, no headliner or middle seam, came from the factory that way. Why didn't your F-100 come that way?
@rawdyrider5 жыл бұрын
Have you seen those laser rust removers?Bloody amazing!
@steedscutt61835 жыл бұрын
looking mint man
@michaelwilliams69225 жыл бұрын
Loving it!
@thomaskingdon11772 ай бұрын
Beautiful Workman I'm curious where did you get the carpet what website what company and what's the brand?
5 жыл бұрын
Nice interior.
@williamsanders4685 жыл бұрын
Seats should look really nice with the carpet
@physkogamer71395 жыл бұрын
Man that looks so good. Let us know how it is further down the line. Been looking at getting a carpet kit for a while for my truck but just can't decide on which one.
@andrewshutt24595 жыл бұрын
Awesome!!!!!
@NICKSSHOP5 жыл бұрын
ur tuck is looking great
@terryspear85335 жыл бұрын
Looks good
@joeschlotthauer8405 жыл бұрын
Good and bad from LMC? What was the bad, I heard of "quality" issues....
@yeboscrebo44513 жыл бұрын
I got a carpet from Stock Interiors and they just threw the edging trim stuff in the box like I’m supposed to sew it on myself! I don’t know what I’m going to do now I don’t have a sewing machine or the time to worry about one more thing
@ZacCjw5 жыл бұрын
Paint firewall black? Gloss or matte? Would help it blend in
@travisbennett58395 жыл бұрын
Exactly.
@fishnfreak045 жыл бұрын
Also yeeeeeessss another vid
@jr.torres44914 жыл бұрын
Hey whats up bro back when you primer the floor on the f150 , how many coats did you do ?
@1977jed5 жыл бұрын
What I have done, and it may keep your mind at ease til you can afford the firewall cover....Just use some good sturdy cardboard and paint it Matte black....Will get ya by til you can afford the one you want.....
@ArcticAutoWerks5 жыл бұрын
I have the same truck and just did all this as well. I'm about to do new rubber trim all the way around. Are you ganna make a video on doing this anytime
@corndogextreme88875 жыл бұрын
I would have done the vinyl floor carpets nice but then you worry bout spilling stuff
@jermvp5143 жыл бұрын
What kind of paint and clear coat did you use? Might be doing this to mine soon.
@shartne5 жыл бұрын
Nice.
@305iglesiasАй бұрын
Is that one of those rubber carpets or regular carpet. I can’t really tell.
@thebestojf71603 жыл бұрын
What clear coat did you use?
@freddyz93635 жыл бұрын
Firewall pad and insulation
@rawdyrider5 жыл бұрын
Get some 3M double sided tape and "tack" the carpet down with that.Do not glue it!
@COJackgame5 жыл бұрын
Happy new year
@quintenlowery95435 жыл бұрын
What carpet kit did you order Doing the same swap except with a zf5. Want to make sure it fits around the new tunnel correctly
@wannabeerc5 жыл бұрын
Steam and that roller of yours would lay that carpet down and everyone is right. NO GLUE>
@nathan49195 жыл бұрын
Build a console but wait until you add a turbo so you can add gauges to it may be cool lol.
@eddieboy93495 жыл бұрын
Like before i even play the video,💯
@BC-iz8gt3 жыл бұрын
Hey hey can you tell me how you did the instrument panel or where I can get one like that
@adamblue74415 жыл бұрын
Hey Craig what happen to your best friend Chris the guy guy that drives the iroc camero.where is he