Step by Step guide to installing the new FCS II System.
Пікірлер: 26
@amorton943 жыл бұрын
I can't wait to model and 3d print all of this install kit for free instead of getting that $100 kit.
@mathieugiusti38598 жыл бұрын
Hello @FCSFINS , I broke a plug on my brand new Timbertek Firewire, a shapper tryed to fix it, BUT I exercised pressure who push the plug, again... So the question is do you have a trick to fix it sustainably 100% ? Thank you in advance.
@homerilias6 жыл бұрын
And I was always wondering how the shapers get the cant angle correctly. Because it creates lift, lack of precision in that might make the board behave a little strange.
@nickturner8844 жыл бұрын
Is the router set to the depth of the inner part of the fin box where the fin goes in or set to the outer edge part of the box ?
@FCS_Surf10 жыл бұрын
Hi Eduardo, thanks for your interest. To purchase FCS II plugs and Install Kits you will need to be a manufacturer/shaper and set up an account with us. Please contact our USA Team for more details www.surffcs.com/support
@michaelangelos51177 жыл бұрын
is that a stewart s winger?
@jmhernandez65039 жыл бұрын
Hello! Was that the Makita 1-1/4 HP Compact Router used in the video?
@tireballastserviceofflorid77718 жыл бұрын
+J Hernandez Looks like it.
@fcp44233 жыл бұрын
You mention 8ml of resin but not how much cabosil to add. How much per cavity?
@HRuss1232 жыл бұрын
How do you not cut into the template jig? I have ruined my template from Greenlight 🧐
@PMAPMAPMA134 жыл бұрын
How are these stronger than Fusions?
@eduardosustovich846510 жыл бұрын
Where can i buy the FCS II plugs in USA??? Thanks
@yensysaerialimaging35239 жыл бұрын
Eduardo Sustovich hey brother...check foamez
@oldguyfun10 жыл бұрын
What is the advantage of FCS 2 over the last FCS system?
@dadthelad4 жыл бұрын
FCS2 fin plugs are much stronger than FCS, due to FCS just being 2 little round plugs, whereas FCS2 is a longer oblong plug, so you are much less likely to need the plugs on the board repaired. The fins themselves also have stronger, bigger tabs, so are less likely to break at the base. Also, the FCS2 fins have a lot more variety of shapes and stiffness for different waves and riding styles, and have a variety of higher quality materials, or cheaper options. FCS2 plugs can also take both FCS and FCS2 fins. Also, in my own personal experience, FCS2 fins are so easy to install and remove compared with Future Fins. All the Future Fins boards I've owned had imprecise fin boxes and fin tabs, so I had to sand down the tabs to even fit some of the fins in. And then months later, when I wanted to swap some fins out, they were so stuck in it was like they were glued in. I've switched to FCS2, and so far it's a breath of fresh air. NB, I still use a single grub screw to ensure the fins don't pop out if they bounce off the sand at the wrong angle, as I've heard of guys losing fins due to this.
@rayr.55573 жыл бұрын
So we will buy more replacement fins. First wipeout on a new board, one fin gone immediately. No grub screws, no fins!
@dropknow4 жыл бұрын
What speed is used on the router?
@Jpgundarun2 жыл бұрын
On
@taylorburroughs67458 жыл бұрын
Can someone please help me? I got a new board withut fins but it doesn't fit fcs2 fins and it has a flat line instead of the two holes. Anybody know which fins fit these? (thruster)
@camerondavid80898 жыл бұрын
+Taylor Burroughs Probably futures!
@diaperjuice_48537 жыл бұрын
Taylor Burroughs yeah futures
@gregschannel49183 жыл бұрын
Hardest part is getting the fin into the plug
@scottdavis89953 жыл бұрын
if that is a 9degree fin why does he have a 7 degree cant angle jig??
@boccacantiga50953 жыл бұрын
concave in the board where the jig rests. they aren't literally 9 degrees in relation to the bottom of the board but a hypothetical level line from rail edge to rail edge. also, there is wriggle room to set a different angle. in the factory some shapers stipulate different degrees and we simply used 9 degree plugs and set them to the desired angle. as long as it's not more than about 2 degrees different it is fine.