Festool Live Episode 163 - Domino Edge

  Рет қаралды 14,516

Festool USA

Festool USA

Күн бұрын

Пікірлер: 11
@Billy_bSLAYER
@Billy_bSLAYER 11 ай бұрын
Just got the CT-MIDI I, CT-VA (dust seperator), and the Rotex 90 from Rockler in Buffalo and I must say my wife and I are amazing that we were sanding/stripping these old kitchen cabinets with literally no dust, no vibration, no reaching for the vac power button... Not to mention just an overall quiet work environment. Thanks again for all the great information, have a great weekend. Brian
@ksphoto1
@ksphoto1 11 ай бұрын
question for you, if I need to be less than the 37mm is it best to utilize the scale right above the bit? I haven't seen you address this. I love the stops, but in the pieces I am working on I need it to be a lot less.
@huang3218
@huang3218 10 ай бұрын
I want to own this device but don’t know where to buy it
@jgarehart89
@jgarehart89 11 ай бұрын
Missing link to lost in catalogue episode for OF 1010 edging plate, deflector and angle arm setup
@TheDanarone
@TheDanarone 11 ай бұрын
I went through this when I borrowed my buddies Domino. Seems like a design oversight by Festool not to have more increments on that adjustment if you ask me.
@stakwalderbak5331
@stakwalderbak5331 11 ай бұрын
It's about time Festool brought out a lipping plane. I bought a Virutex Lipping Plane ($AUD700) a few years ago and, after the buyers remorse subsided, I discovered how much time it saved and how many jobs I no longer screwed up. Of course I still use my Domino but now I don't have to worry so much about my inevitable close calls.
@ohnoitscoolbreeze
@ohnoitscoolbreeze 11 ай бұрын
I second this. I was lucky to find a barely used Lamello Cantex for a good deal and it’s such an improvement over the flush trim bit/jig connected to a router. I’d love to see what Festool would come up with
@SaleemHodge
@SaleemHodge 11 ай бұрын
Happy Friday from Federal Way!
@benno390
@benno390 11 ай бұрын
Why not just reference the plate of the domino to the height of the plywood on a flat surface to the roughly 18mm? Seems like you could cut out a few extra steps rather than shimming the plate to an offset to get you to pretty much the same place
@RWingoS7
@RWingoS7 11 ай бұрын
My guess is because if your trim piece isn't perfect, or your plywood surface isn't perfect, you could have slight gaps to fill instead of sanding it down to be perfect across the joint.
@Wolf-yw7en
@Wolf-yw7en 11 ай бұрын
What’s this. A Woodpeckers shim in a Festool product promo. Lol!
Festool Live Episode 124: DOMINO Accessories
32:31
Festool USA
Рет қаралды 13 М.
Secrets to Building TIMELESS Mid-Century Modern Designs
40:03
Sawyer Design
Рет қаралды 21 М.
Quando A Diferença De Altura É Muito Grande 😲😂
00:12
Mari Maria
Рет қаралды 45 МЛН
It works #beatbox #tiktok
00:34
BeatboxJCOP
Рет қаралды 41 МЛН
Мен атып көрмегенмін ! | Qalam | 5 серия
25:41
Festool Live Episode 161 - Ergonomics
39:41
Festool USA
Рет қаралды 4,8 М.
Festool Live Episode 143 - Face Frame to Bottom: Cabinet
40:56
Festool USA
Рет қаралды 13 М.
Festool Live Episode 11 - Domino DF500 Connectors
37:35
Festool USA
Рет қаралды 36 М.
Cabinets are expensive. Do this instead.
26:49
wittworks
Рет қаралды 815 М.
Festool Live Episode 165 - Rotex RO 90: Small But Mighty
34:17
Festool USA
Рет қаралды 12 М.
All You Need To Know About The Festool OF1400 Router!
22:56
sedgetool
Рет қаралды 66 М.
The New Age Of Woodworking
46:23
Pedulla Studio
Рет қаралды 881 М.
The real domino killer?
15:24
Lincoln St. Woodworks
Рет қаралды 1,3 МЛН
Festool Live Episode 32 - Domino Drawer Box
39:10
Festool USA
Рет қаралды 49 М.
The Top 4 Festool Domino Joints You Need to Know
16:13
sedgetool
Рет қаралды 159 М.
Quando A Diferença De Altura É Muito Grande 😲😂
00:12
Mari Maria
Рет қаралды 45 МЛН