Very nice video - my Strada didn't break the cambelt, but the previous owner abused the living daylights out of it so it just died mid-drive. Luckily I was going at about 60kPh in 5th gear when disaster struck so only the intake valves were slightly bent. When I had it stripped to check why it died I found out that the previous owner had let it overheat and never fixed it, hence my having performance issues since day one. I'm still not 100% sure why it bent valves since the timing belt didn't break and there's no visible wear on the belt itself, but I suspect something got between the sprocket and the belt which made it skip some teeth without actually damaging it. The plastic around the cambelt was quite damaged so anything is possible. I'm waiting for the head to get back from the engineers then I'm putting it back together. Doing it myself, since I almost had a stroke when they told me it would cost R15000...
@zvonkonikolic3 жыл бұрын
Great video. It helped me a lot when replacing the valve oil seals on my Fiat Stilo 1.6 16v !!!
@vehiclemaintenanceandrepai37903 жыл бұрын
Thanks for the support Zvonko, greatly appreciated.
@titustizirai37064 жыл бұрын
well filmed n good explanations on point I come across this while I am battling w e same engine timing but well said I hv to get the timing tool set
@daccuiz3 жыл бұрын
nice work sir very good!!! i have a question sir the hole on gear box isnt have any cap on it?? so that nothing can fall in it (a bolt or anything)?? i think is risky if something fall in it . its from factory without a cap or a cover???
@vehiclemaintenanceandrepai37903 жыл бұрын
Hi Dacozzu, you are correct, there is a plastic/rubber cover to prevent debris and other objects entering the bell housing, thanks for your support, it is greatly appreciated. Gary
@DavidBakaDontBelieve5 жыл бұрын
Nice video to learn new knowledgee👍👍👍
@DavidBakaDontBelieve5 жыл бұрын
@@vehiclemaintenanceandrepai3790 you welcome sir i really appreciate your shares and tips..it is not easy to become a mechanic.. cause i myself also a mechanic still alot things to learn and not so much people willing to teach in my area anyway..all i can do is learning from youtube thats where i saw you video .. thanks for the knowledge sir
@ruan25875 жыл бұрын
Great learning experience, thank you.
@EmilyBrokenhoff Жыл бұрын
Hi sir like your video, just wanna know where we find a new top for a 2009 strada. And how can we can fix a skeemed top please and thank you.
@vehiclemaintenanceandrepai3790 Жыл бұрын
Motor engineers will be able to skim a cylinder head to find a new head for the Fiat you have to search the internet.
@uncomfortabletalktv1642 жыл бұрын
HI can you please explain, I have a palio 1.2, change the block. but the starter did not fit. The mechanic I used can explain. the thin starter fits. I wana know why. old block 2003 takes fat starter, new block 2005-2008 takes thin starter I am still confuse on this issue
@lehlohonoloraliboke1726 Жыл бұрын
Hey can you help me out figuring out, if I put on the cylinder head while the crank is not top dead, then it wont go to top dead center. this is what happened and i'm trying to figure out why my crank shaft wont turn 360, is it because i installed the cylinder head while crank was not at top dead? is there anyother way i can still set top dead center without having to remove the cylinderhead?
@patmasilela89622 жыл бұрын
Great video
@TshepoNkosi3 жыл бұрын
I very great video, Can fix my Sienna 1,6 16v?
@vehiclemaintenanceandrepai37903 жыл бұрын
Thanks for the su[port Tsehepo, I am happy you found the video useful.
@alljoy65415 жыл бұрын
Wow Garry, that was incredible. The owner actually paid to get it repaired, must have cost a fortune. Would it not be easier to scrap the vehicle? As it is old, instead of wasting money fixing again and again with little joy.
@kiyoponnn4 жыл бұрын
@All Joy It's already been established that the owner lacks common sense
@kiyoponnn4 жыл бұрын
@@vehiclemaintenanceandrepai3790 Agreed
@bonganiautomaseko74754 жыл бұрын
Great workmanship
@dsilvermane02 жыл бұрын
Considering I got quoted R15000 and my Strada cost me R75000 I really don't see how scrapping it would be worthwhile. In addition, I decided to do the repairs myself, which turned out to cost me less than R6000. Not everyone's circumstances are the same.
@ompotho Жыл бұрын
Dear sir. My brother is struggling with his strada bakkie with the same cams. Please get in contact with him.
@dragosmotiu26983 жыл бұрын
great job ! i know that this engine mounted on fiat Brava has a special kind of bolt pattern for the head and the camshafts, it's called ribe. they are almost like torx, only that they are square ar the top of the rays.
@vehiclemaintenanceandrepai37903 жыл бұрын
Yes, I have seen that Dragos, thanks for your interaction and for supporting my channel with your visit, it is greatly appreciated and means a lot to me. Gary
@wordaliveministriesrandfontein11 ай бұрын
The 1st and 4th piston is at bottom dead center on my car when the mark on the flywheel is pointing to 0...what could be the reason for this?
@vehiclemaintenanceandrepai379011 ай бұрын
The flywheel was removed at some stage maybe when the clutch was done and not put back correctly.
@abnerabcnegonga49934 жыл бұрын
What cause the timing belt to break down continuously in fiat strada 1.6 ELX engine?
@vehiclemaintenanceandrepai37904 жыл бұрын
Hello Abner, a good question I will answer best I can. It could just be a matter of poor quality parts used. The tension on the belt could be wrongly set, (too tight or too loose) in both cases the belt will be under too much stress and break prematurely. The gears the belt runs must be inspected properly for sharp edges caused by knocking that could prematurely wear the belt as it is made of a rubber compound and is prone to be cut by sharp edges leading to early failure. When the cam belt gets soaked with engine oil due to cam and crankshaft seals leaking, this will also weaken the belt and cause breakage. And of course, driver abuse as some folks are just hard on cars. Although these answers may not be exhaustive, it is the main ones to cause untimely wear in my experience. Do not forget to subscribe and press the bell icon to notify you of all newly released videos on my channel and check out my website for more useful information. www.vehiclemaintenanceandrepairs.com/
@phillipmhlongo80383 жыл бұрын
Where can I find the special tools for the Fiat palio weekend 1.6 16v 2003 model
@vehiclemaintenanceandrepai37903 жыл бұрын
I have one for sale, R1500, alternatively try Diesel Electric 0217065552
@lehlohonoloraliboke17262 жыл бұрын
great vid
@vehiclemaintenanceandrepai37902 жыл бұрын
Thanks
@lehlohonoloraliboke1726 Жыл бұрын
@@vehiclemaintenanceandrepai3790 I cant turn the crank to top dead center, it gets stuck, but it was turning freely before I installed the cylinder head, idk what might be the problem
@vehiclemaintenanceandrepai3790 Жыл бұрын
I think they may have over-skimmed your cylinder head Lehlohonolo, now the valves are touching the pistons when you turn the engine, or the engine is not timed properly, did you use the special tools specified to do the job correctly?
@lehlohonoloraliboke1726 Жыл бұрын
@@vehiclemaintenanceandrepai3790 i used the tools, it touches even without the cams on. i think it may have been over skimmed😭
@vehiclemaintenanceandrepai3790 Жыл бұрын
Thanks glad you liked it
@wietsfouche6343 жыл бұрын
Can you perhaps help with teeming mark alignment on a fiat siena 1.7 td
@vehiclemaintenanceandrepai37903 жыл бұрын
Hi, Wiets I do not think the petrol and diesel versions are the same, do a google search on the diesel motor there are a few good ones.
@SlowSlow698 ай бұрын
how dow u locke the crank shaft in place
@vehiclemaintenanceandrepai37908 ай бұрын
Remove the starter to access the flywheel and lock it by putting an old screwdriver in between the teeth to lock the crank and prevent it from turning. Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.
@mtutuzelisishuba60024 жыл бұрын
Where can one get that special tool?
@vehiclemaintenanceandrepai37904 жыл бұрын
I have 2 sets, 1 is for sales R2000, contact me on 0724867810, if you are interested.
@brianduplessis86066 ай бұрын
There must be marks on the top pulleys
@vehiclemaintenanceandrepai37905 ай бұрын
Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.
@brianduplessis86066 ай бұрын
Why dont you show the marks on the top pulleys not everyone has got the lock tools for the cams
@vehiclemaintenanceandrepai37905 ай бұрын
You should not attempt a job without the correct tools, this comes from a 35+ year mechanic veteran.
@brianduplessis86065 ай бұрын
@@vehiclemaintenanceandrepai3790 old school guy i came right anyway thank you for your reply