Fiesta ST Build [Pt.18] "6-Point Brace and Sway Bar Install"

Today we are adding a Eibach Front Sway Bar and a Pierce Motorsports 6-Point lower chasis brace that we hope removes a bit of torque steer found on FWD cars.
Also Buy stuff on Amazon: amzn.to/2KNazSI
---------------------------------------------------------------------------------------------------------
As always, if you enjoyed this video and found it in any way helpful, please hit that LIKE button. If you know anyone else who may benefit from this video, because their doing a similar project, then don't forget to SHARE this video everywhere. And if you haven't already, SUBSCRIBE.
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------
For updates on new projects Follow me on INSTAGRAM
@INITIALIZED_FRS
--------------------------------------------------------------------------------------------------------
Music:
ChillHop Music:
/ chillhop. .
NCS:
/ nocopyrightsounds
Artists:
GYVUS
GlobulDub
Kozah
Raven & Kreyn
Jeff Kaale
Star Party
Soul Chef

[@drgnslyr9184]

that 13mm sway bar bush bolt made my pinky swollen for days.

[@jacobusenmez8506]

I’m so grateful for very informative tutorials like this. Please carry on uploading more content as whole ethos of KZbin is all about this. Thank you 🙏🏻

[@gerardorios6821]

Donde puedo conseguir la barra de 6 puntos Where can I buy this 6 point brace?

[@alejandrowilcox763]

I have a question. (off topic from this video ) but have you ever tought of changing out the throttle body spacer and intake manifold spacer ? Im thinking about getting both from boomba but i heard there is no gain from it and its also a pain to install them .

[@JonnyBarajas]

The throttle body and intake manifold spacers are used for extra injector capabilities for port injection fueling to run over 300hp. I have an intake manifold spacer with a single injector. The spacers themselves don't increase hp or torque in this case. Yes, the intake manifold spacer is a pain to remove and line up.

[@Basement_Operator]

Yeah the brace is a PITA lol. It's worth it though

[@manuelgarcia1835]

Hi, what charge pipes are you using that clears the 6 point brace?

[@JonnyBarajas]

ATP hot side charge pipe.

[@manuelgarcia1835]

Thanks

[@mikeynguyen4329]

Did you install the rear sway bar or nah? Does it understeer a lot with the 6 point on there?

[@JonnyBarajas]

We did add a rear sway bar later on. The 6-point actually is what removed the torque steer almost completely.

[@mikeynguyen4329]

@@JonnyBarajas cool! I'm debating on whether or not to add a rear sway... So I have a 6 pt Brace now. Would adding just the front sway bar with the Brace be too much understeer?

[@JonnyBarajas]

@@mikeynguyen4329 The rear sway bar allows for controlled oversteer when turning fast and removes a center spin feel when turning. Front sway bar helped with the body roll, and the brace and alignment will help with torque steer. Understeer shouldn't be a concern at all, and a set of sticky tires at 200 tread wear will help with understeer if you are thinking about it.

[@mattbouhuys2929]

Does the brace stick out under the car? Like if you went over a tall speed bump, will it scrape or hit the ground?

[@JonnyBarajas]

Only comes down about an inch or two. Maxed out on b-spec coilovers and never even think about scraping. But definitely the lowest point of the car.

[@mattbouhuys2929]

Jonny The Car Doctor awesome. Good to hear. I’ll probably pick one up, I’ve heard good things. Can’t wait to see your FIST fully built!

[@arsmusica23]

After installing my front sway bar, my car makes all types of creaking noises…does that mean it was installed incorrectly?

[@JonnyBarajas]

That might be something else. I got a clunk on speed bumps when my top endlink bolt was loose. Apart from that, never made noises.