Filling and bleeding a LS hydraulic steering system for outboard motor

Important recommendations
Tools required for the installation
- 1 set of spanners: 13, 14, 27
- Oil LS or oil with ISO 22 viscosity
- Only use oil LS or oil with ISO 22 viscosity.
- Make sure that the hydraulic piping is perfectly clean and keep the oil free from impurities which may cause the deterioration of the components of your hydraulic steering system.
For more details, please refer to the instructions provided with your product.
www.ls-france....

[@kmatejovsky]

Very soothing guide and classy video. I shall buy the #40 ST 16 Linear Drive for my sailboat. Because this is such a sweet video.

[@nickkostakis9600]

Great video and very well presented thank you very much from Sydney Australia 😊

[@lsfrance]

Thank you for your comment

[@maxsuelito]

Easy merci pour ce très bon tutoriel clair net et précis

[@AchikSarih]

Merci beaucoup

[@lachaudiere]

Tutoriel très bien réalisé : la classe!

[@lucianoa.fabricio6762]

Thanks for share! Helps a lot.

[@vicentearevalo3436]

Muy interesante gracias

[@sulimandc3467]

Thank you so much. It was unique video. You have a professional techniques

[@AchikSarih]

❤❤❤❤❤❤

[@manvill5349]

Bien réalisé dommage de ne pas avoir mentionné les dimensions : clé,tuyau de purge... Norme et qualité d'huile utilisées Mais super vidéo Bravo !

[@lsfrance]

Bonjour et merci pour votre commentaire. Nous avons ajouté quelques éléments techniques dans la partie descriptive de cette vidéo.

[@dugard7967]

Merci pour la video

[@CaptDavesSportfishing]

B-E-S-T TUTORIAL OF THIS JOB❗❗❗❗❗❗

[@mat9729]

Au top merci ! Par contre vers la fin à 4:30, il reste de l'huile dans l'entonnoire et à 5:04 il n'y en a plus.... Et a priori le reservoire était plein déja à 4:30, donc l'huile a du etre retirée manuellement ?

[@lsfrance]

Bonjour et merci pour votre remarque tout à fait justifiée. Selon la quantité d'huile versée durant l'opération, il peut en rester plus ou moins dans l'entonnoir. Dans le cas d'un "trop plein", il faut effectivemment evacuer l'huile manuellement. Le montage vidéo ne montre pas cet aspect.

[@mat9729]

@@lsfrance J'ai fini l'installation hier sur un Mercury 115. Materiel acheté chez Polymar en Martinique, vraiment super matos, RAS pour l'installation......

[@evadnamanelo4513]

Merci ça ma beaucoup aider 👍👍👍👍

[@PESCAENGA12]

buen trabajo y de un Yamaha

[@commonsense2574]

My Sea Star system has no fill fitting on the top of the helm out in the open, I have 2 on the underside, tried the lower and never got any air bubbles back at the helm tube, took very little fluid and saw plenty of bubbles back at the motor, I did not pierce the bottle. Needless to say it only kind of worked because I was cracking the fittings at the rear to get some air out. I have yet to see a video with No fitting on the helm side at the top, just the pair on the underside, mine is a tilt btw.??????

[@lsfrance]

Good morning Sir, Usually, you have a filler cap like we do at LS. It may be behind the transom, depending on the model. For filling, we use a funnel in our tutorial, but I think you can use your oil can and pierce it. I think the best thing to do is to contact SEASTAR and ask them for an instruction manual adapted to their direction. Best regards.

[@DirtMcGert29054]

Please make a stab at the US/NA market at put those scum bags at seastar into bankruptcy and hopefully prison