IT'S ALIVE! GOT THE GASSER WAGON RUNNING JUST IN TIME FOR THE NEW OWNER.

  Рет қаралды 137,656

Finnegan's Garage

Finnegan's Garage

Күн бұрын

Пікірлер: 484
@chuckmather3837
@chuckmather3837 2 күн бұрын
I felt really old when neither of you recognized the voltage regulator. I got my first job as a mechanic in the mid 70's and external regulators were on their way out even then. I enjoy watching you guys whether you're doing high quality fab work or just getting it running.
@txprospector
@txprospector 2 күн бұрын
Me too!!! I was surprised as hell neither of them realized it was the external voltage regulator. I had a '72 Chevelle and currently own a '68 and both have external voltage regulators. Had to check a electrical schematic the whole time I"m hollering at my computer screen "It's a volltage regualtor!"
@laynedouglas5105
@laynedouglas5105 Күн бұрын
Yup, voltage regulator. Are we really that old??
@tsufordman
@tsufordman Күн бұрын
I still run tractors with generators and those style voltage regulators.
@TakuroSpirit77
@TakuroSpirit77 Күн бұрын
What's worse is I recognized those wiring clips as the same as what my Harbor Freight trailer came with 🤣
@greghansard357
@greghansard357 Күн бұрын
Me too. Made me feel ancient.
@jefscoupe32
@jefscoupe32 2 күн бұрын
Throw in that stock gas tank for him too so he can use the cool 57-only hidden gas fill door. (yes 56 is hidden too but it's different from the 57) I had the same rubbing issue in my 55 Handyman. I just bent and hammered (carefully) the lip where the top and bottom of the tank comes together (where it was rubbing the diff) for clearance. I can't believe you guys are young enough to not know a voltage regulator. Damn, I'm old... LOL
@edwardbarnes2910
@edwardbarnes2910 2 күн бұрын
I completely agree
@bustinyanutz4195
@bustinyanutz4195 2 күн бұрын
You're not old they just don't work on old enough cars, I'm 51yrs old and I know it's a voltage regulator, as a matter of fact I could've told you that was a voltage regulator in the 80's when I started working on cars with my dad
@donaldsullivan6979
@donaldsullivan6979 15 сағат бұрын
What I did with my 57 wagon when the rear shockwaves interfered with the wagon tank was relocate the tank to the non wagon location which just means cutting out the spare tire well and use a higher capacity non wagon tank and can still use the hidden gas door. The spare tire well is dead space anyways as far as the undercarriage is concerned, may as well use it!
@jefscoupe32
@jefscoupe32 12 сағат бұрын
My car was an ex drag car that had been redone back to street mode. The spare tire well was cut out (evidence of a fuel cell had been there) and I spent time and $$ to replace it. I want to have a spare and there is room for a jack and other smalls. I went ahead and did mini tubs, spring pockets, shock bar and an F9 rear while I was in there. Oh and the tailgate retractors and un-glued the rear side windows so they would operate again. Took me about a year and a trip to Colorado to get the parts and do the work. Lol
@TK-fp5fp
@TK-fp5fp 2 күн бұрын
That’s just amazing, I’m so glad that car was won by a guy who’s going to take it to the next level. Hopefully you’ll keep in touch with him and post a couple of updates so we can see the awesome car you inspired.
@kevinhornbuckle
@kevinhornbuckle 2 күн бұрын
That would be interesting.
@mambastu
@mambastu 2 күн бұрын
I've been using push on type AN fittings for years on EFI fuel, water and oil hoses. I always use an Aeroquip high pressure push on designed hose with Ebay (Torques) push on aluminium fittings which have the multiple barbs. With assembly I make everything off the car and use a nylon fittings clamp to hold the alloy fitting in a bench vice and then dip the hose end in a mug of boiling or near boiling water for five minutes to soften up and expand the end of the hose before pushing it on the end of the barbed fitting. I don't use a lubricant other than the water in the mug and I don't use external hose clips and have never had a hose failure. Very easy and budget friendly method to make hoses. To get the fittings out to re-use them you need to cut down the length of the hose on the outside of the fitting as once they're in you can't pull them out.
@EdwardDean-z4f
@EdwardDean-z4f 2 күн бұрын
I still have the original 265 in my 55 Bel-Air and Powerglide. Congratulations to the winners!
@Czechbound
@Czechbound 2 күн бұрын
*That's tantastic !* Congrats to Stephen, I wish him lots of safe miles in his new machine. I agree ; he sounds like the perfect winner. I hope he keeps it and races it for years, and years, and years. Happy New Year everyone and greetings from Prague, CZ. PS : Well done Wirecare for supporting this project.
@Xjeepguy
@Xjeepguy 2 күн бұрын
Good tip about anti-sieze on spark plugs, except on NGK spark plugs. The plating on the shell is designed to be used dry. Using anti-sieze on NGK plugs can cause an over-torque situation. On all other brands though, definitely use anti seize.
@Hillbillygarage1215
@Hillbillygarage1215 2 күн бұрын
Over torque a spark plug? Do you really torque them? Spark plugs only need to be "goodnsnug"
@Xjeepguy
@Xjeepguy 2 күн бұрын
@Hillbillygarage1215 there are actual guidelines to seating spark plugs, some use them, some don't. I work for NGK, and just thought I'd share this bit of info.
@spikedmotorsport
@spikedmotorsport Күн бұрын
I can vouch for this info. I came here to say the exact same thing, as another NGK (Niterra) employee 😂
@Xjeepguy
@Xjeepguy 21 сағат бұрын
@@spikedmotorsport it's still difficult to remember the new name. 🤣
@Hillbillygarage1215
@Hillbillygarage1215 17 сағат бұрын
​@spikedmotorsport I don't dispute that a torque spec/procedure exists. Im just saying its useless and I've never worried about it. 50 years and I've never stripped one, nor ever had one blow out. So y'all go ahead and get the torque wrench out and I'll go ahead and put the plug wires on.
@eliteman7685
@eliteman7685 2 күн бұрын
I’ve been using Fragola pushlock fittings for a while now. Main thing is using the correct hose. For fuel hose, using a SAE30R9 spec hose from Continental/Contitech (formerly Goodyear hose division). I’ve just dipped in a bit of type F and yes, 3/8” fittings suck to do at times lol but it can be done by hand. I bought a reel of the hose once I got a short piece because I figured a 25’ reel is way cheaper per foot than a damn parts store that sells it for EFI hose and it’s $10-$12 a damn foot. Every time I’ve had problems, it was my own stupidity not lubing it up before slamming it on that hole. Much like all those tender dates years back 😂
@Knockonwood4643
@Knockonwood4643 12 сағат бұрын
The list! I've been there. Thinking I don't need a list because I'm going to jam right through my project with no interruption. Fast forward a few months later and I'm buying parts again that I already had because I didn't remember buying them in the first place. BTW, a piece of glass works great too for a dry erase list.
@todddaniel5642
@todddaniel5642 2 күн бұрын
For the master cylinder upgrade on a trifive, drill the two lower bolts through the center. Then install new longer grade 8 hardware, tighten the master cylinder down to hold position, and then tack weld the bolts under the dash.
@theosmit6366
@theosmit6366 Күн бұрын
Cutting the ears on that aluminum casting down leaves it with a big stress riser right where the load is the highest... and cast aluminum is not nearly as tough as cast iron. The ears on that cylinder will crack sometime down the road.
@christophercrowley6707
@christophercrowley6707 14 сағат бұрын
Windex is best for push on lube. We found doing R&D that it dries like a glue. Also hose clamps on a push fitting can create the inner core of hose to deform and create gaps over the bumps on fitting.
@KenEchols-u7c
@KenEchols-u7c 2 күн бұрын
This car is absolutely cool and your building at the right way except for that gas tank, I would have spent another few hours and just put the original tank back in it hook up the gas gauge to it but now if you think about it you're robbing the back of that station wagon of room and the spare tire, that's just my opinion but all in all you guys are doing a fantastic job
@Hitmans30a
@Hitmans30a 2 күн бұрын
Plus it's going to stink out the interior.
@benshore7357
@benshore7357 2 күн бұрын
Good times 🎉 what about brass fittings from ace hardware and some gates hose with hose clamps. That is what everyone has used forever 🎉
@rockkhound943
@rockkhound943 2 күн бұрын
Because it's incredibly unsafe
@gregpengilly2
@gregpengilly2 Күн бұрын
Hand sanitiser cleans white boards amazing. We even use it to remove graffiti around the collage. Way cheaper, and you get to keep your pressure cans for the important stuff. Hope it helps!
@NorthernHDrider
@NorthernHDrider Күн бұрын
Your videos are just great to lay back & watch a vehicle lover wrench and share how things "really" go. Have to comment about your tips. Rubber hose- boiling water helps to flex & stretch easier. Zip ties- tiny flat head to bend the locking tab. Kick butt on a happy winner!
@naughtmeenaym869
@naughtmeenaym869 2 күн бұрын
I'm only 50 but I know that's a voltage regulator (solid state relay) and is a main junction. The power into the car to power the fuse block should come from the horn relay.
@claytonargo3085
@claytonargo3085 2 күн бұрын
Looks a whole lot like an old delco voltage regulator to me. #1 should be right next to the points adjustment door. HEI kept the same plug wire locations IIRC. #1 should be just off center of straight forward. The underneath plug wire routing is how Chevy did it with the old ram horn manifolds.
@Cjelliott81
@Cjelliott81 2 күн бұрын
“If I’m at the junk yard or your mom’s house…” totally deadpan without skipping a beat. This is why you’re the GOAT. 😂
@NEILHADSALL
@NEILHADSALL 2 күн бұрын
I choked on my coffee on that one. Lol
@rockkhound943
@rockkhound943 2 күн бұрын
Im still rolling 😂😂😂
@kev90sc
@kev90sc Күн бұрын
I came here to say this. I actually rewound it and had to listen to it again..😂
@Hillbillygarage1215
@Hillbillygarage1215 2 күн бұрын
At Hillbilly Garage we knocked the porcelain and electrode out of the center of an old spark plug then taped a finger from a rubber around it thread it in the hole and turn the motor over. As long,as you have compression it will be very evident when she come up on compression
@JackWilson327
@JackWilson327 2 күн бұрын
Soooo happy to see someone who does this a lot having all the screw ball part mismatch issues I have! Gives me hope man! Thanks for sharing the crap that goes wrong leading to success.
@Shadetreetrifive
@Shadetreetrifive 2 күн бұрын
The fittings you needed for that gas line has an aluminum feral. I am using that line on my 55
@Thecleananunseenteam
@Thecleananunseenteam 2 күн бұрын
Yup the wire was most definitely for the old charging system and that's why so many people went to a one wire alternator because them old boxes would start causing problems 💯🏁🇺🇲
@montanamountainman
@montanamountainman 2 күн бұрын
Ah man that kinda sucks. The fuel door on a 57 is one of the coolest features plus looks kind of a pain to fill and the constant smell of fuel. Still a cool ride
@paulshannon4576
@paulshannon4576 2 күн бұрын
I like the wire tie holder but I also have a lot of PVC pipe around the garage so I’ll just make one. Reusable wire tie, I would take the end of another wire tie and slip it in to release the tab. I’ll try the pliers thing next time.
@skinanbonesOG
@skinanbonesOG 2 күн бұрын
someone doing the afternoon walk of shame at 48 minutes
@kevinkruegar6802
@kevinkruegar6802 2 күн бұрын
😂😂😂😂
@Derkenblosh2
@Derkenblosh2 2 күн бұрын
OMG... That's priceless
@matthewkingsmore8824
@matthewkingsmore8824 2 күн бұрын
I literally ran to the comments to see who else saw it! What ya got going on over there, Mike?!
@justinspencer283
@justinspencer283 2 күн бұрын
Definitely need a explanation of that situation lmao
@sethp0411
@sethp0411 2 күн бұрын
@@justinspencer283lmao pretty funny but she had a leg brace
@stco2426
@stco2426 2 күн бұрын
Really enjoyed this and I didn't even enter. Great to see the '57 come to life and it'll be good to see the handover / new owner and for you us all to see the exploits.
@timtaylor6147
@timtaylor6147 2 күн бұрын
Saw you cutting the Master cylinder On my 55 Dodge The master cylinder for a 71 Dart fits perfectly Thought after scratching my head for a while realized the pushrod length was wrong I looked at it Then remove the thick rubber pedal stop and the master cylinder was able to fully return to rest position The brake would progressively lock upon front I had done the swap to replace the single reservoir stock brake master
@G60syncro
@G60syncro Күн бұрын
At the shop I work at, every hose and hard line drawing has a note to purge and cap off both ends before use. That's a good habit to keep during your build!!
@OverkillAndrew.AKA-boostman
@OverkillAndrew.AKA-boostman 2 күн бұрын
I'm building a 1971 Ford Maverick grabber and I used that blue wrapped aircraft-grade fuel line with the plastic coating on the inside anyways I used the cheap push lock fittings and I feel your pain brother some of them where push lock and some of them were the thread on/ crimp.. I used to use a vice and put them together on the bench and then take the whole hose over to the car
@Wonderama2024
@Wonderama2024 Күн бұрын
Always enjoy your builds took one of your stealth hats to the Caribbean. It worked very well. Many compliments also ran into a frontiers that was helping out with your boat racing a while back in Newport Beach where I hang out keep up the good work and creating great content.
@TurboAdam
@TurboAdam 2 күн бұрын
I used Fragola push lock hole for everything on my car, but I bought the Koul Tools(sp) push lock vise and other than a couple times it was difficult to put the fitting on in the car, it worked slick as hell! Well worth the $300ish bucks for the tool!! Drop in the bucket really considering the couple grand I have just in hoses and fittings!
@wrongwaywillie1395
@wrongwaywillie1395 Күн бұрын
A day late and a dollar short, but was still stoaked to see this set of videos has I am building a 2 door 57 210 wagon gasser my self. I was just looking at woody's for a chassis before running across these vids.and always using Speedway. good luck in your future ventures. Will
@lgun1
@lgun1 2 күн бұрын
That's the wire from the voltage regulator that charges your battery.
@bolognatony8739
@bolognatony8739 2 күн бұрын
The Grob is the way ! Great nlade welder on em. The power feed is a beast for cutting thicker steel and long cuts with the cross slide.
@dianasweetpea2561
@dianasweetpea2561 2 күн бұрын
Mike! Long time fan of you and the boys! So happy to see you guys living your best life! Keep the party going!
@ArchGecko
@ArchGecko 2 күн бұрын
Ooh I like the zip tie tip. I normally use the tip of a knife or something else small to hold the tab back
@kc2giw
@kc2giw 2 күн бұрын
Wrt the saw - for those if us space constrained, I just bought an m18 portaband and the swag off-road table and my god is that a slick unit.
@deanstout1134
@deanstout1134 2 күн бұрын
Parker makes various type of hose for different fluids. If you use their hose and their fittings the push lock stuff works fantastic. I’ve used them for years.
@andybobandy641
@andybobandy641 2 күн бұрын
Here's a tip that you missed. Put a vice grip garage style Wix 33003 visible fuel filter in line just before the carburetor so you can, A: Filter the Fuel, and B: visibaly see if the fuel pump is working, and the cab is getting fed.
@fritzdixxon6071
@fritzdixxon6071 2 күн бұрын
Try writing over the words with a second coat of marker then wipe it off right away while it is wet. It even works for erasing sharpie marker
@1clnsdime1
@1clnsdime1 2 күн бұрын
So they make a small press that is made for push lock hose. They also make a lube that will dissolve. If u get those 2 items, it will work just fine and easy to do.
@erickbernard8208
@erickbernard8208 2 күн бұрын
Throwing a hotdog down a hallway 😂😂😂😂😂, that never gets old
@54inches
@54inches Күн бұрын
Unless your the hotdog.
@eiccaw
@eiccaw 2 күн бұрын
When i do any fuel lines i put earplugs through it by compressed air it cleans everything 😎
@Headsup9550
@Headsup9550 2 күн бұрын
As soon as I cut that type of fuel line, I hit the frayed part of the jacket with a torch lighter or heat gun. Then you gotta figure out if the fitting you have is reversed or std direction threads, or if it's just ribbed. I have a buddy who puts the outer nut on hose with his impact, but I'm not that brave. There's getting to be so dang many types of hose, it's getting tough to discern what you got!
@larrybeussink7737
@larrybeussink7737 2 күн бұрын
I don’t know if anyone else has mentioned it, but using needle nose pliers to stretch open hoses before pushing in fittings also works.
@sharkinstx
@sharkinstx Күн бұрын
Nice tip on the zip ties. I normally use a pocket knife to pull down the hook to release the tie. Not easy.
@FORRESTROBINSON-h5y
@FORRESTROBINSON-h5y 2 күн бұрын
Mercury power tune spray is man’s best fried when it comes to putting push lock hose together. It makes rubber crazy slick.
@wrench_n_ride8159
@wrench_n_ride8159 2 күн бұрын
You should have put the gas tank on lockable sliders so you could access the spare tire well. That way, you have more storage room for storage space for a drag and drive.
@vehdynam
@vehdynam 2 күн бұрын
Great video with some good tech tips. Gasser winner was the right guy for sure ! Thanks for the video , I always enjoy them on a Sunday morning.
@ibraunchy20-vn5kd
@ibraunchy20-vn5kd Күн бұрын
Love them tri-five wagons , just found your channel, Subbed instantly I just dont trust push lock fittings , I hose clamp everything TIP: OFF bug repellent will remove sharpie from almost everything, just wiped off a mark on my bathroom counter top with it
@Shadetreetrifive
@Shadetreetrifive 2 күн бұрын
A 74 vette with manual disc brakes master cylinder from the parts store will bolt right up without any modding.
@kh40yr
@kh40yr 2 күн бұрын
Had to trim the ears on my Danchuk dual disk master. Flap wheel to the rescue. Didn't have a deep throat bandsaw at the time, I do now. Bar soap on the band blade, no wax. Wax will make the blade slip on the drive wheels and move the tracking of the blade around. Then you have to pull it down, clean all the wax, and reassemble. You know, at the end of 1955, the first year of the Sbc, you could have ordered a 11/1 compression, Duntov solid lifter 265CI. You could have ordered the same 11/1, Duntov in the 283CI for 1956, in your Tri-5 Chevy, with 3 speed colum shift, 4 door, wagon. The Jesel Bros, of Jesel valvetrain fame, campaigned a dual carb 265ci Tri-5 delivery 2 door, and they did really good. It was called "Yoo Hoo II".
@donparisi898
@donparisi898 2 күн бұрын
I bought a hose assembly tool from Koul Tools when I was building my power steering low pressure hoses. It’s not the cheapest thing in the world but it’s not that bad and it makes putting push lock hoses a breeze
@johnsartelle8320
@johnsartelle8320 2 күн бұрын
Mechanical REGULATOR 😂 we used to adjust those so little old Lady's that only drove 5 to 10 blocks to the Grocery store, would charge the battery higher, so when they needed to go again next week it would start for them. I worked right on main street of a town with 1400 people. It was a Flying A fuel station when my Dad and Grandfather bought it in 1960 I think. Then Phillips 66. We had 8 bays and was very busy. I worked there until 88 then started doing what you are now.
@glamiskid50
@glamiskid50 2 күн бұрын
That was really cool. Definitely think the right guy won the car. Hope he shows up at Sick week so we get to see it driving Maybe he can put the motor from his Nova in it ? congratulations brother
@rockkhound943
@rockkhound943 2 күн бұрын
I prefer to plug the outlets of brake master cylinder when bench bleeding. Goes much quicker . Most all new ones come with them fir that reason.
@tonycarter8527
@tonycarter8527 2 күн бұрын
Looks like you are using Teflon hose? Can’t use it with push lock fittings. When assembling push lock fittings with correct hose, dip end of hose in break cleaner, slips right on then brake clean evaporates.
@johnjunge6989
@johnjunge6989 Күн бұрын
Had to laugh, when you was trying to locate regulator. When I was first starting out, my boss made me draw the schematic of how the regulators internal wiring worked. Plus I owned a 55 before alternators came put, everything had a regulator. 😅
@cabrini00
@cabrini00 2 күн бұрын
Somehow I get the impression that your heart wasn't really into this build?
@courier11sec
@courier11sec 2 күн бұрын
I mean it was to give away to someone who wants to build a car, so it honestly only need to work well enough to get to the person's garage.
@mando440BB
@mando440BB Күн бұрын
Finnegan:”Yeah I’d rather be racing Blasphemi!”😂
@PhilCoadSR
@PhilCoadSR 2 күн бұрын
Just watch the episode of the Gasser wagon seen you struggling with the fuel hoses little tip take some brake clean spray the hose and then install the fitting. You’d be surprised how much easier it is.
@ZspotMotorsport
@ZspotMotorsport 2 күн бұрын
I’ve always heard don’t use hose clamps with pushlock ends, because the barbs can slice the hose. 🤷‍♂️
@johnjenson5738
@johnjenson5738 2 күн бұрын
Not only you have a great place for gas tank and also weight transferz!
@imsurethisisnotme4736
@imsurethisisnotme4736 Күн бұрын
I covered my entire garage/shop walls in that sheet dry erase board. It was awesome! Great for lighting
@tysimmons2444
@tysimmons2444 Күн бұрын
The wide whites and the chrome reverse wheels are great looking
@jasonhill5985
@jasonhill5985 2 күн бұрын
Love how there are two fire extinguishers on hand. Nice to be prepared.!!
@jasonhill5985
@jasonhill5985 2 күн бұрын
Pete Harold engine😮
@EldonsService1
@EldonsService1 Күн бұрын
try putting a whistle in the end of a rubber hose and hold the hose over the plug hole. It will whistle just before it comes to tdc
@HPSFRoadrunner
@HPSFRoadrunner 2 күн бұрын
Us carpenters call that "old-growth" lumber. I was hoping you'd put matching rims and tires on the front cuz those Cokers look so damn good with the 2-tone paint.
@toney-2759
@toney-2759 2 күн бұрын
THAT'S AWESOME!! Thanks for all the great content Mike
@PiDsPagePrototypes
@PiDsPagePrototypes 2 күн бұрын
Sound like the right guy won! And ready to take it on Sick Week, Awesome!!
@robertcross7418
@robertcross7418 2 күн бұрын
Speedway Motors has a really good tool for Push lock fittings!
@clarkdoukas3477
@clarkdoukas3477 2 күн бұрын
Heat the hose hot, gloves, and the push lok fitting will glide in
@knight8563
@knight8563 2 күн бұрын
Warming hose ends in boiled water for a minute or two will help a lot as well, surely there is a fuel cell that would fit n fill the spare wheel tub?
@dfox7777
@dfox7777 Күн бұрын
Hers a weird tip for your dry erase board, if what you wrote is old and won't wipe off, just draw a blob over it with a new marker and it will all wipe off!
@Doubie.
@Doubie. 2 күн бұрын
Mike take the magic marker and scribble over the dried up ink on the white board then wipe it off it rehydrates the ink then you can wipe it off like normal
@SteveP-vm1uc
@SteveP-vm1uc 2 күн бұрын
Tip: Before pulling the distributor for paint, bring the engine to TDC @ #1. If you allllways do this, you will never wonder or have to mess around. You probably could have put the correct tamk into it with all of the screwing around..
@TheJustintyper
@TheJustintyper 2 күн бұрын
Exactly! And now whoever works on this next will wonder/have to figure out how the wires are run/where number 1 is. 😊
@mcjok88
@mcjok88 2 күн бұрын
Re the hose connection... HEATGUN, DRIFT AND LUBE.
@Bob0sModelFabWorx
@Bob0sModelFabWorx 2 күн бұрын
Here's a Pro tip for you! on the end of the hose you enlarged, you can use a screw hose clamp on the end to close it up before you put a fitting in it.
@SpiveyNatas
@SpiveyNatas 2 күн бұрын
Congratulations to all the winners. Sick Week is going to be epic!!
@The_sinner_Jim_Whitney
@The_sinner_Jim_Whitney 2 күн бұрын
22:15 Scotch Super 33+? The greatest electrical tape in the history of electric, or tape?! Man, you do things RIGHT...
@jkK-lw9lu
@jkK-lw9lu 2 күн бұрын
All of the”push-lock” hose I’ve used says “ Goodyear push-lock” on it, if it doesn’t have the label, I use a hose clamp. There’s a tool to push the fitting into the hose, and a little heat helps make it easier (too much heat makes it as miserable as too little!) for the balance between labor and parts, screw together makes more sense!
@jeffreyhyder2429
@jeffreyhyder2429 2 күн бұрын
PARKER push-lock hose and fittings have always worked great for me. It’s fine for oil and coolant but I don’t think it’s comparable with modern gas with ethanol.
@OGRocker1
@OGRocker1 2 күн бұрын
Mornin Finn, Good morning gearheads... Sunday, Sunday, Sunday and a Happy New Year🔥
@FrankF-vp4pt
@FrankF-vp4pt Күн бұрын
Caught my eye with that stock looking small block . New subscriber.
@666thsense
@666thsense 2 күн бұрын
you could also get shouldered nuts and widen the holes in the master cyclinder
@larrylucas5731
@larrylucas5731 2 күн бұрын
Well, I guess I should have watched the whole video. Better luck next time!
@Grumpy_Stiltskin
@Grumpy_Stiltskin 2 күн бұрын
It will be on marketplace next week.
@trevorposey7109
@trevorposey7109 2 күн бұрын
I won the 2nd place prize. The Chevy was won by a local in Augusta according to his IG post. If it does end up on the marketplace it will be after Sick Week as the winner wants to bring it there.
@AsswipeGarage
@AsswipeGarage 2 күн бұрын
​@@trevorposey7109A LOCAL won it?? Sounds fishy to me. Saves Mike a fortune on shipping.
@guidorollard2944
@guidorollard2944 2 күн бұрын
good chance it will be
@trevorposey7109
@trevorposey7109 2 күн бұрын
@guidorollard2944 after listening to him, quite possibly, to fund his current Nova build.
@andhotrodshop
@andhotrodshop Күн бұрын
How about the pan head screws holding the timing cover on. Most of those got thrown away and replaced with hex head bolts. Only the early sbc had pan screws. 🙌🏼👍🏻👊🏼🔧🔧🔧🔧
@biglakehotrods381
@biglakehotrods381 Күн бұрын
That’s cool that a local to me guy got it. Hope to see it around. Congrats to the winner!
@scottlagasse3182
@scottlagasse3182 2 күн бұрын
I’ve used Push-Lok hose for over 25 years with no issues. Parker hose and fittings.
@ryurc3033
@ryurc3033 2 күн бұрын
Big pass on push lock. Go into any parts store anywhere and they look at you like you have crabs crawling out of your ears when you ask for push lock hose. One guy at O'Reilly even told me, just use regular 3/8 gates low pressure hose ....for a fuel injection application with push lock fittings.....if its uncommon, im avoiding it.
@051570orion
@051570orion 2 күн бұрын
On a dry erase board , if it won't erase , use the marker and write over what didn't erase and it will wipe off after you do that
@tlr_shenanigans
@tlr_shenanigans 17 сағат бұрын
44:27 brother that tip right there will take you far in life even outside of hot rods 😂
@sharkinstx
@sharkinstx Күн бұрын
That’s the voltage regulator on the back of the core support. Classic three-terminal voltage regulator.
@jimk351c
@jimk351c 2 күн бұрын
To clean the white board trace over the old dry erase marker with a fresh one, then simply wife off.
@mobiousenigma
@mobiousenigma 2 күн бұрын
mike thanks for the videos..for your whiteboard list according to kevin of junkyard builds a little sunscreen lotion will take it right off...
@courier11sec
@courier11sec 2 күн бұрын
Baffled that you didn't stab the distributor in properly instead of moving the wires all around. 😆 Thanks for that nugget about squeezing zip ties that I somehow didn't know. 😺
@stevevanpatten1372
@stevevanpatten1372 2 күн бұрын
Mike Finnegan please keep making more Video's of your Building. ❤❤❤❤
@davidechols6797
@davidechols6797 2 күн бұрын
Hey Finnegan, should be a 283. A 265 didn't have a oil filter boss on the block. Love the car awesome.too bad I didn't win LOL
@davidwatching9594
@davidwatching9594 2 күн бұрын
Hey Mike I’ve used rubbing alcohol on hose fittings for ever. I’ve never had an issue. Give it a try.
@timburns5025
@timburns5025 2 күн бұрын
Welp, I hope I win, but I don't like the modification been done, dist, brake booster. But very nice on everything else. And a heater would be nice too!or more of a street rod. Rather than grandma's race car from the past. All tho, very nice.😮
@Ellington_Industrial_Arts
@Ellington_Industrial_Arts 2 күн бұрын
I use the same large dry erase trick to keep track of my projects too. A tech tip, from me to you... when you've ignored a project long enough, that the dry erase doesn't want to come off the board... a magic eraser pad, soaked in rubbing alcohol, will clean up the residue and make it nice and white again. So you can write up the list, for the next project, that is also going to be ignored, until you're forced to address it. 😂
VIP ACCESS
00:47
Natan por Aí
Рет қаралды 30 МЛН
Леон киллер и Оля Полякова 😹
00:42
Канал Смеха
Рет қаралды 4,7 МЛН
This is the ULTIMATE Axle for The Race Jeep!!!
27:09
Rudys Adventure and Design
Рет қаралды 56 М.
Our No Prep 4x4 NASCAR Truck Makes INSANE Runs!!
31:25
Cleetus McFarland
Рет қаралды 1 МЛН
Building a Hot Tub on Snow Tracks Might Be My Best Idea Ever!
27:31
HeavyDSparks
Рет қаралды 451 М.
DIY CHEAP Classic Truck Interior Restoration and New (vintage) Wheels!
1:53:01
Q&A With DULCICH and FREIBURGER from Roadkill Garage
55:20
David Freiburger
Рет қаралды 280 М.
Can we Fix-Up an old Square Body on a REAL BUDGET??
51:03
Junkyard Digs
Рет қаралды 579 М.
My Customer Is Getting Shafted By The Local Toyota Dealer
32:04
South Main Auto LLC
Рет қаралды 139 М.