Overall I really enjoyed the video, but I disagree with the comments at 6:11 around the water cocks. The FRA promotes the use of sight glasses as the more accurate means of showing water level with gauge cocks a backup means. Not only are you able to visibly read the levels at all times via the glass, boiler investigations from as far back as the 1920's confirmed that the backhead is subject to a water surge phenomenon while underway which can give a higher reading through the gauge cocks. A properly maintained and blown out water glass will give the best reading as water will always seek its own level. Plus I generally find reassurance in visually seeing the water at all times considering just how safety-critical it is.
@Hyce7772 жыл бұрын
Must have been the old heads that taught us on the narrow gauge going slow with those staunch opinions i suppose, haha. We do use the sight glasses 99% of the time. Pinning your comment for visibility.
@TheRoadburner992 жыл бұрын
@@Hyce777 hey Hyce if you were firing a coal burning standard Gauge steam locomotive from coffeville Kansas to Paola Kansas and the locomotive is a Santa Fe 484 Northern type would you be hand firing such a locomotive or would it be using a stoker and you were a helper engine on a modern freight train and you have an auxiliary tender how much coal and water would you need to get to Paola Kansas?
@jackx43112 жыл бұрын
Have to say I much prefer having a sight glass. If the water is bobbing up and down, you know all the connecting tubes are clear. If the water level in the sight glass stops bobbing, you know at least one tube is blocked. You don't have to open a try valve to check - you can not only see the level over the firebox crown, but also see that your water glass is giving you a true reading, just by glancing at it all the time you're working.
@Hyce7772 жыл бұрын
@@jackx4311 I agree, I prefer the sight glass - was just always taught that the trycocks were the end-all-be-all. Apparently in narrow gauge land and nowhere else, lol!
@shaynewheeler92492 жыл бұрын
Coal fired steamship Titanic
@Tultry2 жыл бұрын
Thank you for explaining what the fireman does! The GoPros captured everything beautifully despite the fire threatening to melt them. Well done!
@MrNeterix2 жыл бұрын
The intro of this video is absolutely fantastic. Also good job with explaining how all of this works without confusing everyone.
@chiftelgaming7983 Жыл бұрын
whats the song in the intro if you know?
@sambrown64262 жыл бұрын
Yes, please do make a video on all the ways a steam locomotive can fail spectacularly, or maybe you could tell us all the ways the Back to the Future train scene was unrealistic. I'd watch both of those videos.
@blackoak4978 Жыл бұрын
Worst case scenario, look up B.L.E.V.E
@sambrown6426 Жыл бұрын
@@blackoak4978 Ok.
@RC-bm9so2 жыл бұрын
Tonight on Top Gear: Colorado Railroad Museum Edition: Hyce continues to laugh like a hyena and starts a new line of shampoo: D&RG Fresh Mountain Air, Jeff sees his darkest fears, and D&RG 491 decides to unleash her fury against Double Farlies with a steam blowdown along the road. Also, love the content, glad to be a part of the channel.
@Hyce7772 жыл бұрын
Thanks for being a part, RC :)
@trainsandcrossings79682 жыл бұрын
I'm starting as a fireman student (learning to become a fireman) this year here in Sweden, these videos you make are amazing and really help out a lot for me both with narowgauge (891mm) and normal gauge (1435mm), i love learning about these beautiful machines, they have a simple princip but they are packed with technologie and power.
@ethanlarribeau59592 жыл бұрын
This deserves way more views than it has. It’s honestly my favorite video on the channel.
@Hyce7772 жыл бұрын
I was hoping the coal scoop thumbnail would gain clicks, but I guess not. Glad you enjoy it!
@Darkenrall12 жыл бұрын
I've always been passionate about steam locomotives, since I was a child, but here in Brazil there aren't many places you can go to see these engineering beauties!!! One day I will see… one day… meanwhile, it was a delight to watch this tour, thank you!!!
@frederickjunctionproductio97523 ай бұрын
Great video! I'm a Volunteer out of a Railroad in Maryland. Your not wrong You gotta treat the steam engine right. My Saying is "You treat the Steam Engine right she will treat you right" Keep up the awesome videos!
@Cougar063 Жыл бұрын
Damn, as someone not really experienced how all this stream locomotive thing works, this was truly an insight. The things you have to know and be able to do both mentally and physically to get one of them beasts going is astounding! Mad respect to you and all the other engineers / firemen out there. And you explained stuff really well, was fun to watch. Thanks for all your effort. Is always fun to see someone who enjoys their job!
@Mildcat7432 жыл бұрын
Man, ShovelCam is so cool. Watching those big smooth windup throws to bomb the back of 491's fire is so satisfying.
@TandemDawgBMG2 жыл бұрын
42:40 Anthracite coal is basically "big power" coal. High carbon density, and very pure. Very hard to ignite but it burns long and clean, requires a lot of heat and a big draft to burn, so mostly when the locomotive is working. We had a ride-on Reading A5 camelback with a Wootten firebox, started on Charcoal, then moved to bituminous until the fire burned nice and even, then you could start mixing in Anthracite. You really want to work with small size Anthracite to take advantage of as much surface area as possible to get it to burn.
@PowerTrain611 Жыл бұрын
Unfortunately, it is very hard to find good quality anthracite in the US these days, especially at a good price. The CNJ 113 runs on basically a 50-50 mix of bituminous and anthracite for this very reason!
@jaysmith1408 Жыл бұрын
Our area, we have anthracite literally sitting on top of the ground. It’s absolutely everywhere. Put some in the fireplace, didn’t have to stoke it for over a day.
@Jaffacall325111 ай бұрын
@@PowerTrain611 CNJ 113 is located in the middle of the largest anthracite fields in the world.
@PowerTrain61111 ай бұрын
@@Jaffacall3251 Ironic, isn't it?
@GarageBandSuperheros Жыл бұрын
I just watched an hour long video of a guy showing me how an old TV switch mixer works. Now I'm watching a hour long video on how to shovel coal into a steam train. I'm on a roll tonight, why are these super niche hobbies sooo interesting to me all of a sudden. Great video. I think I have another new hobby. TRAINS! :)
@Hyce777 Жыл бұрын
Glad you enjoyed :)
@blackoak4978 Жыл бұрын
Your videos are really showing me how our power engineering has moved on the stability curve. Steam engines are almost the definition of the peak of instability, with both the high end and the low end leading to catastrophic failure. Meanwhile cutting edge nuclear reactor designs are at the bottom of the stability valley with the laws of physics maintaining that stability
@Hyce777 Жыл бұрын
Definitely true - steam in this era really wasn't stable.
@daviddryden80882 жыл бұрын
I can see why the museum hired you. You are smart. That was easily the best hour I've had on YT in days.
@Hyce7772 жыл бұрын
Cheers David! I appreciate that :)
@Tristan_S3462 жыл бұрын
Gotta love that Intro Song ;)
@ajaxengineco2 жыл бұрын
Anthracite coal is best with a strong draft, a deep firebox, and it helps to break it up - if you put a football sized piece in a small firebox its gonna sit there forever if you aren't working hard and if you are then it'll turn into a meteorite and you'll begin blowing off. Like furnace coke really. The Welsh stuff, which for all of industrial history was favoured by steamship captains and British railway companies, especially the Great Western, has a very high calorific value and low sulphur. It doesn't produce much smoke (as long as you have a brick-arch) and when its been in long enough to ignite it doesn't burn so much as glow white-hot. Smaller tank engines on branch lines (little 0-4-2Ts with 5'6" drivers pulling one or two coaches) like a saucer-shaped fire with high front corners - you can almost have lost the back corners by the end of the day and you'll make it home just right. On a big engine (such as a Great Western 'King' with six 6'6" drivers) you want it built right up to the firedoor before starting and if you keep it going right you'll have steam in hand the whole length of the journey. The 'King' class was the last and largest of the Great Western Railway's express types - you wouldn't want to get knocked down by one! The strength of exhaust blast needed is best epitomised by the much smaller 'Manor' class - have a listen to one while working - tis quite a noise. They weren't actually all that when built, the blast-pipe nozzle was narrowed after a few years and they were much improved. As all the 'big' Great Western passenger engines were 4-6-0s, they were expectedly smart when getting away with a load - all the weight would be upon the driving wheels (they tried to do a Pacific once - it had a wide firebox and was expectedly a failure.)
@Hyce7772 жыл бұрын
Cheers for the details on those locos, that's awesome.
@Leatherface123.2 жыл бұрын
I was able to understand the first few sentences until you got to football, after that I had a stroke so big it killed several people in my neighborhood
@andrewdonohue1853 Жыл бұрын
i heat my home with anthracite. it burns long, steady, and cleanly. it is very different then bit coal.
@AShadowboxsFSX2 жыл бұрын
Hey Hyce you probably already know this but just want to say if you're hand firing any kind of locomotive or working in any capacity where your clothes get sooty make sure they get washed promptly and separately from other clothes. The carcinogens in the soot are a huge cause of cancer and you don't want that crap getting on your other clothes, or around your house. You also don't want to "rewear" dirty work clothes because that drastically increases your exposure. Also if your skin gets sooty or you smell like smoke you want to shower as soon as you can, for the same reason. This has been fire tips from a firefighter ("fireman" haha), thanks for tuning in
@Hyce7772 жыл бұрын
Cheers mate! Didn't have the details of all that. Good to know there's more a reason to be clean :)
@Bustavegas2 жыл бұрын
I'm a conductor with BNSF Railway.. Been with the company almost 15 years.. I couldn't imagine doing this back in the day.. Cool Video!
@mechanicalbird2822 жыл бұрын
This intro is awesome, the footage and the music go so well together
@duckosoup39942 жыл бұрын
Thank you for continuing this series. I love the intro, some music to fit the mood with some good camera angles really makes this good result.
@Idaho-Cowboy2 жыл бұрын
Love it! So cool to see. Kudos to the museum for letting you get all this footage.
@Scot-i1p6 ай бұрын
My great-grandfather was a fireman 100 years ago. Seeing this video really helped me appreciate the skills he had to have. Later, he moved to Pontiac to work in a car factory. He was still a fireman there, too. I'm not sure how that was in a factory. Anyway, thanks for the informative video.
@bpark100012 жыл бұрын
You mentioned using sunglasses to view the fire. You might want to try Enchroma CX3 sunglasses (intended for the colorblind). They have an absorption bend in the yellow, allowing you to see "through" the yellow flames to the coal below. They also intensify color (even for the normal-sighted to see subtleties). Another type of glass to use is glassblower's "didymium" glasses. They also absorb the yellow glare.
@Hyce7772 жыл бұрын
Huh, that's something I've not heard about. I'll have to give those a shot!n
@aaronlevering31582 жыл бұрын
At the railroad I get to run steam locomotives at the engineer and fireman positions are combined somewhat. They are oil- burning engines, so it isn't so bad, but the fireman just puts water into the boiler and does the blowdown. Also, Hyce I definitely appreciate the grade changes on the water level. At one of our stops, we are pointing uphill and at the other downhill. It is a rollercoaster railroad. Great video
@Armageddon_712 жыл бұрын
Wow. I shed a tear at that intro!
@jackx43112 жыл бұрын
One of the things I found hardest to get right was aiming the coal to get it EXACTLY where it was needed - especially on those USATC 0-6-0 switchers. Instead of having double sliding doors like most British locos used, they have a circular swivelling flap which makes really awkward to get a decent sized shovel through the stupidly small gap with a nice smooth swing to reach the front corners of the grate. As well as being a pretty large grate for such a small engine, it's very shallow, too. And having most of the firebox inside the cab, on hot humid days - a killer. A friend who was rostered to fire one of them in a particularly hot spell in late July sweated off half a stone (7 lbs) in a week, and told the roster clerk "Never again!"
@PowerTrain6112 жыл бұрын
Great video, awesome explanations of everything. From my experience, it's always good to get into a pattern. Shovel on the coal, take a seat, check the surrounding area out the window, check your water level and add as needed, repeat. I also worked on a 3 foot gauge circle, so in our cases it is much easier get that pattern going. It's a real lost art! As soon as you mentioned the air brake problem with the older brake system, I knew it was an overcharge. Always gotta remember to leave it in the running position with the 8, 6 and A valves!
@Hyce7772 жыл бұрын
Yup! Engineer is used to an H6 and we had the G6. No detent to separate overcharge and running - easy mistake to make if you're not familiar.
@PowerTrain6112 жыл бұрын
@@Hyce777 It's the devil in the details. The smallest difference can make for a huge pain.
@Aidan_Rattlehead2 жыл бұрын
Please make more of these types of videos, that was amazing.
@alwaysbearded12 жыл бұрын
I don't fire any engines but still think I understand the basic concepts of constant watching and observing and planning ahead as was common in a lot of work back in the day and is lost to most of us today. With everything digital handed to us on a silver platter instantly we don't tend to think 5-10-15 minuets or hours in advance. I observe that the fireman is really the engineer and the engineer who is running the engine. The engineer is more of a driver but still has to be thinking ahead. My own similar experience is sailing. You are constantly evaluating, observing, thinking of everything including contingency plans and thinking varying times into the future for different actions you will need to take. I also have done lots of cooking on large wood burning stoves (actually one was designed for coal but we were not allowed to use it for environmental reasons). It is an art all the same reasons, things are not instant, you have to think ahead, maintain the fire and supply chain (did you bring enough wood/water/food from the shed to the ship where the stove is for the meal...) Thanks for the 101 series. I may yet work on a RR when I retire. Too many irons in the fire right now.
@philismenko2 жыл бұрын
Great grandad was a fireman for the n&w and worked on some of the 6xx series(not 611, he was on the cavalier not the Powhatan arrow) so its cool to see what he did
@terrytait282 жыл бұрын
This is a great review of how to hand fire a steam locomotive. It was more difficult when I volunteered there because the track was not a full loop. We’d load passengers at Delay Junction and go up the hill and stop at No Agua Tank to unload/re- load. So you’d get to the top with a nice hot fire and then stop. Found myself with too much fire AND water a couple of times but I was a rookie that wasn’t there very long and we only ran steam 3 or 4 times a year if I remember correctly. The fireman side injector on 346 was picky and it usually took me 2 or 3 try’s to get it to start. If there were videos of me firing it would show me incessantly blowing down the sight glass to check water level.😀 I really enjoyed the challenge of balancing everything to keep proper pressure and water level.
@Hyce7772 жыл бұрын
I can only imagine how annoying it was to fire pre-circle, and - fun fact, that injector is still cantankerous.
@vornamenachname7272 жыл бұрын
20:38 On german locomotives, the blowdown sits at the very bottom of the boiler below the locomotive. It is called "Abschlammer", because it´s there to get rid of all the impurities ("Schlamm") in the water.
@michagrill94322 жыл бұрын
Yes its literally a blowdown :P
@cjevick58612 жыл бұрын
thank you for this hyce
@unclewilly2 Жыл бұрын
I once had the amazing opportunity, to co maintain and operate a little steam vessle for the course of roughly 2 years, not that long ago. And once even operate it mainly alone for 2 whole days on a steam event. I loved it so much, never had a 10 our day rush past this fast! That little thing was such a hand full to operate. Im getting flashbacks seeing you fire the 20. Love it. I vividly remeber the condensed water from the wistle sprinkling my face, i really miss it. 😄
@Tristan_S3462 жыл бұрын
"Fire Stoker Jobs are NOT For the Faint of Heart"
@J.R.in_WV Жыл бұрын
As soon as I read this I heard a narrator’s voice in my head from a game I knew I played as a kid….after a quick google search it all came back to me….Lionel Train town!!! I remember how the trains would run off one side of the map only to come back on the other and cause all kinds of havoc if you were moving another train and didn’t have the switches set right.
@l-jpersson75322 жыл бұрын
I'm an engineer and ofcource I started as a fireman on our narrowgauge in Sweden. And in Sweden the fireman i positioned on the right, We run on coal and have 4 locos in different state of repair, and a a fifth that is running as our main engine. We even have the only excisting loco outside of UK that is made by Fletcher and Jennings in the UK.
@EtzEchad2 жыл бұрын
I've heard it said that people used to be able to tell which engineer is driving the train by the way he blows the whistle. I can really see how that could be true. I LOVE steam whistles!
@BillSteinhauser Жыл бұрын
Glad to see you explain details of how to read the fire, and stoke coal evenly across the fire box, allowing for even heat+ airflow... plus importance of planning steam/burn rate in advance for the upcoming grade & amount of work+steam the engine will need over the next 10-30 min... You may also discuss timing aspects of water injection, how it would certainly be needed before a long pull, but will cool your boiler in the short term... so it needs to happen well in advance, giving you time to rebuild a strong head of steam. A long pull will also mean that the loco+boiler is pointed Up hill a few degrees, which gives you a few more inches of water covering the top of fire box at back of boiler. (and level in sight glass goes up, even though total water in boiler did not increase) Working freight steamers in 1940s still need to inject some water on a long upgrade even though the sight glass shows full (knowing you are still using lots of steam, and front of boiler has less water) Once you reach the Top of a long grade, you are working with a hot fire and depleted boiler... The Loco will level off and may start to point down hill. They may still have 100+ rail cars behind them to pull up the hill and over the top, but now water in the boiler flows toward the Front of the boiler, leaving Low water over a hot firebox/crown sheet. (can lead to a dangerous situation in just a few minutes, unless thinking ahead) With longer working trains, it was possible for locomotive to make it over top of hill, be pointed downhill, but low on steam and stall with weight of 3/4 of the cars that were still on back side of hill. Please keep explaining as much detail as you can about the knowlege, planning, efforts needed to properly operate steam trains in the past. 😊
@pebsymax91132 жыл бұрын
I'm a fire starter in the UK so have been learning the art of firing and realise how hard it is to shovel
@CaptainS0305 Жыл бұрын
Coal shovel cam is always a really cool view of the fire in the firebox
@shawnhuk2 жыл бұрын
Quite enjoy these videos. As a carpenter and machinist, I don’t do anything with steam or trains, but I’m enjoying the videos.
@3900Class2 жыл бұрын
I've been a fireman on the Black Hills Central Railroad for about a week now. While the coal stuff isn't as applicable to our engines, the water stuff is really similar to what we do. It's amazing learning how all these concepts apply to what we do.
@Hyce7772 жыл бұрын
It really is, isn't it?
@mikehogan92652 жыл бұрын
When you first start firing engines you think you just chuck in the coal and that's it. My experience was with South African steam engines in the 70's. I remember with S2 class engines you fired the coal along the sides in a dish type pattern. 14 R class engines you fired towards the back and the draft sucked the coal forward. I had a fair amount of experience on H2s and a limited amount on GO's and GMAM Garratt engines, some of which had mechanical firers and I needed assistance from the drivers who were familiar with these systems. This wasn't a career for me. I worked to save for university and did a full year first followed by two 3 month stints over the university summer holidays. Never regret it!
@mason-wr1weАй бұрын
The intro is fire 🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🏞🏞
@tophatman18342 жыл бұрын
Awsome intro and I find it informational
@geiger212 жыл бұрын
Man... I just needed someone to make an hour long video talking about steam locomotives. Thank you for that! Subscribing without a second thought!
@absoluteblockproduction20392 жыл бұрын
really cool to see the 20 in full operation after having spent time working on it at the burg in 2018/2019. Great videos!
@Hyce7772 жыл бұрын
Cheers, thanks for doing the work :)
@strasburgrailfan902 жыл бұрын
Those intro shots are amazing! Hope to see more like those in the future
@hadinossanosam44592 жыл бұрын
42:42 Another similarity between 491 and a cat: don't like being fed anything except what they're used to xD
@johniacono3725 Жыл бұрын
Thank you for this wonderful video. I am reliving my days as a steam locomotive fireman on the Valley RR in Conn. I fired four different engines . One engine the 40 was not superheated and used a lot of coal and. Water. I enjoyed my time there and some days were easy and other days it was difficult. Sometimes we had good coal and other time it was mostly fines. Never had baseball sized coal.. I am 83 now and i stopped firing in 1994. I do miss it but physically I can’t do it any more. In addition, at the Valley the fireman was the head end brakeman and we had to cut the engine off at Deep river and run around the train running in reverse all the way back to Essex. Some days it was very hot and the most difficult time I had was when the temperature went way below freezing . The water froze everywhere it was difficult but I miss those days. I must be crazy or just a die hard railroader.
@SternLX2 жыл бұрын
Heh.. that was pretty cool with the Firing 20 coaching part. When she was chuffing hard you can see the draft in the box tugging on the fire door in time with the cylinder chuffs. 👍
@Hyce7772 жыл бұрын
Right? The draft is pretty impressive.
@sawspitfire4222 жыл бұрын
This is amazing, I've learnt so many things I've always wanted to know thanks to you! So glad I found your channel By the way, if radiated heat is killing your gopros maybe try wrapping them in aluminium foil. Might reflect enough of it to keep them alive longer :)
@Hyce7772 жыл бұрын
That, among a few other case options are on my list of things to try. :) thanks
@jaredstafford33542 жыл бұрын
The Audio of the Locomotive working is really really great
@bow-tiedengineer4453 Жыл бұрын
This video made me realize how much I want the K37 in RRO. Not only is it big and powerful, but that cab is awesome. The deckless engines just feel so cramped in first person, and I've binned trains because I had to turn my camera so far back to get at the brakes, and couldn't get to it fast enough.
@blackhawks81H Жыл бұрын
As someone who's been a structural firefighter for ages, and therefore quite good at reading fire, what it's doing, what it's going to do, etc. This is something I definitely have to try before I die.. Now to find a coal fired historical railroad that isn't 20 hours away...
@TheOklahomaHotrail Жыл бұрын
To be honest, this should be used as training videos for new fireman. Gotta love details details details. Amazing video Mark
@sycamorevalleyshops28412 жыл бұрын
Thanks for adding the water level checks at the beginning:)
@Hyce7772 жыл бұрын
Ya only make that mistake on a video once, hahaha
@farmdog932 жыл бұрын
Love the videos bub, been a huge train buff since I grew up in Sugarcreek Ohio on the Ohio central, and watching your vidys has made me join the fort wane railroad society and start volunteering this winter, happy forth 🇺🇸🤘
@Hyce7772 жыл бұрын
Cheers mate! Much appreciated, happy 4th :)
@kainhall2 жыл бұрын
54:58 that is a PERFECT example of how the exhaust draft works . fire goes from 0 to 100 back to 0 REALLY quick at low speed LOL
@Waldbahner2 жыл бұрын
so glad to see you back on CRRM... you're not only a steam loco engineer/driver/fireman - you're actually "steam"... I didn't had the oppertunity to operate the real stuff a lot (just here and there a couple of times) but I enjoy my "little" engines a lot an finally, they behave mostly the same to the real thing, but in a "trunk-sized" version. I love & enjoy your content sad to get you lost in the RRO team, but knowing you more involved as the CRRM, I have to book another flight over to the states some day soon.
@Hyce7772 жыл бұрын
cheers mate :)
@Ratkill10 ай бұрын
Its always a little bit bittersweet when I find really good videos about things I'll never get to do 😭
@nameridstormfellow55782 жыл бұрын
Thank you very much for posting this! I am right now learning how to fire UP #119 and this video definitely helps for how to do it! lately have been making the safety valves go off more than I would care to, so these tips might allow me to "control" 119 better!
@Hyce7772 жыл бұрын
Always a fun balance! You'll dial it in. Safeties blowing is better than the opposite - it all just takes time. Best of luck mate!
@andyconnrock2 жыл бұрын
Dude! Not only are you a steam fan. But you are a guitarist who prefers Marshall Amps! My man! I feel like we'd be bro's after like ten minutes of hanging out!
@Hyce7772 жыл бұрын
I do love me Marshalls :) come join the discord and chat!
@beesbeesbees-andbees10 ай бұрын
I would love a full video of you and your crew members working on a locomotive
@forsakenghost70542 жыл бұрын
WOOOHOOOOOOOO another hyce video and its one i am really looking forward to it as ive always wondered how fireing a steam locomotive is done
@sushifox3931 Жыл бұрын
19:18: Bro, Hyce is havin' a good time. 😂
@theSquashSH2 жыл бұрын
You're very good at explaining things! Thoroughly enjoyed this.
@Hyce7772 жыл бұрын
Cheers Nick :)
@TheOneTrueDragonKing2 жыл бұрын
Your comment about firing a steam locomotive being a "hot job" can be taken SO many different ways. Yes, it's literally hot, dusty, exhausting work. But for a railfan it's gotta be "hot" as in exciting. Everyone wants to run a steam locomotive, and while not as "hot" in this sense as the engineer's position, one would think railfans would be clamoring to be in the cab in any position. I know I'd love it. Steam locomotives are my passion so "hot, dusty, and exhausting" is actually fun. But the other kind of "hot" is also true for me. Also, that scene of you flipping your hair makes you look like a rock star in concert. And in this case, you are - or more accurately, you're a "coal star"! EDIT: Pardon me for asking but Is No. 20 a Camelback? That's the only place I've seen a firebox which extends between the engineer and fireman like that.
@Hyce7772 жыл бұрын
Nope! 20 is a deckless engine, which means there's no deck behind the boiler inside the cab - so the engineer sits on the side. A camelback has the cab even further forward, haha.
@TheOneTrueDragonKing2 жыл бұрын
@@Hyce777 Ah, I see. I've never seen a deckless engine before, so that's why I was confused.
@jimschneider51932 жыл бұрын
Incredibly informative. Love steam locomotives and these videos are awesome.
@chasesrailwaylinesrr64472 жыл бұрын
Nice model train set in the background
@GeorgeZ213 Жыл бұрын
20:05 that is an incredible amount of pressure! Looks like steam shot a good 20+ feet.
@Tank2452 жыл бұрын
19:19 On our steam locomotives we use fire hoses to fill up the tenders from a hydrant near the depot. There's a small hole in the hose and on hot days i'll angle the water spraying out of the hose leak up into the air so I can also cool myself down with the water haha
@Hyce7772 жыл бұрын
That's the vibe right there, hahaha
@SignalLightProductions2 жыл бұрын
Great video as always Hyce! Kudos to you for not shooting your engineer a dirty look for slipping like I usually do haha.
@Hyce7772 жыл бұрын
If it was one of the usual guys who's really familiar they would've gotten a very dirty look. In this case, a good friend of mine who's run a lot of diesel and was just now breaking into steam, so it was a teaching moment.
@SignalLightProductions2 жыл бұрын
@@Hyce777 haha that's fair.
@Cemtex992 жыл бұрын
So i just started watching you and thought what is this kind of nerdery with train. but i have to admit. You make the whole thing about trains so much more interesting than what i could imagine it was. Now i cant stop watching your vids. Keep it upp man Great work
@Hyce7772 жыл бұрын
Cheers mate! It's definitely nerdy for sure, but the best kind of nerdy.
@jeffreymcconnell67942 жыл бұрын
What an awesome video! Thanks so much for sharing all of your knowledge in a fun way. Stay safe!
@tylerodonnell-paccione75232 жыл бұрын
Hey we finally got CoverHyce in a video!
@NEAFarmKid40102 жыл бұрын
From what I've heard in a video with Neil Vodden (retired Southern Pacific engineer from the 40s and 50s), he explained it like this. I don't want to say the water glass is a luxury, its a very necessary thing. However, to know the true level of water in the boiler with an absolute level of certainty, you use the try cocks (or as he called them, gauge cocks). The water glass is a necessary thing, but if you are trying to check it in a hurry, you don't truly know if everything is functioning absolutely correctly.
@Hyce7772 жыл бұрын
That's pretty accurate - I agree, I'd hate to not have the water glasses and they're the go-to.
@raymondszybowicz7597 Жыл бұрын
Wow there really is an art to fireing every facinating.
@johnpenner39572 жыл бұрын
First and foremost, your Steam 101 videos are an excellent series, and I enjoy them immensely. Two thoughts on this one: (1) I agree with @Frank DeStefano regarding the use of gauge glass vs. try-cocks. When stationary, the try-cock is potentially the more accurate measurement but they're also subject to issues, including plugging from scale, etc. When moving the gauge glass should always be the primary indicator. (2) At 2:14 you state that, "If you have too little water, the steam locomotive can explode..." This isn't the case. If the water level gets too low, the fusible plug should let go, and your water will dump into the firebox in a manner which can only be described as "spectacular" and requiring a fresh set of drawers for the engine crew. Most boiler explosions are actually a result of losing the water, often combined with a failure of the fusible plug, and the crown-sheets/rear tube sheet superheating. Who ever is working the water notices that they've lost the water and opens up the injector and a flood of [relatively] cold water hits the super-heated steel, flashes over and *Boom*... Low water can result in some really impressive steam leaks, but rarely, unless combined with other factors, an actual explosion..
@Hyce7772 жыл бұрын
Many locomotives, including all of the ones I've ever fired (7? if memory serves) - do not have fusible plugs. Yes, for locos that -do- have the fusible plug, your description is correct. I'd be interested to see how many locomotives do/don't have them, because I imagine more do than don't but that's not been my experience. Cheers mate.
@johnpenner39572 жыл бұрын
@@Hyce777 Interesting - I had always thought it was an National Code requirement. Thanks again for the great content.
@snowboardhikebikeutah Жыл бұрын
Thanks for making these instructional videos. I always learn so much!
@zozol3562 жыл бұрын
I thing videos with fire are the coolest ones. I would love to see no cut firying up livestream or something. I would be awsome
@Hyce7772 жыл бұрын
Might have to do that when I get to the museum :)
@raymondszybowicz7597 Жыл бұрын
You are a very knowledgeable young man enjoyed your video.
@godlugner53272 жыл бұрын
28:06 "not my wife's idea of casual dinner talk"
@markstafford55862 жыл бұрын
Hyde. Once again thanks heaps for you work. Very enjoyable
@GGM_Grievous00302 жыл бұрын
Great vid! Near the end at like 47:45 that, but like traveling from the museum to a town and back, not just doing the circle run and talking over the vid to explain a few things. That is what I meant. But still learned quiet a bit.
@OfficialUSKRprogram2 жыл бұрын
What a great video! Thank you!
@MK.51982 жыл бұрын
hearing and even seeing how much depth there is in these things, it makes me a little sad that only NOW does the average person have the ability to really freely record their thoughts and share them with others. how much more advanced, or at least easier to teach, would stuff like this have been if we had the ability to communicate so easily then as we do now.
@MK.51982 жыл бұрын
its a small miracle that we even have what we have from then. It's a big part of what makes preservation so important to me. There's a lot of the human experience encoded in these ol iron horses. The only way for us to access that information is to go and DO the things that people of 100 years ago were doing.
@michaelh.9866 Жыл бұрын
Thanks, Hyce!
@wwrr982 жыл бұрын
38:04, I know exactly what you mean! It's easy to heave it up to the front corners, but about a foot or two back, I have the same issue. I volunteer at the Wilmington & Western in Delaware, and our 0-6-0, which has a 3 foot by 10 foot flat grate area, likes to eat up coal just behind the front right corner. Plus we only run steam about 30 days per year, so it's difficult to stay seasoned.
@Hyce7772 жыл бұрын
Very cool! Yeah, those medium long throws can really be tough. Always fun where they decide they like to burn the hottest. Lol
@HoboHoboLOLFUNNY10 ай бұрын
You know I really wish that there was a game of some sort that really simulated the Nuances and principles of hand firing an engine shown in this video...… Maybe someone will look into that some day.
@michaell.maloney4026 Жыл бұрын
Would be great to see a shut down series. Learned a lot. Thanks
@geoffreywilliams93246 ай бұрын
Thanks. Managing the boiler is clearly very important on a steam engine . .
@jordonfreeman1662 жыл бұрын
When Norfolk & Western 611 took on Saluda Grade, she had to be fitted with a special extra-long Saluda sight glass due to the steepness of the grade.
@darkkennight2 жыл бұрын
I'm learning a lot keep the fire men videos coming hopefully I will be firing steam engines soon my self.
@rocker414411 ай бұрын
For your blowdow valve. The pressure difference and temperature is what makes the water flash
@neiloflongbeck57052 жыл бұрын
For further information see the book "Handbook for Railway Steam Locomotive Enginemen" or the LMS training film "Little and Often".
@Hyce7772 жыл бұрын
"Little and Often" is excellent. A fair amount of British-specific things in there, of course, but a great film.
@robertbalazslorincz82182 жыл бұрын
20:27 "we do a slight amount of trolling"
@stephensfarms71652 жыл бұрын
Thanks for the fire lesson on coal, I learned allot about coal from video, hope to visit the museum soon, never been. Great video enjoyed watching 👍👍👍👍👍😂🎉