First Timer Maintenance on my Royal Enfield Meteor 350 ! 💙

[@johnbarrett9144]

Great job and an enjoyable, pretentious-free, presentation. Your Dad would indeed be proud

[@restdayrider]

Thank you. 😊

[@kevindarkstar]

Hi, if you don't mind me giving you a few points, first thing when you are spraying the chair cleaner on use a piece of cardboard behind the chain and in front of the wheel and tyre, as you really don't want to be spraying your tyre, also as to when do you know when you have been around the chain, always start from the split link and when it comes back around you'll have done the whole thing, once you have done that, use the brush on the bottom of the chain having sprayed the brush with the chain cleaner, put it on the bottom of the chain push up with the brush and turn the rear wheel, then wipe your chain down with a lint free cloth, once it's dry, leave it for 5 minutes to dry by the way, the re lube it. And well done for get ya hands dirty and doing it 👍🏻

[@restdayrider]

Thanks for the tips, everyday is a learning day!

[@UPTHETOWN]

@@restdayrider And for bikes that don't have a split link? Paint one of the links with a marker pen

[@volt8684]

As a motorcyclist of 46 yrs. my most hated job is chain cleaning, I have tried so many methods. However the one I use which I feel is not messy and very little time consuming is this. Its also very inexpensive as most cleaners and lubes are a rip off. Try this it wont cost much. Buy some paraffin off u tube or diy store. Tip some in a bowl. Wear gloves, soak a rag and rub chain to get worst off you will be amazed. Also cover your tyres with something. Paraffin does not attack the o rings in the chain either. Then get a brush and work the paraffin in the crap will dissolve. Put some cardboard under for drips. Wipe with clean rag and let dry then wash off and dry and lube.It will be like new. I keep my paraffin soaked rag in an old lunch box and it stays moist and can resume anytime. Its the fastest and least messy method and imo gets the crud off incredibly easily. Watch Fort Nines vlog on here about chain lubes. Very scientific but msg is don’t waste ur money. The beauty of paint brush method is you can do belly pan front and rear cogs too at the same time. Just keep off the tyres at all cost but if you get some on wire wool it off. Looks like ur chain needed adjusting, you have already started your maintenance journey and the chain is easy and more times you do it the more confidence you will get. Always check the oil on RE bikes. Love the colour of your meteor

[@BlueRidgeRider]

Excellent video! You performed more maintenance than most people are capable of! The thing to look for with sprocket teeth is are they symmetrical? If they start to look like little shark or dolphin 🐬 fins, it’s time for a new one. While you’re down there you want to check the tension of the chain. Since cameras tend to distort the image I won’t say your chain is loose but it kind of looked like it in the video. The procedure is spelled out in a Royal Enfield video but it’s basically, measure the sag, loosen the axle nut tighten the Allen bolts on the adjusters until the chain is correct, then tighten the axle nut. I always give the adjuster bolts an extra tweak once the axle nut is tight. If your axle was properly aligned before you started, it is safe to turn both adjusters the same amount. Not more than 1/2 turn at a time. The proper way to clean a spark plug is using a special sand blaster that’s made for the job. Most people just replace them before they get around to cleaning them. What you are inspecting is the ceramic insulation (cone) around the center electrode. Black or oily is a bad sign. Less common but also a problem is white deposits. Yours was a perfect light tan. Use that as the example for future reference. Congratulations on a job well done!

[@restdayrider]

Thank you very much for the positive feedback and helpful comments! Everyday is a learning day and tips from those experienced is always very welcome!

[@davidskogley3570]

Well done! Best way to learn about a bike. Upwards and onwards!

[@benttrout1962]

Very brave of you to show your learning here. I went through the same learning process [as we all do] albeit 50 years ago. I'm sure others will have given you useful tips. Your videos are thoroughly enjoyable, keep 'em coming. regards John

[@restdayrider]

Thank you John. 😊

[@user-ot1dv6ri4f]

I second this and really enjoyed this video

[@drost582]

You are very comfortable in front of camera, a natural. This channel should go as far as you want it to. Great job on the maintenance of your bike. Have you seen BikerStuff channel? She has lots of good content on bike repair and maintenance, but attracts lots of male viewers. Keep up the good work and great bike content. Thank you Charlie.

[@restdayrider]

Thank you Ken. 😊

[@paulstoker7650]

You should be really proud of yourself, you did a good job. There's lots to do on a service but that's all part of the experience, with your, I can do this attitude, you'll master everything in no time. Take care and ride safe.

[@restdayrider]

Thank you Paul. 😊

[@markchase7419]

very clean air filter!!! of course when one lives near dust, sand, etc..air filters get a lot more clogged. good video!! 😎

[@petehealy9819]

Very nicely done! I'm glad your video popped up in my feed (I bought a Fireball Yellow Meteor recently as I downsize after 50 years of riding), and I'm also glad to see numerous good tips among the comments. All the Best from Kentucky USA!

[@sligoquadcopter]

Well done. Personally I would not allow the degreasing and lubricant spray anywhere my tyres or wheels. I always make use of a large piece of cardboard behind the chain to act as a spray and splash guard. On my Meteor 350 I also make a point of checking, and adjusting as necessary, the chain tension when I clean and lubricate it.

[@lauriecremore5601]

Love your talk throughout this

[@Drake621]

That was very enjoyable watching , I also have a 350 Royal Enfield , going to do the same maintenance tomorrow Awesome

[@restdayrider]

Thank you 😊

[@mandymorris3341]

The word "Stuff" is a brilliant word for describing a million things. Well done on the maintenance.

[@restdayrider]

Thank you!

[@peoplespowerhellyeah8619]

Your videos on meteor really helpful to those who are facing these problems....give us that kind informative videos..

[@restdayrider]

Thank you. 😊

[@shaunhagan393]

As professional as anyone can be, congratulations on starting your journey into mechanics! May I suggest a dab of tipex on the chain to illustrate the starting point?

[@restdayrider]

Thank you 😊

[@BavarianBlackBear]

I am about to do my first check up on my new bike. I love how you said there were no extra bits :)

[@robgerety]

Great job. Next - change oil and filter, and maybe even try to check and if needed adjust valve clearances.

[@speedfinder1]

Well done, little by little, it's a great thing to be able to do basic maintenance for yourself. Where Royal Enfield have really stolen a march on other manufacturers, is their ease of general maintenance. A little confidence in your own abilities will definitely reduce the risk of being stuck at the side of the road in the future. 😊

[@restdayrider]

Thank you, I'm learning slowly! 😊

[@annettesomers7463]

Good job. I do everything on my kymco like. Spark plug , air filter, motor oil, gear oil, fuel filter. Now I have a new meteor under warranty, so get the mechanic to do it all. But when the warranty runs out, I'll do everything myself. Good on you 😊

[@restdayrider]

Thank you 😊

[@willyrackham2957]

I'm loving all your vlogs .....you will get loads of good advice from all the bikers on here ...one tip if you get in any problems and you are in a bit of bother ...always ask a gnarly old biker they will always help

[@restdayrider]

I absolutely will, and I've found the ones I've approached so far have been nothing but wonderful. 😊

[@leslatham7797]

You missed the most important part of the job, your tea was far too milky! Love your videos Charlie. Just taken delivery of my new Scram. Keep it shiny side up, and keep the videos coming.

[@restdayrider]

You'll love the Scram 😊

[@johngiorgini6813]

another great video Keep it up MLR

[@the.just.able.biker67]

As has been previously said, it's the inside of the air filter that needs checked. You'll notice the plastic cap with the 3 screws has a bell shaped hole that sucks the air in. It then passed through the filter and into the engine. It'll look the same on most bikes these days, slightly different shapes, but they all have a cover with bell mouthed sooker. 👍 The next 2 most important things are, 1: check the oil level is correct. You're owners manual will show you how. 2: Adjust the chain. Again it'll be in the owners manual, and there's plenty videos on KZbin showing you how to do it. If a chain gets too slack it can bounce off the sprocket and get jammed in the wheel. Other than that, kudos for getting your hands and "What the fuck is that" face dirty. 🤣🤣

[@robertmarshall2521]

Hi just come across you KZbin videos loving them. So good to see you going through things you’ve never done before and explain why you have undertaken them. Bike looks good and your willingness to get your hands dirty by undertaking routine maintenance is credit to you a real biker not a pavement princess who only rides when the weather is perfect, no rain road recently cleaned and a bike that spends most of its time I’m a air conditioned garage and only ever sees a dealer for routine maintenance. Just a quick Q I noticed in this video your towel are you a veteran ? Me too as I guess a lot of your follows maybe

[@restdayrider]

Hi Robert, I have never been one to shy away from getting stuck in, and every day is definitely a learning day. I'm not a vet myself, but have family members that are. 😊

[@robertmarshall2521]

@@restdayrider thanks for the reply I was just curious. Looking forward to your new adventures keep the rubber side down

[@winksmt01]

That's it, workshop manual next. Valve clearance, fork seals and wheel bearings etc etc. Enjoy your maintenance and ride safe. 🏍️🏍️🏍️

[@alangordon3314]

Well done Miss, down to earth pragmatic presentation.

[@lorenzodawes8778]

Great job on maintenance. When I got my Honda Shadow, warranty was one time, afterwards I could do it myself or taking in to the shop. But still have the warranty. At the time the maintenance was around $300, I believe. It's good to learn about your own bike. Makes you a better ride, safe ride, and have more fun. Ride safe.

[@restdayrider]

Thanks Lorenzo. 😊

[@lorenzodawes8778]

Your welcome🤗. It's now about 130 am in Az. Can't sleep.

[@skippercaship]

Well done great job x

[@nunnyd69]

I learned from experience that if you ride off-road or do alot of road mileage in all weathers you’ll inevitably pick up bits of dirt and grit in your spark plug well. If you can, blow the grit and dirt out with an airline or compressed air can or even a drinks straw before taking out the spark plug to prevent any harmful cr@p from falling into the cylinder when you take out the plug. If you can get a spark plug well infil or gator get one as it’ll stop a lot of the large bits getting in and also rain/road water which can cause a short across the lead to the head and cause your engine to cut out.

[@pauldixon3089]

Hi Charlie, I think you did well looking after your bike. It's all a learning curve and the more you learn your confidence will grow too. Could be a worthwhile investment seeing if you can do a maintenance course at your local college or even better, ask your local,friendly bike shop if they will teach you some pointers. Free labour and cakes sound like a fair trade to me.☺️ Happy biking😃 Ps, you've made me hanker after an Enfield too now😂

[@tonyminter3823]

Well done. Always a good feeling to learn new things about your bike and to take the trouble to look after it with basic maintenance and ride pre checks is both a safe and smart habit to get into. I enjoy all your videos, thanks for sharing. 😊

[@restdayrider]

Thank you Tony, I had fun learning, and as you can see was a little bit chuffed! Good to know you enjoy my vlogs! 😀

[@tonyminter3823]

@@restdayrider Yeah you deserve to feel chuffed, too many people just wait for a service to discover issues. I love the practical simplicity of my own new Meteor (fireball yellow) Its a fantastic fun bike. I like the fact you have one too and your vlogging about your Meteor in the UK. So many are from the US or India. I also work for the NHS so a fellow health care worker has my 👍 😊

[@matthewholmes7597]

@@restdayrider Hi nice motorbike i wouldnt mind riding with you

[@user-ps6qi9fi4o]

Great job, If removing components for servicing /cleaning then do take pictures of how it looked prior to disassembly. Then you have a reference to how it was beforehand.

[@andrewweitzman4006]

Ah, shade tree mechanic maintenance. I was a completely unhandy middle class guy in his late 20's who had never anything automotive beyond helping with washing my dad's car. Doing my first successful maintenance task was awesome. Really screwing up my second less so, but a learning experience. I admit that these days I just give it to the mechanics. My BV 350 is much less maintenance friendly than a Royal Enfield. Even replacing the headlamp bulb is nine assholes to do.

[@Hugh-S]

"we're gonna put it back together and see if I've totally sodded this up. let's hope not eh?" - Things you DON'T want to hear your Paramedic saying lmao. Well done on the bike! it's a Beauty, love the colour.

[@restdayrider]

Hahahaha, I'm definitely more at home putting people back together!

[@Hugh-S]

​@@restdayrider Well with your attitude you display in your videos and your personality, whoever you're working on is very lucky indeed. Thank you so much for doing what you do!

[@LVSHELP]

Refreshing video nice

[@bidouchonsan]

good job done. i don't know if you have noticed, but at 8:20 and later we can see drops of water leaking by the plug wire. and as it was said by others, don't do like me and be carefull to protect your rear tyre before lubing your chain. You may have check the gap of your plug with gage, the right gap must be mentioned on the user guide or workbook. You can also use graphite grease on your plug and it must be tightened as a recommendend torque, no need to overtightnen it.

[@BarryFrancis-id1tn]

Paraffin for chain cleaning, far cheaper, than cans works great and wont harm the chains O rings.

[@Fubar_The_WEF]

I watched this video because I'm about to take delivery of my Meteor. Very informative. Thanks. There is something I do when taking out the spark plug is to put a spot of grease or oil on the threads before putting it back. It makes it easier to get out next time. Also I would invest in a spark plug brush for cleaning it. It's a little wire brush. It'll do a better job than a cloth. The gap will get wider with use so you do need to check the gap.

[@restdayrider]

Noted, thank you, I believe there's a crush washer that I should have used putting it back in also? I suspect I also need a feeler gauge. Excellent choice on the Meteor. 😊

[@restdayrider]

Make sure you subscribe for more Meteor bits and tricks from me.😊

[@Fubar_The_WEF]

@@restdayrider I can't wait for it to arrive! I had a test ride on the Himalayan but I couldn't get on with the foot peg position. They are set too far back for me, so my knees are bent more than on other bikes and I've had knee problems for years. The crush washer is very difficult to take off! So you almost certainly put it back anyway. Yes to the feeler gauges.

[@beakittelscherz5419]

"How do you know when you are fully around"? Tea starts to taste like #Bike 🍵😂😂😂

[@restdayrider]

I've just fitted a new DNA filter cover, and actually dropped a screw in my tea cup. 😭

[@rodfryatt4266]

Well done; but you did get it the wrong way round! .......... Always remember the words of the late lamented John Ebbrell "Spanner work first, then shine if there's time."

[@chrisrobinson860]

Brilliant video. Best way to learn. Go for it girl.👍

[@restdayrider]

Thank you Chris! Every day's a learning day. 😊

[@elwood62]

They actually gave you a spark plug wrench that fits the plug. Sadly mine doesn’t. Allen wrench is the wrong size for the panel over the air filter too, which I found out late one night by the side of the road trying to diagnose why the engine was running poorly. But I digress. Good job on the maintenance.

[@michaelfirth1075]

Well done young lady.😊

[@restdayrider]

Thank you 😊

[@TheArtdecovampire]

Great vid. People expected their Mutt to keep going with no TLC. This is it, every biker should know their basics. You do it with style.

[@restdayrider]

Not sure about the style, but maybe that'll come with practice! 😊

[@duanetrivett750]

I think you are doing great on your up keep ! I will be watching for more videos . just wanted to say Hello from the U.S.

[@restdayrider]

Thank you! And hello back from across the Pond. 😊

[@CornishMotorcycleDiaries]

Good solid basic maintenance there. II'm sure if we checked the spark plug every time the chain was lubed, there would be fewer breakdowns. At the risk of sounding like a knowledgeable bloke (I'm really not, if I was a superhero, I'd be Captain Clumsy...) It's a good idea to put something like a decorating sheet under the bike to catch all the crud that comes off. Helps to keep the SO happy. Also, greetings from Cornwall and a fellow NHS worker. 🤟😊

[@restdayrider]

Hi! I'm taking all these tips on board for next time! Thankyou!

[@ramsien]

Something that doesn't get talked about nearly enough are (Japanese Industrial Standard) JIS Screwdrivers. Tradition Phillips bits were designed to pop off the screw before they were over-tightened, this was at a time of factory/mass-production use and the screws were not intended to be removed; but as it became standard in general use we're now largely stuck with a driver bit that has a tenancy to strip screw heads. Enter the JIS, these bit drivers are shorter and less tapered and so seat better inside the screw head and don't pop out and so don't strip the head. So if you have a JIS or Phillips screws on your bike a JIS Screwdriver is the way to go.

[@restdayrider]

That's interesting to know, thank you! 😊

[@maskedavenger2578]

The bike is produced in India ,it is highly unlikely to use JIS fasteners ,they are more likely to be slotted or standard Phillips .

[@Rudibeata]

Well done Lady👍👍, but the screwdriver for the air filter must be one size bigger. The small one can destroy the screws. regards from the north of Germany.

[@restdayrider]

Thank you. 😊

[@geoffluck]

Nice little video, half the benefit of doing these little jobs is that if anything else is awry in the area you are working on it will be discovered. My meteor is red, and still running in, but the dealer assured me red ones go 10mph faster😉

[@restdayrider]

I'm not sure I'd recognise awry yet even if it had a label on saying 'Something here is Awry!' Blue Meteors are proven faster and more economical, plus the go faster stripe I added increases BHP by at least 20. 😏

[@geoffluck]

@@restdayrider I imagine with two go faster stripes my red one might be competition...😁

[@UPTHETOWN]

@@geoffluck Red bikes are always faster, well known fact

[@gerrypowell2748]

Good work,if you have loads of dough,I would consider a Scotoiler,makes the chain lasts longer and back wheel stays a lot cleaner👌

[@restdayrider]

Thanks Gerry, I'll have a look. 😊

[@d.4tay549]

Good on ya mate!

[@dennisbuckley]

I love that you used the RE tool roll and not several hundred pounds worth of top-end socket set, torque wrench, etc. I’m assuming your logic was ‘these are the tools provided so why use anything else’ which seems fair enough 👍 V commendable! That little tool roll can probably get you out of a lot of fixes roadside. This is why I soon hope to downsize my smoke-and-mirrors techno-bike for a 350 Classic…

[@restdayrider]

Use what is provided for the job until proven otherwise I say! 😊

[@billcotton1551]

That was the cleanest air filter I have ever seen! You must live in a low dust area.

[@restdayrider]

I think it was as it was only 6 months old!

[@alaneverett2531]

🤣🤣🤣well done with ya thing and no bits leftover 👏 ha ha ha 😄

[@restdayrider]

Apparently that's always a good thing. 😏

[@G1920D]

Nice going keep up the good vibs you can do it all just do it xxx Gijs

[@julianchambers8372]

Hi, just a tip, I always put a spot of grease or engine oil on scews/bolts before refitting. I find this aids removal in the future. Better still use anti seize paste especially on hot fixings. Spark plugs tell a story of how your engine is running. Take a pic or youirs as it looks fine. Black is too rich fuel white too weak. Oh and always carry a spare.

[@restdayrider]

Thank you 😊

[@julianchambers8372]

@@restdayrider lf you ever need advice or a chat just call me.

[@waynepicton2425]

Well done on your first bit of maintenance, next is oil and oil filter. Like I always say is. you look after them and they will look after you.

[@rabh6746]

I wish the air filter on my NC700 was as simple to remove and refit, its a real pain in the ass🤣Great work for a first timer, it will get easier👍

[@restdayrider]

Thanks. 😊

[@pauld7827]

My Meteor is a 2021 model and I've decided, after the last bill that was more than a full service on the car, to do my own thing. It's only done 1900 miles! Also, I'm not convinced that the cables will be lubricated and the chain cleaned before greasing etc., by the dealer. Today, I fitted a DNA air filter and let that settle with running the bike on idle for 10-15 minutes. KZbin is great for this sort of thing! Tomorrow, I am hoping to fit a de-cat pipe, lower shocks and luggage rails. I say 'hoping' as what could possibly go wrong? The shocks are the big scary thing to undertake, especially as they are about an inch shorter than stock! From KZbin, I've just discovered that the early Meteors rely on part of the original exhaust to act as a bump stop for the centre stand! So that's the next scary job, to replace the centre stand with a modified one.... Another step towards confidence in looking after your ride. I have no experience in this type of thing but hey, watching the guys in India..... A penknife, screw driver, spanner and a bit of string is all you seem to need! It has become obvious, and as your air filter change with the RE toolkit demonstrated, that you need to invest in some good tools. I have bought a socket set, a set of spanners and some good quality screwdrivers and so far, the mods (screen etc) have been really straight forward. Great video, perhaps you will do more of your own servicing and post it so we can all benefit from doing our own servicing!

[@restdayrider]

Thanks Paul, hope the de-cat went well!!!

[@pauld7827]

@@restdayrider thank you! Well, the shocks went really well with me using a length of pipe to raise the rear wheel…… the only problem I have is some blowing between the down pipe and the de-cat pipe - I think I know why. So taking it off to refit. Feeling rather chuffed to be honest! We can do this stuff! Just look it all up and take your time.

[@restdayrider]

That's brilliant!

[@NanoByteGhost]

Spark Plugs just need the right feeler gage placed in the gap, then gently tapped until it squeezes the qage.... Job done. Tappets are similar but you need to make sure your pistol is just short of top direct center, then set the gap on those too. On a single cylinder its easy. You do that by putting a screw driver down the spark plug hole and slowly kick the engine over until the piston is nearly at the top and about to start going down. Then set the tappets and timing as needed. Dont forget to change the oil :)

[@guyonacub4335]

You can also make a note in your service book that you have checked your bike date, and what you have done check with your dealer for confirmation. And if you start to fully service your bike yourself then write it in the book and enfield will update there records But use oem parts and keep the parts invoice The invoice must show VAT when are you stripping the engine Enjoy 👍

[@restdayrider]

Good tip. 😊

[@geoffballe8766]

Good on you, you little thing 👍🏼

[@sagarmeena0210]

great work......love your the blue Meteor!!

[@NanoByteGhost]

You did well for the first time... Good work. :)

[@restdayrider]

Thank you!

[@gerrymac5865]

One of the best inventions on a motorcycle is the electric starter the days of priming the carb and kicking the engine over until you nearly have a heart attack is all gone,ride safe. 👍

[@restdayrider]

Still nice to see and hear it tho... When it works!

[@nploates]

“I’m a little bit chuffed!” - You should be, well done.

[@restdayrider]

Thank you!

[@anroadking]

You'll soon be checking and adjusting chain tension, Replacing the Oil and filter and adjusting the valve clearances. Brilliant!! 🏍👍

[@restdayrider]

Let's hope! Definitely getting more confident the more I do. 🙂

[@kevindarkstar]

Chain tension is a quite important one tbh and worth the effort, oh yeah and another little tip, with the chain adjustment when you check the free play, which is a bit over an inch of up Down travel, do it with the bikes weight on the chain, and if poss with you sat on it, granted this is a bit of a two person job, but if you adjust it on the main stand then take it off and sit on it I guarantee you that the chain will be tight as a nut

[@davidwaddington9414]

select one chain link, clean it with white spirt or something similar, dry it off, then paint a good dab of red/pink nail varnish on the outside of it, now you have a marker to let you know you have revolved the chain round once, it will stay on for years.

[@restdayrider]

Good tip! Thank you. 😊

[@bayoubuford]

good looking bike

[@jeynes14]

Well done girl.

[@restdayrider]

Thanks Ron. 😊

[@DonBrady-p7h]

Thank you, I enjoyed this very much. I have a Meteor as well and I want to know how the heck did you get it up on the center stand? I can't get mine up. I've tried, I've had an experienced biker try, very frustrating. Any tips would be appreciated.

[@restdayrider]

That's odd, it is a little heavy but a good sturdy boot push down and she's up!

[@nigeltankard6977]

Charlie, nothing seems to phase you 🙂

[@restdayrider]

Spiders and heights. 😆

[@nigeltankard6977]

@@restdayrider i am not good with heights either

[@paulfoster5432]

The thing about the air filter, It's only really going to be dirty on the inside, unfortunately where you never looked? But on the whole I'd say well done 👍 Cheers Paul Foster

[@restdayrider]

I know this now. 🤣

[@paulfoster5432]

Sorry 😔 I guess a number of folks said that 👍 All the best Cheers Paul

[@robertwalmsley755]

Loving your posts great effort😂

[@restdayrider]

Thanks! 😊

[@RiderOftheNorth1968]

Hi! Several commenters have touched on cleaning and lubing the chain so i will leave that. But.... Get a can of breakcleaner just in case you need it next time. Remember to NEVER EVER fall for the temptation to rotate the rear wheel, while cleaning, by having it running in first gear on the centerstand. That is a proven way to loose fingers, for real! Note on the air filter: It is the inside that´s gets dirty i believe.... Good luck next time! An independant biker is a happy biker, drive safe.

[@restdayrider]

Thank you, I take all tips and hints on board!

[@iangrimshaw1]

With respect, if the inside of an air filter is dirty and the outside clean I'd guess you have a major problem. Possibly a worn inlet valve blowing back. An air filter will be dusty/dirty on the outside 'cause it's there to keep the dirt out. As part of your tools I'd suggest getting a magnetic screw/bolt/washer dish to pop the screws in. If you drop three screws on the floor one of them WILL end up in the next county, down a drain, somewhere inside the frame etc. Keep learning and take care.

[@iangrimshaw1]

Ahhhh! I've had another look and I get what you mean. The air intake on the filter cover goes to the INSIDE of the air filter. Sorry if I caused any confusion.

[@stevetaylor8698]

Your chain was cleaner before you cleaned it, than mine is after I've cleaned it.

[@nickmason279]

Well done you, you're an inspiration and I hope people follow your example.. Most people either just don't bother or pay someone to do it. I love my my Meteor and have always done my own spattering. One thing I've learned in over 40 years of bike ownership is that chain lube in cans is fine but expensive snake oil. I keep a small amount of old engine oil, new is fine. Clean the chain then apply the oil and use a rag wipe off the excess. There are lots of videos about this verses the more expensive stuff and it's all personal choice. Also don't struggle with the wrong tools, sometimes you need the right tool for the job. They're aren't expensive and no need to buy a set full of stuff you probably won't use. Just buy the one you need, it can make life so much easier.

[@restdayrider]

Thank you for your tips and advice. 😊

[@triumphrider572]

Hi, Excellent video. Well done! Here's a tip from someone who's broken spark plugs in the past. Try and find some foam or rubber pipe to fit into the plug spanner. It'll stop you cracking the porcelain.

[@restdayrider]

Thank you! I'll take all tips on board. 😊

[@peterwait641]

A light smear of copper grease on the spark plug threads helps stop them seizing in .

[@triumphrider572]

@@peterwait641 Yep always done that too. I'll never forget the time I was out on a T140 chop I had and it suddenly went onto one. Luckily the plug cap still had the plug in when I stopped. It had stripped the thread.

[@regk9077]

haha.. ya done good!

[@heywhotsgoinon8286]

If you can, or want to, get a torque wrench and workshop manual , if youre going to keep the bike. Just so you dont overtighten any bolts. Especially if you have a go at changing the oil.

[@danielmcneil3004]

Very good work. 👍👍

[@restdayrider]

Thank you!

[@vaibhavwani1509]

Hi, What's that long yellow lock you used in the end (at 11:01). I would like to have one of those if you recommend. Can you link me to it? Btw, love the part where you patiently read the instructions either on the cleaner, or the tyre pucture kit, or the throttle lock. Keep sharing these pure experiences!

[@restdayrider]

The lock is just a disc lock on the back wheel, with an elastic stretch to the bars to make sure you don't ride off with it attached. 😊

[@2ndcornets]

@@restdayrider If you don't have a "reminder" cable you don't half look a twit when you ride about three feet and then tumble gracefully off as the bike wheel locks up and it topples over lol.

[@nigelcopestake3618]

Good to see a lady get stuck in, if you don't try you will never learn. Although just one thing, you should have taken the outer end cover of the air filter element and checked the inside, that is where all the crud is court. Yes you should have checked the spark plug gap with feeler gauges and checked the colour should be light coffee colour. Good job, keep up the good work

[@screemerek1]

I can not agree … Let’s be clear … it’s not 1975 anymore . Meteor has an electronic computerised fuel injection system, so there is totally no point to touch the spark plug at all, especially at 1700m on the clock. First , the “coffee colour” tip makes no sense as the bike is not carburated, and there is no way to adjust the idle fuel mixture on this bike (the incorrect colour shows that this adjustment is needed if your bike uses carburettor ) as the ECU of the bike does it automatically using oxygen lambda sensor readings . also mind that on modern spark plugs that have iridium or platinum electrodes you never use any feeler gauges and you never gap them as they are gaped when manufactured … touching the electrode with steel feeler gauge breaks the iridium or platinum layer and the spark plug the. can only be used as a Christmas tree ornament. Also it’s 21 century and when your spark plug is broken (yes they just break sometimes) you go to Halfords and buy a new one for about 15 pounds.

[@UPTHETOWN]

@@screemerek1 So how do you know if somethings wrong with the EFI/ECU/oxygen sensors etc. if you never touch the spark plug? Indeed, how do you know when new spark plugs are required. Just because something's new doesn't mean it's perfect. It may not be 1975 but the ability to read a spark plug is still important in 2022

[@screemerek1]

@@UPTHETOWN I did not say it’s not important, it’s important when you have a malfunction, but checking the colour of electrode will not give you anything on efi as even if you have condition that makes your afr incorrect ecu will compensate it by adjusting injection and ignition timing. Then it will light up your MIL on the dash and this is your indicator of the malfunction. Then you need some kind of can/obd reader to check your error codes and live parameters. Yes you’re right to check if you need a new spark plug you have to take it out.

[@NanoByteGhost]

Regarding Chains, i found a little 3 in 1 oil was good enough. Sprocket teeth start to appear bent, as in like a wave when they start to wear out. At that point just replace the sprocket. If the chain becomes to slack and adjusting it appears to do nothing, replace the chain.

[@restdayrider]

I love the 'just replace the sprocket' 😊

[@irealworkshop]

very good. It would be better not to spray the chain cleaner and lube on the wheels and tires.👍🏼👍🏼👍🏼

[@restdayrider]

Noted! Thanks.

[@eclipselabels]

I’ll bring mine round next week 👍🏻

[@restdayrider]

Yours has a few more plugs than mine! 😂

[@mrnobodytheuser2950]

Such a cool looking bike.

[@restdayrider]

Thank you. I like it!

[@betacam235]

What happened to the small smoked flyscreen? Or does this video pre-date it's fitting?

[@restdayrider]

Hi, yes this one is before I fitted the screen, it's been brilliant on my current tour. 😊

[@andrewrobinson3030]

Well done. Next time will be easy

[@paulhenderson9585]

Looking at your air filter intake the dirt will be on the inside of the filter not the outside.

[@restdayrider]

Hi - ive realised this since from the tips people have given. :0)

[@dariuszrubas5739]

Hello. I was seen your movies. What you thing, whats a better for small trip 300-400km your Meteor or Himalayan? Good luck !

[@restdayrider]

Either to be fair, but the Himalayan is a little more comfy for me due to the sitting up position.

[@mikecartlidge5355]

Well done, the more you learn about your own bike and especially about servicing then the cheaper running costs are for you. If you get the chance have a look at adult education classes in your area, you maybe lucky and find a motorcycle maintenance class which can be a big help. As far as tools go the right ones make the job easier, the factory fitted air filter cover screws would have come out more easily with a tee handled philips screw driver, less effort needed and more purchase on the screw head, also a basic set of metric combination spanners, 8mm to 19mm, ring spanner one end, open ended spanner at the other....eBay is a good place to look. Nothing like rolling your sleeves up and getting your hands mucky.

[@restdayrider]

I am definitely keen on a course, maybe I'll treat myself. 😊

[@iangrimshaw1]

@@restdayrider You really should. I self-taught my self when I was 16 and over the next few years caused more damage to my bikes than you would believe possible. Get on that course.

[@racheltaylor6578]

You can get a UV torch from Muc Off.

[@Milo_Minderbinder]

Well, I think you did a little error in reasoning when evaluating the air-filter. The dirty side of an air-fimter is where the air comes in. You just checked the outer side. In this case the clean side, which is facing to the engine's intake. I know, most classic air-filters in cars operate the other way - but not in case of your Meteor.

[@restdayrider]

Yup, been told that one! Next time I'll know better. 😊

[@sourav6339]

🤔Be careful while tightening the spark plug almunium threads are delicate 😭,next time don't over tighten

[@restdayrider]

Noted!

[@squirrelcovers6340]

Excellent. Now check the oil level & tire pressure 😉

[@restdayrider]

Check it? I'll learn how to CHANGE IT! 😆

[@UPTHETOWN]

tyre

[@screemerek1]

It’s easy to check if you covered whole chain in meteor as one link (master link) has a bit different colour (I found that first time I was cleaning mine). Also good choice with brand of your cleaner and lube, I prefer the non dry one actually, as dry muck off leaves the ugly white residue. Also I found on the video you may have a frozen link on your chain … might be a manufacturing issue.

[@restdayrider]

Hi, thanks for your comments, how did you identify a frozen link, and how do I resolve that? Thanks!

[@screemerek1]

@@restdayrider it might be just my imagination or the angle of your video, but to check it ... just inspect all the links by hand - if all the links move freely when twisted/rotated then everything is ok, if any link stays in the position when you wiggle the chain then .... the chain should be replaced. Your total mileage is pretty low, so this should not happen (my bike has almost twice on the clock and no problems with chain, forzen links usually happen after 20k on the clock, but ...Im talking japanese bikes with DID chain.... Enfield may use some chaper brand that may be not same quality) As I said its hard to see it on the video - may be just camera angle.

[@restdayrider]

@@screemerek1 thank you for the heads up, I will take a more detailed look!

[@screemerek1]

@@restdayrider by the way - I see you have a lot of custom parts already (seat modifications, tail tidy, removed windshield, bar end mirrors).... is this a touring or lower seat ? How do you feel this one compared to stock ? Also soon Im going to make some video on mods on mine.... I have heated grips installed that I manufactured small special part (spacer) on the 3d printer to make fitting factory looking.

[@davelead2742]

Well done you you curse and cuss like a true professional Love and best wishes Dave

[@restdayrider]

I was taught by the best. 😏

[@davelead2742]

@@restdayrider Would that be the one you called after when the rear mud guard wasn't held up properly Dave

[@restdayrider]

😆

[@davelead2742]

@@restdayrider your a dark horse I'll keep an eye on you LOL

[@davelead2742]

All joking aside I've only just found your site and I find you to be down to earth and committed to the tasks that you set yourself and at 66yrs of age I'm a happy chappy watching you and I want my mrs to watch you and hope you inspire her to retry for her bike License ( she's younger than me so should be safer LOL) Dave

[@Adam-mo2qw]

Great content! What us the max speed and max cruising speed of your meteor?

[@restdayrider]

Motorways it keeps up with the traffic, but of a rumble through the pegs at 70mph. Cruising is it's sweet spot, and she loves 55-60 all day long.

[@2ndcornets]

@@restdayrider Same as mine. These bikes won't really do more than 70mph. they are limited to about that speed. Lots of mid range torque there for accelerating up to their 50-60 mph sweet spot though.