Installation of My New SuperFlex Rubrail

[@radjifmaduro3661]

Nice looks easy enough. Black nail polish for that set screw, I would go bunkers seeing that SS screw peaking out like that. Nobody will notice but I would know🤣

[@CaptOrlandoMuniz]

😂

[@silverbull2932]

Thank you for the video very helpful 👍

[@CaptOrlandoMuniz]

👍👍👍

[@TexasDeepSeaFishing]

was looking for your episode on how to rig for bottom fishing big fish.

[@CaptOrlandoMuniz]

Here is the link. Let me know if you have any other questions. Tight Lines, Capt. O kzbin.info/www/bejne/i6GXeainhZqipck

[@lesfaust9634]

Looks awesome 👌

[@CaptOrlandoMuniz]

Thanks! 👍

[@webe_fishing9345]

Came out awesome!

[@CaptOrlandoMuniz]

Thanks Bud! 👍

[@ShorrockPaul]

Nice install. , useful tips. Bit surprised no silicone on the new pan head screws ? is it not necessary ?

[@CaptOrlandoMuniz]

Thanks! It can be used but not absolutely necessary. 👋👋

[@johncarpenter1476]

Good video and tips, but I respectfully disagree regarding the silicon with screws. After time, those screws will develop small intrusions, develop enough cracks that its not IF, but when they start leaking into the interior. EVERY other video on this type of project includes cleaning the top/bottom boat joint new silicon on the joint AND silicon on the set screws to eliminate water intrusion... @@CaptOrlandoMuniz

[@capt.orlandomuniz-espanol2680]

@@johncarpenter1476 👍

[@keepnitreel2582]

Looks great, is it recommended to put 5200 or are the screws enough to hold in place

[@CaptOrlandoMuniz]

Thanks!

[@SteveIwaszkiw]

Should silicone be used on top and bottom of the trim?

[@CaptOrlandoMuniz]

Yessir!

[@scottlomas9165]

The cap on my boat in the bow appears to be coming loose from the hull after many years (1985), it looks like I'll have to remove the rub rail to reattach it, it appears also looking from inside the boat that rivets were used instead of screws. I noticed that my rub rail was sealed on both sides with silicone and in your video you didn't do that, any particular reason why you would or wouldn't do that?

[@CaptOrlandoMuniz]

Silicone can be used, especially if there is a gap between the hull and the rub rail. In my case there was little to no gap. Hope this helps! Tight Lines, Capt. O

[@jheiny1231]

Extra screws in the rub rail will hold the loose side of your hull down. And the seam between the cap and the hull you would want to caulk first before you install rub rail. You don't want to caulk on top and bottom of rub rail because if water gets in behind in needs a place to drain or you will have sitting water

[@BattleshipGrafSpee]

Beau travail messieurs ! :)

[@CaptOrlandoMuniz]

👍👍👍

[@patrickhampton6248]

How to get someone to fix my rail replacement

[@CaptOrlandoMuniz]

There’s a guy in Miami that specializes on rub rails. Believe it’s called Tommy’s Rub Rail. If not a lot of boat shops do it too.

[@abelvazquez6012]

That old rub-rail is 1-7/8 and that new Suproflex rub-rail is 2" inch, it comes out to flush at the top.

[@CaptOrlandoMuniz]

💯

[@cowboysnation1594]

Where do I buy this?

[@CaptOrlandoMuniz]

tacomarine.com/rub-rail-kits?gad_source=1

[@goose31171]

Hard to watch when the rub rails is getting stretched and dragged on hot cement. That’s a big non. Either do it over grass or lay down some blankets.

[@CaptOrlandoMuniz]

💯. We used blankets as much as possible. 👍

[@bipedalhominid6815]

That rub rail you pulled off was horribly placed on the boat. Looked like a rollercoaster. Good job replacing it.

[@CaptOrlandoMuniz]

Yes, It was badly damaged . Thanks, Capt. O 👍

[@jasonmurray8466]

It's like a human pacifier/face diaper

[@CaptOrlandoMuniz]

💯 😂😂

[@mikesanders902]

Mask????

[@CaptOrlandoMuniz]

I’m not a fan of masks but this was done during Covid and there was a good reason. 😌

[@ShadyOne9]

I cared up until I saw the masks…. 😂wtf are y’all doing? Lmao

[@CaptOrlandoMuniz]

Lol. I hate masks too!! 🤣 This was done during the height of the pandemic. Lol