Store - www.Rustyphat.co.uk In this video i talk through how to fit a front splitter to your corsa VXR. They are great for your money and lower the look of your car without touching your suspension!
Пікірлер: 58
@79johnnykage7 жыл бұрын
Nice one mate.. your car looks real well good looking opc/vxr 👍
@jakeyje3 жыл бұрын
so did you not have to drill any holes? recently bought a nurburgring splitter for my vxr and i really don’t want to drill any holes in her 🤣
@A_Gta_Addict7 ай бұрын
5:17 Hello, where did you get the blue interior stuff from, or was it standard on the car ? (The stuff like on the door, ect)
@RustyAutos7 ай бұрын
I painted them mate, think theres some really old.videos on them
@A_Gta_Addict7 ай бұрын
@RustyAutos Much appreciated, thank you. Love the look of your car by the way 😎💯
@1980orangeman7 жыл бұрын
OK thanks for the reply. Can you upload the installation of side skirt extensions video. As the front splitter install seems quite straightforward. With side skirt extensions I can't see how the nuts will be attached to the screw, without taking the side skirt off to hold the nut in place?
@RustyAutos7 жыл бұрын
1980orangeman I don't have the side skirt yet mate it is a future project so a video will come eventually for that but I am just looking into a new exhaust system at the minute, but once I do get one I will put a guide up
@1980orangeman7 жыл бұрын
OK thanks again for replying. (My car isn't lowered). So you say screw & bolt the front splitter just incase if impact . Side skirt extensions - could be 3M tape and self tapping screws?
@RustyAutos7 жыл бұрын
1980orangeman I'd say you would probably get away with it on the side skirts however, be careful I don't drive over anything again or get it caught on a kerb or it will rip it straight off
@1980orangeman7 жыл бұрын
Yes it is a concern but I'm not lowered, also I'm an SRI so I think 2cm higher than VXR. Generally I just want a sportier look (not VXR replica) as it isn't one. As you said in the video a splitter with side skirt extensions all the way round will look good. And unique as I haven't seen it on a corsa yet.. My side skirt extensions are MAXTON DESIGN & it is very thin & light. One last thing, do you think the self tapping screws will damage the side skirts & do you know if non rust ones are available? Thanks
@RustyAutos7 жыл бұрын
1980orangeman it will look sick on an Sri!..the self taping screws won't crack the side skirt as it is fibre glass it should just make nice holes and hold to it securely, just make sure when ur putting it on it won't damage any wires etc where every they go in to hold it on
@kevi22225 жыл бұрын
Well put together. Very nice looking car. Thank you.
@1980orangeman7 жыл бұрын
Hello - Good video! I have purchased the side skirt extensions & about to get the splitter. I'm wondering if you can install both with 3M tape self tapping screws & no bolts. What do you think?
@RustyAutos7 жыл бұрын
If i am honest i wouldn't risk it, the slight bump could tear it off and if your travelling at a high speed and you have to go over something in the road like a "shoe" (weve all had it) it will tear it straight off with how low it makes the car. your suppose to put adhesive tape inbetween any parts that dont join directly to the bumper aswell as the screws anyway, but i really wouldn't do it without the screws, and my advise is get bigger ones than they send you
@arsalan7x7206 жыл бұрын
What splitter is that and where can I get it?
@AshJD947 жыл бұрын
Love the videos mate! Hopefully picking up my ARDEN blue VXR tomorrow, and I'm planning on doing things like wrapping the vents and spraying the interior parts. Might be a silly question, but do you need to declare these things to your insurer? When I quoted insurance with modifications it jumped to something ridiculous like 6k lol! I'm just weary of making a claim and them not paying out because I didn't declare that I'd wrapped the vents or sprayed the interior? Cheers in advance bud!
@RustyAutos7 жыл бұрын
AshJD94 alright mate yes you would have to declare it as they are classed as modifications from the standard car
@Rxyimm7 жыл бұрын
Nice! would you consider getting your brake lights tinted black, it would look sick on your Corsa? :D
@RustyAutos7 жыл бұрын
Rayim Ullah yes mate this is a future project for me, I'll upload a video on doing that too. I've currently ordered some carbon fibre wrap for the inside centre colum where the radio is so hopefully gonna have a play around with that and a video will be coming for it!
@jayph88867 жыл бұрын
hiya pal is your vauxhall badge painted for wrapped does it just come off with hot water and credit card? ive also got arden blue corsa im loving the look of yours!
@RustyAutos7 жыл бұрын
Jamie Hunt yes mate it is literally just taken off a and sprayed :) thanks mate appreciate it
@79johnnykage7 жыл бұрын
Your videos are good but you actually never really showed how you fit your front splitter you just skipped all the important parts like the drilling how many holes you needed to drill to keep it secure... looks mint mate
@RustyAutos7 жыл бұрын
john quinn if you watch the whole video I show u where the bolts are on each side mate
@rafiasadiq23667 жыл бұрын
Great videos keep them coming 😊
@vScoobyDoox7 жыл бұрын
Love it mate. You not worried about it ripping the bumper to pieces if you catch it on something?
@RustyAutos7 жыл бұрын
vScoobyDoox the splitter itself has a very very thin piece of plastic underneath that scrapes..so it's not a large surface for it to scrape on only way I'll rip it off is if I drive too close to the kerb when I'm parking but I always reverse in the bays haha
@79johnnykage7 жыл бұрын
Just I have the same splitter got it the other day and with 16th bolts and I was like where do all these go... haven't fitted it yet looks easy enough!!
@RustyAutos7 жыл бұрын
john quinn it is a simple mate it is literally drill through a and put your bolts and washers through...it is that simple
@Pkdimmock4 жыл бұрын
Did it scrape a lot more after putting this on? I want to do one but not sure.
@RustyAutos4 жыл бұрын
Yup haha
@MrMonster9817 жыл бұрын
How many of the bolts did you put in? I know it comes with the 4 holes to show where to do them but did you add any extra ones in or did you just use the standard 4??
@RustyAutos7 жыл бұрын
i used the standard 4 however, think of this as the spilliter __I__I__I__ where the verticle lines are i added one bolt into each one of those to make sure it stayed connected in the middle
@jayph88867 жыл бұрын
how easy was it to take the grill out did you have take bumper off?
@RustyAutos7 жыл бұрын
Jamie Hunt which grill mate? as the top grill can't be removed unless its actually cut out, I believe the bottom ones comes out as the bumper is in two parts (one at the bottom below the fog lights) and above
@thedailyforzalife87377 жыл бұрын
Is that the default spoiler painted black??
@RustyAutos7 жыл бұрын
The Daily Forza Life yes it is mate :)
@curtiswright93254 жыл бұрын
Have you got a link for the splitter?
@RustyAutos4 жыл бұрын
I dont mate anymore they changed the designs
@thedailyforzalife87377 жыл бұрын
How did u get the fog lights in a black casing?
@RustyAutos7 жыл бұрын
The Daily Forza Life these were taken out and sprayed :)
@kanielwoodward97087 жыл бұрын
enjoying these videos mate, keep it up 🖒
@RustyAutos7 жыл бұрын
Kaniel Woodward cheers mate really appreciate it!
@arsalan7x7206 жыл бұрын
What splitter is that and where can I get it?
@RustyAutos6 жыл бұрын
This splitter ended up breaking on me, so I got one from triple r composites and the process of installing is the same but quality is alot better
@jayph88867 жыл бұрын
is your bonnet wrapped?
@RustyAutos7 жыл бұрын
Jamie Hunt painted mate but very very easy to wrap
@stephenismay-johnston2117 жыл бұрын
Oooo she is looking very lovely :)
@RustyAutos7 жыл бұрын
Stephen Ismay - Johnston slowly mate! wrapped the slits/ vents on the bumpers today in gloss black, video going up soon
@rafiasadiq23667 жыл бұрын
Is it easy to set of in this car and is it petrol
@RustyAutos7 жыл бұрын
yes it is easy to set off and yes it is petrol, however i have to be careful in rain because there is too much torque on the front end which makes it spin
@rafiasadiq23667 жыл бұрын
Rusty Phat ok thanks is it similar to a diesel how they set off
@madmark2726 жыл бұрын
How did you attach the middle of the splitter as no clearance underneath to get bolts on?
@RustyAutos6 жыл бұрын
madmark I went thro the three vertical bits that do touch thro the car instead :)
@madmark2726 жыл бұрын
Rusty Phat I have drilled the holes through the 3 parts that that contact the car. how did u connect the bolts as you can't get to them due to bumper underneath is in the way with 3 screws. I removed them and still can't reach to get bolts in?
@RustyAutos6 жыл бұрын
madmark when it is jacked up you can reach your arm over to put the bolt on, I didn't need to take the bumper off for it, i could fit my hand to the other side
@madmark2726 жыл бұрын
Rusty Phat OK will will have another look cheers also mine looks about same height at front with splitter attached do you clear speed humps no problem or does it scrape?
@RustyAutos6 жыл бұрын
madmark I clear most but if there's a drop before it scrapes