Fix Canon Printer Error 5200 (3 Solutions)

Learn how to fix Canon Printer error 5200.
One of the common causes of the Canon 5200 error code is that after refilling the black ink cartridge it still shows the error code.
There are several reasons why you get this error code. Please look at all the different solutions and see if you could remove this error.
Watch this video for 3 different solutions you could try.
FOLLOW US ON TWITTER: bit.ly/10Glst1
LIKE US ON FACEBOOK: on. ZKP4nU
FOLLOW US ON G+: bit.ly/WfMmZN
www.itjungles.com
Visit Android Forum for Discussions: www.androidsnap...

[@reviewsandfun]

THIS WAS REALLY HELPFULL EVEN IN 2024!!!! Kudos !

[@GayAlson]

I can't thank you enough! I was ready to go buy a new printer but Solution 3 of your instructions fixed my Canon MP490. I did have to modify Step 4 a bit. Pressing Stop 5 times didn't fix, tried pressing 2 times as someone else suggested, didn't fix, then tried pressing it 3 times, got a blank screen labeled "Service Mode", followed all the rest of your instructions, and VOILA! I have my printer back. Hats off to you, sir! :) :)

[@alhrmodemin]

thank you guys!!! got the same issue with the MP940 printer..I pressed the stop botton three times instead of five and it worked. thanks again!!

[@melbendigo]

None of these worked for me, but I found the solution on a forum. Flushing the ink from the Maintenance panel fixed it.

[@jgk7817]

I just fixed this problem (Error 5200) on my PIXMA MP490 using a slight modification of the third reset method mentioned in this video. The procedure that worked on my printer is: Turn off your printer Press and hold the STOP button (red circle/triangle) Press and hold Power ON button While pressing the Power ON button, release the STOP/RESET button and then press/release the STOP two (2) times Then release the Power ON button. At t his point the printer should go into service mode. The LCD should go white and display "service mode" at the top. Wait until it displays an “idle” message. It will take a few seconds When “idle” appears, open the top cover to expose the cartridges. Open the cartridge covers, remove both, then close the cartridge covers. Close the top cover and turn off the printer Turn on the printer and after the printer initializes, reinstall the cartridges. You can quickly test to see if the Error 5200 is gone now by trying a copy (just press the Black Start button to make a copy -- the button with the white diamond + vertical line). The key to clearing this error is finding the steps to getting the printer to enter its service mode. Good luck.

[@criss6945]

I fixed this 5200 error by going to printer's Settings and fixing the wireless LAN connection, introducing the modem password again. Before that, in Windows (Printers & Scanners) the printer appeared offline. After that it no longer showed offline and the 5200 error stopped showing, I was able to scan and print again, yay.

[@diytatay4991]

I tried everything here for my mx492 with 5200 error but no avail, then I thought of blowing thru the refill hole until some inks came out....and it worked! Halleluiah!

[@timothymiller9966]

This was a great solution. It fixed my printer so it would at least operate, but wouldn't print any ink. Well, I just happened to have a new unopened print head so I put that in and filled the yellow ink tank that the printer said was low. Success, it now print just fine now. Thank you so much.

[@maeshellsaledesesto3938]

it didn't work but at least now I know the problem haha Thank God for people like you. Keep it up!

[@daviddad]

Thank you. Your presentation is clear and very user-friendly. It worked perfectly on my Canon MX350.

[@Zahumny]

Solution 3 totally works for my pixma 2700. Always come back to this video after ink refill. Thanks

[@kittilicious276]

I have a canon ip2700 and after following the solution 3 here it started printing again! Yay! Prior to that it was showing error 5200. I am so happy now!

[@Itjungles]

Glad you find it is working.

[@raregem8886]

Okay! This worked for me! I refilled ink in my cartridge and it did not recognize the changes. But, this method solved the problem! Thank you!

[@peggyadamick1381]

The video was done well. I was able to trouble shoot for my error code 5200 on the 2nd option. I do like the BLANK SCREEN notation on the slides and in your text. Your instructions are like making a hard power down and up on a computer. But this is for a printer. Thank you.

[@francinetandy506]

This is the second time I've used one of your videos, and it solved my issue both times. In this case, solution 3 worked. Error was caused by refilling the ink cartridge. Thank you!

[@evertvdwaa]

MY SOLUTION! I also had the error 5200 on my printer (MG3650). Tried all tips I could find, but to no avail. Then I noticed that the printer would copy with no problem at all. Next I tried printing from my smartphone, and that was no problem either. I started to wonder if the problem might not lie with the printer itself, but with the software on my computer (Macbook). I uninstalled all Canon software and reinstalled everything, and MY PRINTER WAS BACK ALIVE!!! Hopefully this will help some of you with the same issue.

[@BillC-64]

Never seen solution 3 before, and it worked. Shocked. Thanks.

[@karenkatmom3635]

Thank you, so much for the awesome directions!! I really appreciate the time you took to make such amazing directions. Sadly, none of them worked on my Canon G7020. As far as I am concerned, it is a $300+ piece of JUNK!! I am giving it away to Goodwill (IF they will take it!)

[@jasmineramirez5252]

Thank you for this tutorial. It helped so much. My printer is working fine again and no error message! 👍🏽

[@GlossGirl]

I was thinking I could just read the steps and get it but after watching you do it, it worked! thank thatnk you thank you!!!!

[@lhaskew2307]

I tried solution number 3 on my PIXMA MX 340 and it worked! Thank you, Thank you JESUS,Thank you!!!

[@calhounio]

#3 worked for me as well. Canon wants me to spend extra money on a color cartridge when all I need to do is change my printer settings to print in grayscale. You save money.

[@sarahmcfarlane5679]

Thank you, the third option worked for me even without replacing my colour ink! Very happy right now thanks!

[@Sea-rx3bh]

Thank you sir. It helps on my mp287 with error P08(printer) and 5200(computer). I only refill black ink and it still does work. Many thanks for the clear instructios and demonstation

[@mauricioblanco582]

Thanks, I have a Canon Pixma MP280 and I was thinking that I had to spend money to replace it, but it was enough to follow the text instructions for solution 3. :)

[@drzal8553]

Wow! KZbin instructions that actually worked for me!! #3 did the trick ...

[@michaelstonewall204]

You are the MAN.....followed your directions and BINGO! Thanks for the information!!!!!!!!!

[@starskyd5]

THANK YOU!!! Solution #3 worked for my cannon printer and right before I had to turn in an important paper for college!

[@samk5840]

YOU MY FRIEND ARE A GOD!!!!!! Thank you so much!!! Almost bought a new printer, but thanks to your very detailed instructions i was able to reset it!!! Thank you again!!!

[@markl4112]

I tried to only replace the black ink cartridge only. I replaced the color and resolved the issue. Thanks very much. I only need black and white printing. Is there a way to over ride the need for color ink??? Thank you!!!

[@shishirroy1516]

this is the only solution which helped me. thanks a lot.

[@ourenergyfuture]

00:26 My MP250 runs just fine when the color ink cartridge is empty and the black one is full. Use printer only for printing documents. For my use, color is not needed. Color cartridge has been empty for about four years and has never caused an error code after refilling the black cartridge.

[@flipatyfloop4504]

Nice video, thanks. My solution for this error on MX420 was printing colour would come out light grayscale. next step was to print nozzle check and no colour printed out. tried deep clean with all colour and Blk and the error appeared. Replaced the colour cartridge and that was the fault.

[@monikamszewczyk7734]

It worked for my Canon MX340. Thank you so much ☺️ You're a star!

[@AKLAZARNA]

MX340: #3 worked for me!!! (But I didn't follow instructions EXACTLY a couple of times and got nowhere. Then I read the comments and "Herg Lay" had success with MX340...so I tried again...EXACTLY)

[@goldace1093]

Hello bro , i have canon pixma g2420 with an error 5200 I filled the ink in each of the tanks, tubes and cartridge, but unfortunately the same problem is still present, and I also cannot control the commands via buttons ( menu...) on the printer or the computer program, because it shows me an error (printed sheet count 2451-2500) Thank you very much and please reply to my problem if you encounter this problem.

[@gdean6440]

I had a code 5207. What step should I do to get rid of? My Canon is Maxify - model MB2720. I opened the back door and front door to remove jammed paper but I still have this code 5207 after that. Thanks

[@user-nx7dj8ey1k]

Thank you so much!! Clear and easy to follow instructions.

[@thomascirignano]

What does error 5205 actually mean on a Canon MB 2720? And, how do I "Cancel Printing" when I was scanning and copying directly on the printer and not using my computer? I don't see any way to cancel the print job. Thanks.

[@neojoneswd]

i will try the 3rd Solution but i believe it is probably the ink cartridge issue. my black has been low, color shows about 1/2 but could be low ink is causing it. if number 3 fails i will change all cartridges. will change in either case to make sure 5200 is not mech error.

[@chucklambert5577]

Thank you; it worked the second time I followed your video.

[@contforall]

Thanks. It worked perfectly on CANON G2411

[@mmmarques]

That 3rd step worked like a miracle. thx a million!

[@InservioLetum]

The first time I tried this fix it worked, although at no point during the process did the leds react to my button presses. I've now worked out that pushing ON with STOP pressed activates the counter leds, which switches between green and orange each time you press stop. Once I release after the 5x STOP, however, the error pops right back up again. Worse yet, now it also shows up in my computer screen! Exactly which codes are there, because the blank printer screen never happened, the new device popup never happened, and I'm now using new catridges. HALP. SEND CHOCOLATE. AND HAMMER.

[@TeknixTrix]

Do you have the same 5200 cancelling procedure for the MG6360?

[@sderapino]

Thanks for video, problem 5200 solved!

[@juliocesardesigner21]

No meu caso havia um BISCOITO dentro da impressora causando o problema. Tentem olhar embaixo do carro (embaixo daqueles roletes do carro) pra ver se não tem nada preso lá. In my case it was a COOKIE stuck below the car thing. Take a look at the rollers

[@felixmurillop]

Awesome! worked perfect Bro! 0:56 Canon MX350

[@spaluny]

Thank you. Solution 3 worked as wired as it might be to press all these buttons ..

[@robdunn487]

Thanks for the help. Great . Don't know why the error code just doesn't say change ink cartridge - Double Dutch!!!!

[@retropickups2000]

SOLUTION 3 WORKED FOR MY MX350!! yessssssssir

[@tejasgupta6865]

LAST STEP WORKS.. THANKS A LOT

[@ChiragChaudhari]

Worked for me first try. I tried Solution no. 3. thanks.

[@cathyantunes8117]

Thank you! Number 3 solved the problem for me. I have a Canon MX340.

[@jesusfreak5535]

This fixed my problem! Thank You a lot, from Sweden!!

[@isbiervirellacarballo6840]

Por favor, Necesito saber como corregir el error 5205 tengo una canon Maxify MB2720

[@monikamuller7540]

Thank you so much!! This is the only video that helped us with our Printer!!

[@robertquiambao1347]

The 3rd solution is simple and easy to understand,, works good to G100. Thank you for your tips.

[@KiranTaker270]

thank you so much i tried everything to fix this annoying code now it runs like new as i only had my MG4250 for a few months

[@headcoach88]

Solution 3 works for my MX340. Thank you

[@stephaniekie1552]

Solved on my MX347. Thank u so much

[@DanielsGameVault]

Can't seem to get the code right on my Mx320. After I go through the sequence the printer just powers on like normal...

[@szvw]

1:00 Solution 3 worked perfectly for my MX535 / MX530

[@MsFlorinnn]

Solution 3 worked on Pixma MG2250. Thanks!

[@rahmanayman4002]

thanks. solution three worked for me but now id have to change the cartridges my printer thinks they are empty Canon Pixma iP2772

[@diemuckedeslebens]

Number 3 did the trick! Thank you very much!!!

[@littlelucee319]

Solution 3 worked for me. Thank you so much! 😊

[@rallainelota963]

Thank you! Your solution 3 worked!

[@npuffy]

Finally fixed the error. Many many thanks!

[@priyauk1]

Thank you this worked for me!! you are a star

[@iamyou1972]

None of the above are working for error code 5206. My printer MB 2320 is going to be rejected. Please help me to get rid of it.

[@triumphtv3]

Thank you sir! The video demonstration for Solution 3 was very helpful.

[@TheMagista88]

CANON MG6320 ALL TOUCHSCREEN MODELS) FIX: 1. HOLD STOP/RESET FOR 5 SECONDS 2. WHILE STILL HOLDING DOWN, PRESS & HOLD POWER BUTTON 3. KEEP HOLDING BOTH FOR ABOUT 5 SECONDS THEN RELEASE THE STOP/RESET BUTTON 4. PRESS STOP/RESET BUTTON 4 TIMES THEN RELEASE POWER MESSAGE WILL DISAPPEAR

[@jasminabanks]

Thank you so much, I used solution 1&3 together and it works perfectly now. Save me so much time. I was getting frustrated asf lmao I have a canon MG3620

[@yottasang]

thank you very much. worked for my PIXMA G2000

[@MamaMama-gw9df]

Dankjewel, voor mij heeft het gewerkt

[@sheikhhammad8687]

Halo I have try this method but in my printer show this still Error code 5200 And black ink run out I have both inks filled. Do u have any other solution for my printer. I print or copy any page come blank page out😑

[@lacychaugan]

Thank you very much for this helpful video!! The third option worked for me!

[@Mannymavy]

Thank you so much, works for my canon MX 340

[@sergiogonzales6452]

Thank you very much my friend, you have taken a big problem off me, I send you a big hug and I wish the best for you, God bless you.

[@navinramjattan7308]

Thanks for the video . The 3rd Solution helped me out

[@karimbelacel6323]

toujours le code erreur 5200 s'affiche même les 3 solution nom pas réussi avec canon MG 5750 pour vous informer Jai remplacer la tète neuf le même problème

[@dave777aw]

Thank You so much. Worked great on my mx340.

[@jenniferluzana6650]

is it work for pixma mp237,, with the same error 5200

[@noealva]

Thanks! I didn't think it would work but it did.

[@Chatzkies]

My Canon computer has an override for and IS able to run only with black or color. Been running for month just like that

[@aramtaylor8346]

I dosent work for me i try 5 time and put new ink is there any other way to fix it.

[@crystalgreene4173]

Thanks a lot! Solution 3 worked! I have an MP495 canon.

[@ginger6907]

Fixed my MX340 as well. Thank you for sharing this information!

[@sapoty]

The way you pronounce button sounds like a very English expletive. 😄

[@gosteronlinecourses]

Thanks good buddy. 10-4 over and out.

[@jimdoyle8914]

Can’t get rid of error 5200 on my mp500 printer. All 5 tanks are new full Canon tanks

[@gyromatical]

because unplugging stuff magically fixes itself amirite

[@thomasvschwarz9705]

Thank you ... method two worked perfectly!!! Thank you

[@pvgua]

Thank you very much, solution 3 is great.

[@BlakestonJean882014]

how do i find THE PRINTER ALIGNMENT DIALOG ON MY CANON 5250

[@herglay5170]

Solution 3 worked! Thanks so much, I also have the MX340

[@bakrimisaid7069]

I fix my canon pixma g3420 error 5200 by ink flush in maintenance option in the menu

[@hydenrobinson4001]

Thanks. Worked perfectly on my MX340

[@Itjungles]

You are welcome. Great to see it works on MX340.

[@DocumentodeViagem]

solution 3 works for canon mp495, thanks a lot!

[@denforundrade695]

Solution number 3 even worked on my older MP280...:P

[@Bluejayprowash]

thank you so much this is great it worked on my beast !