I was having issues with very poor idle and dying after throttle was applied then released. It turns out it was the throttle override switch. This can cause intermittent or no spark.
Пікірлер: 42
@jttrclub2 жыл бұрын
Thank you I’ve done so much carb adjustment after I rebuilt it. I did a whole rebuild of the four wheeler from sitting after 15 years and this saved me
@zzbudzz2 жыл бұрын
Thank you! I was in the garage working on my 300 xplorer trying to figure out why it just will not idle and finally giving up for the day and looking to buy a new carb i found this!. My throttle insides are a little different and has a different contact device. I put a small piece of thick paper between the contacts and pressed the start button and it started up like new and idled fine ! I would have never thought of this without seeing this video. THANKS AGAIN
@markhanson798Ай бұрын
I have the same exact 4. Wheeler was running just fine 2 days ago. Pressure washed it and had no spark. Found this video, and the issue is fixed. Thank you
@brandonkriesel8856Ай бұрын
What cords did you cut?
@Erix7810 Жыл бұрын
God bless you bro for making this video. Thank you.
@user-wc1go4hw9z10 ай бұрын
Awesome fix on an old Polaris Hawkeye 300 Thank you!
@fosman1799 Жыл бұрын
Just pick up an old 1997 500 Xplorer poor idle just pulled red white wire off beautiful thank you .
@tmel4198 Жыл бұрын
I have a 96 500 Sportsman. What wires did you pull, from the board or at the ETC switch? Thanks!
@fosman1799 Жыл бұрын
The red white wire down from switch 👌
@MrSteeda1 Жыл бұрын
Going to try this tomorrow thanks
@ArizonaKid3 жыл бұрын
I’m sure it will help someone, good info
@Whitestrash3 жыл бұрын
I hope it does. It kicked my ass!
@conradhomestead4518 Жыл бұрын
If only we had more mechanically capable squirrels in our area
@pedritoc.c.t.66510 ай бұрын
Great video . Question I just got one with 1600 Miles was in a barn cince 2011 . There is no lights no break lights only shifter I doctor and runs ok idle little rough. But it does burnouts pretty good . Any idea what it could be ?
@Whitestrash10 ай бұрын
It could be so many things. I always start with cleaning the carb and going from there.
@mr.octopus6972 Жыл бұрын
You can be dump as a squirrel and cut the wire OR you can unplug it flom the board... Anyways thank to you I just found out that little bend aluminium piece pressing the switch is broken on my atv. Can't be repared so I'll bypass the system. However it didn't fix the problem I'm working on, it's running fine on idle but when I hit the gas it backfires from the muffler and wants to die...any ideas where I should look ?
@Whitestrash Жыл бұрын
Pulling it from the board is an option, but not nearly as easy as cutting the wires. Your issue could be carb related or possibly the ignition timing is off.
@mr.octopus6972 Жыл бұрын
@@Whitestrash thanks I'll try looking at the timing 👍
@ediwaldosanchez7268 Жыл бұрын
1 Check the carburetor intake boot for cracks 2 replace old reeds before making any carburetor adjustment 3 make sure your oil injection pump is not dumping too much oil once you adjust it take a ride on it come back and make sure it's still adjusted properly 5 Does your throttle move easily if it doesn't just replace the whole throttle cable it'll give you way more problems than it's worth (On a side note make sure your battery is fully charged even though you can run these machines without one they'll never run right)
@Splitshot1 Жыл бұрын
Thanks alot,...Found a squirrel mechanic- haha.
@MrSprintcat Жыл бұрын
I'm not sure but it seems like you could just cut the one wire at the switch.
@Whitestrash Жыл бұрын
You're probably right.
@MrSprintcat Жыл бұрын
@@Whitestrash thanks for the reply. I actually think I might be having some issue similar to that with the high low neutral reversed shifter. Unless I hold slight pressure forward it won't go into four-wheel drive. Or should I say it won't send power to the front hubs
@HellzJester19 ай бұрын
So in theory I could put those wires on a switch yeah?
@Whitestrash9 ай бұрын
I guess you could of you wanted to.
@codycutter81822 жыл бұрын
which wires need to be cut
@Whitestrash2 жыл бұрын
Just the 2 wires inside that throttle box. Cut and tape both wires, isolating then from each other.
@Finlan20059 ай бұрын
Will this work on a 1989 trail boss 250
@Whitestrash9 ай бұрын
Most likely. It's worth a shot!
@davidferency33399 ай бұрын
my 400 dose just the opposite it will idle rough but it will not throttle up just dies out
@nickgoar55896 ай бұрын
Same here
@dscanadianoutdoors32574 ай бұрын
Would this cause a no power to dash issue? Got a 94 sportsman 400 and that entire etc area is corroded really bad.
@Whitestrash4 ай бұрын
Probably not. It's gotta be something going to the dash. Those power distribution boards are a poor design. They corrode bad.
@dscanadianoutdoors32574 ай бұрын
@Whitestrash I found a broken brown wire, going to trace it tomorrow.
@Whitestrash4 ай бұрын
@@dscanadianoutdoors3257 brown is usually ground on polaris.
@Whitestrash4 ай бұрын
@@dscanadianoutdoors3257 brown is ground on polaris. Just get that broken wire to a good ground.
@dscanadianoutdoors32574 ай бұрын
@@Whitestrash appreciate the help
@AlvaroGarcia-kf3ih Жыл бұрын
The squirrel 🐿 in my neighborhood won’t help 😂😂😂
@wayne6525 Жыл бұрын
I get sea sick following the camera around...
@Whitestrash Жыл бұрын
I hear ya.
@conradhomestead4518 Жыл бұрын
If only we had more mechanically capable squirrels in our area