Fixing a Pocket Digital Scale that Won't Calibrate

[@BeatBum805]

Gotta thank you for this man. Mines fell, and when I turned it on it didn't work. Thought I had to get a new one, but thought I should try searching it up, and I came across your video. Took it apart, and put it back. Re calibrated it, and bam! all good. Thank you!

[@ZacharyMelo]

BeatBum Gaming sometimes all you need to do is take something to bits and re assemble it to get it working again.

[@businessoutsidethelines]

Thank you... This wasn't what I needed but seeing you do it put me on the right track and my scale works fine now.

[@ZacharyMelo]

That's awesome to hear. This is why I pull out the camera and record my work sometimes. Good luck in your future repairs.

[@businessoutsidethelines]

@@ZacharyMelo Maybe I should do the same thing. The art of "figurin' stuff out" seems to be lost these days. Oh, also, I actually posted the steps to recalibrate it on the Amazon.com page where I bought it! Hopefully saving others the struggle I had!

[@omarjunaideen3609]

Yo fam! My scales a mh series, the weight is stuck on 0 even if I add weight to it. Any idea if it's fixable?

[@iBRCKsHD]

never worked, mine is soldered to wires and its too short to flip up side down..

[@elguapo6458]

I got mine wet and it won’t weigh now it’s always at 0 do you know any fixes for that

[@JohnyIIOh]

Open it, clean it with alcohol and an old toothbrush (we try to clean of corrosion bridges). If this doesn't work, resolder the connections with a soldering iron (if you have one). Hope that helped

[@elguapo6458]

@@JohnyIIOh I appreciate the help but I threw that shit out mad long ago

[@stevehumphries6979]

my usmagnum1000xr digital pocket scale is not working. The scale when turned on shows a flashing cal and that's all it will do. Can you help me fix it.

[@tacozila1127]

Calibrate it

[@Thatsmessedupman]

Any idea why a digital pocket scale will calibrate with a 50 g weight but when you tare it will always show a negative number not zero. Is that due to air pressure or is my scale going to be off by the negative value shown?

[@ZacharyMelo]

It seems as if your scale isn't actually calibrating. The circuitry is likely faulty, being unable to hit its zero point reliably. Does the number continue to move lower after being tared? It's certainly not air pressure, but you may be able to do some simple math to account for the error. Try weighing your 50g weight after tare, what do you get? What about a smaller tar weight?

[@shawneesuttle5634]

So i just bought my scale and tared it to 0 then tried to calibrate but the weight is still wrong. It’s telling me a penny is 11.9 grams. Pennies are 2.5 gs. I don’t have a silver top just the little black box ones. Do i need to take it back and get s new one

[@ZacharyMelo]

Are you sure you followed the calibration procedure correctly?

[@reddrgnlrd]

Ingenious idea! Good job!

[@Snippydust]

My scale kept giving me erratic readings, so i tried to ripen the plate off with my hand, but i realized it doesnt come off the same as yours, so i pressed it back on, and then the scale works perfectly now

[@nenadteskeredzic7341]

Why is it on the display after the second attempt again -- 5.56 ??

[@dubbzmack9042]

Thank you sir.. who would think sumn soo simple wouldve been the problem.. awesome an perfectly understandable

[@letsrok713]

Thank you for this.. My scale was calibrating low so i took apart cleaned and put back together, Waalaa!! Working again

[@witblitzracing_fx691]

I have the scale you have at the end of the video and it stays on 0. It wont weigh anything?

[@ZacharyMelo]

Can you do a calibration?

[@Tj1056]

do u know how to fix a scale that just shows HHH when turned on?

[@commonobject3468]

+Tj1056 The scale is likely out of calibration or has a circuitry fault. Try calibrating, and if that fails - disassemble and reassemble.

[@danielpullen5555]

How do I get past the (over) code to recalibrate

[@Keegan_0727]

I took the silver top plate off of my scale and the part screwed on. How do I put it back together

[@justinoconnell4612]

My scales are brand new and saying 26.6g when I put a penny on when it should weigh 3.5g? Help please...

[@ZacharyMelo]

Sounds like you are in need of a calibration. That's a whole different process.

[@justinoconnell4612]

@@ZacharyMelo I calibrated them and ever since it says the wrong weight. Is there anyway to reset them?

[@ZacharyMelo]

@@justinoconnell4612 calibrate with the correct weight. If calibrated with an incorrect weight, they will never read correctly. If they cannot calibrate from a brand new state, return them.

[@justinoconnell4612]

@@ZacharyMelo ok I will try and send back if don't work thanks Zac 👌🏽

[@snakev10v5]

I have an SWS100 pocket scales, and I was calibrating it earlier. It was working fine after it, and then it turned itself off (Auto off future) but when I turned it back it showed "FULL" I am new to these things, so what's the problem and how do I fix it?

[@jasonoreilly2884]

snakev10v5

[@blackshannon573]

What weight 100 g

[@Dontlook146]

What happens if you drop it? It still measure a penny @2.5g, but it fell pretty hard..

[@ZacharyMelo]

They are simple machines, and should not suffer too much from a fall.

[@wendwag1970]

Not all pennies way the same amount ..

[@skan8]

Anyone knows if it's fixable when the weight measurement starts going up by itself ?

[@ZacharyMelo]

Have you tried changing your batteries? Is the scale on a flat and level surface?

[@skan8]

@@ZacharyMelo the scale is new witn new batteries . I did all conventional instructions .

[@ZacharyMelo]

@@skan8 it sounds as if the scale is defective. Have you tried going through the calibration process in the instructions for your scale? Have you tried different batteries?

[@skan8]

@@ZacharyMelo I did everythig , I even found some hidden settings .

[@TrustNoHUMAN420]

my scale base doesn't come off like that one and it keeps reading negative and I did all the settings and used the 5 nickles and it's reading 258.8 grams. it's a us-750EX

[@mrfiesty505]

It looked like it didnt work. Cus it read 5.59....or something close to that.

[@ZacharyMelo]

The kitchen scale says it's a whole number weight because it's rounded to whole grams, whereas the pocket scale weighs in one hundredth of a gram increments. The scale needs to be re-calibrated after this type of repair to ensure accuracy - I'm not weighing a loonie if you were expecting the classic 7g test.

[@davidmclean1623]

The sound cuts off half way through the video.

[@nekikepec9241]

how to fix out2 problem it wont go throught calibration

[@northernlights1870]

My scale says a nickel ways 20. something grams why is that

[@TeeAndSee]

Mine won’t turn on at all

[@aci344]

i just bought this scale and it starts up and only says "out2". I have never used it before and i cannot calibrate it. It just doesnt seem to detect any weight

[@jerretcook3907]

how did u fix it?....

[@oanailiescu81]

It worked!!! Thank you!

[@trichomelover4209]

thanks

[@trichomelover4209]

if i didnt see this video i would have lost the deal today :D need to deliver some goodies from scale

[@brendanthompson7444]

DOES ANYONE NO WHY MY SCALES SAY FULL AND WONT DO ANYTHIN ELSE

[@commonobject3468]

Look up the model number to find more information and a user manual, then try to re-calibrate. A reputable brand name product will have a website or phone number with useful information.

[@dannyhubbard7346]

Common Object dz5-100

[@damirsoldan7848]

Best advice my bro

[@outrobeatem8887]

I could apart ufo or hornet and put all parts back together. Then give me alarm clock and would broke it by setting right time. MeGenious

[@mulagaming1789]

still just blinks didn’t do anything

[@LX2709]

Thank you brother

[@tycenmercer9839]

Why would you tell me to pop the top off it js broke when I did that

[@ZacharyMelo]

Why would you blindly follow a KZbin video without applying your own critical thinking? Did you see how easily I break mine down? You obviously forced it and are upset, but me making a helpful video doesn’t make your mistakes my fault. Good luck with your repairs. Maybe you’ll figure out how to fix the part you broke, and make a video for some ungrateful cus to complain under.

[@jaxxoncolledge9253]

Can I get a sack?

[@leannscott7309]

I should have knew better my scale did not look exactly like yours so I should not have tried this my 2 screws was actually underneath where the batteries go and I just broke my scale 🤭

[@Kashdream16]

Yes, there are 2 down there pointing up, and 2 up under the plate pointing down. All 4 must be removed to adjust the sensor.

[@thescreamingmonkey]

thanks it workx

[@johnotto4586]

i have seen 100 posts all over the web and a bunch on this feed even with the same problem i have, i calibrated them and now they say full, you can't push anything except on and off, there isnt one gd solution anywhere, everyone just ignores the question, is there anyone with enough fu--in sense to know what this means? if you dont answer this then you dont deserve a video, be the one scale guru that doesnt say, oh um look online, tried it, and its useless

[@ZacharyMelo]

john otto you don't even name your scale mfg or model. I'm not your employee so don't act like I owe you anything. Continue your research and quit blaming everyone else for your scale problems. When you solve your problem, make a video and help the community. I'm not a scale expert, just a tinkerer.

[@jasonoreilly2884]

Zachary Melo

[@jasonoreilly2884]

john otto Hey john i,ve the exact same promblem with my scales. The make of my model is MYCO. Could you please help me out with this matter if you know how to pal...

[@dadephunt1717]

It says fill because its over weight. If it isn't holding anything up but still says full then use your brain. The pressure sensor must he compressed right? Lol. Either the sensor is crushed and needs to be fluffed out to up crush it. Or something is keeping it heavier than it should be. How much weed crystals have gotten Inside, maybe it'd gummed up into a downward direction, making it think there stuff on it

[@ginopaul6]

Can you help me please? I tried everything and didn’t change anything.. My Fuzion 200g x 0.01 was working well, always asked for 100g calibration, today I wanted to recalibrate, and it asked 500g instead. Now when weighting it is saying 0g. My rockstar can is 4.6g…. When trying to recalibrate, it asks again to put 500g, but when doing so, Err E code appear and it closes. I’m pretty sure there’s still something to do with that scale. 😅 I don’t want to throw it away and buy a new one. This one was working A1 until it decided to ask me to calibrate it with a weight higher than what it was meant to weight (200g)

[@aziziismail3704]

Why my pocket scale not display 3 (0.00),. But hes display 2(0.0)g... Why