Fixing ALL THE THINGS! - Case 1845c Hydraulic Cylinder Rebuild

The chickens get moved again! They are almost at the end of the fencing so this will be the last move and the fence with get moved next time. Also, the hydraulic cylinder on the Case 1845c got fixed! Things are moving along!
Things in this video (affiliate):
Case 1845c seal kit (Bucket cylinder) - amzn.to/2MWviro
Seal Twistor Tool - amzn.to/2NpeF6t
Related videos to check out:
Time to GET IT DONE! - • Time to GET IT DONE! -...
Our chickens moved onto GREENER PASTURES - • Our chickens moved ont...
Music in this video:
Your Love by Ben Winwood - artlist.io/son...
A little about us:
In September 2015, our hearts were hijacked with the dream of living on a large farm, with community, growing food, caring for animals and loving on children in need of care and healing. It was a God moment, where our dreams collided with His dreams… a dream so big we could never do it in our own strength and wisdom. Since then, we have been on a journey to see that dream become a reality. This channel documents that journey.
Instagram - / goshenfarmandgardens
Facebook - / goshenfarmandgardens
Website - goshenfarmandg...

[@shanebrown5935]

The long chrome-plated rod is called the piston rod or ram. The small round piece bolted on the end is the piston. The threaded piece that screws into the barrel is the gland.

[@keith1535]

Thanks, you gave me the confidence to tackle my cylinder. Best Keith

[@GoshenFarmandGardens]

💪

[@adambauman8044]

He starts actually working on the cylinder at 7:55.

[@goldtinkerer]

Don't forget to remove the locking set screw before attempting to unscrew the gland from the cylinder.

[@mattpingel7742]

Great video!! Thanks

[@hollymorrison7793]

Jack of all trades...& Diligent

[@davek6630]

I’m not sure if I would use a synthetic blend of oil. It calls for 10/30 and that case additive. Though I was told that JD hytrans fluid meets the specs

[@fredolygrigs]

they make air tools that are much stronger if you move up to 3/4 or 1 inch drive

[@southernyankee1519]

Great video thanks

[@GoshenFarmandGardens]

You're welcome, thanks for stopping in!

[@johndalton9907]

How did you get the ram off the machine? I can't see how it comes off.

[@VolvoGonzo]

It looks like from the foliage that you made it through the winter and fixed it in the spring? How are you able to get by with it being down so long?

[@hawaiiansunrise8984]

You can just use AW 68 hydraulic fluid, it's cheaper and totally fine from what most guys say on KZbin

[@peterboissiere9684]

I have a harbor freight 3/4 breaker bar that would remove the bolt.

[@GoshenFarmandGardens]

Unfortunately I couldn't use a breaker bar because I was already afraid of bending the Piston.

[@peterboissiere9684]

Wow, I don't think u would twist the piston

[@GoshenFarmandGardens]

You're probably right. I tend to over think things 😂

[@markgarges3812]

Can you be more specific on the additive

[@GoshenFarmandGardens]

The HTO additive?

[@hawaiiansunrise8984]

You can use AW 68 instead and it's supposed to be totally fine

[@Hiperf]

Just use rotella HD tractor fluid. It has the case specs already so no additive needed.

[@Bubba54321]

It's called a zirk fitting that was missing.

[@larryantoine8490]

Wish I would've seen how you put them on.

[@GoshenFarmandGardens]

I can help answer any questions if you’re stuck.

[@larryantoine8490]

Just wanted to see what tools you used. And if I scratched the surface would is cause a problem?

[@GoshenFarmandGardens]

I used just a pair of channel locks to unscrew the cylinder cap, pulled the position out and used little screwdrivers and picks to get the seals put. Then of course the seal twister kit to get them back in. Yes you don’t want to damage or mar the piston it will cause problems for your new seals later as they run against it.

[@DumbCarGuy]

you should move to MN

[@leewehrhan3800]

It would have been nice to see how you actually install the seals. You only show after it has been installed. This is not very helpful to someone who has never done it before.

[@luisruiz7186]

After changing mine out it won’t hold pressure and it will slowly tilt down on its own. Anyone else have this problem or know the solution?

[@GoshenFarmandGardens]

Maybe trapped air in the lines?

[@bethelhouse851]

Why don’t you use the press

[@GoshenFarmandGardens]

Forgot we had one! 😂

[@jayforbes3965]

Throw the red lil drinking cup bucket away!!! It doesn’t work!!! It’s a rip off!!!!

[@gregstevens2556]

Treat her r try ú up