Installation Kompressor Pulley + 30HP / 48HP ! Mercedes-Benz 180K 200K M271 - Eaton M65 - C, E, SLK

[@Matha1R]

Jupíííí ✊ konečně někdo z našich luhů a hájů kdo se věnuje w204 kompresor 🤟 Tahle modifikace mě hodně zaujala , už kdysi jsem se informoval na MB fórech ohledně menší řemenice ke kompresoru a bylo mi řečeno že jsem pitomec a ať nevymýšlím ptákoviny 😀 Je možnost tě někde na soc. Sítích kontaktovat a zeptat se na pár otázek ohledně kompresoru a celkově na info o tomto motoru ? No, opravdu mám radost že jsem úplnou náhodou objevil tvůj Chanel 🤟😎

[@sachsentom.]

ich verstehe zwar kein Wort, aber was ich gesehen habe fande ich toll!

[@MotorFlash7]

@sachsentom. Zkuste titulky ;-)

[@sachsentom.]

@@MotorFlash7 Thx

[@sachsentom.]

Hned jsem se na to podíval znovu, s titulky..

[@LukaVulic-iw3kc]

can you put a link where you bought it, thanks

[@GiuseppeBenfante-v9q]

Ciao, è compatibile con SLK R170 200K 192cv ???

[@MotorFlash7]

@Giuseppe Benfante Na R170 pasuje tato: kzbin.info/www/bejne/bGbYmaSJrK-hkNk

[@Tomxize]

Do you also happen to know if it's necessary to lock other pulley's like the crankshaft for example or is it safe to replace it without locking it? Because this I don't see in the video

[@MotorFlash7]

@Tomxize není potřeba blokovat. Nezáleží na její poloze vůči ostatním kladkám...

[@berkeyazc1803]

I did it with 1.6 kompressor, thx will i now get 30 hp or less

[@EduardoMartinez-wl1mv]

Please, Information. W203 1800cc Kompresor.

[@MotorFlash7]

@EduardoMartinez-wl1mv Write to: [e-mail]

[@tsvetoslaviliev6641]

Hello, wich are your impressions after all this time? Any problem with the supercharger? Thanks

[@MotorFlash7]

@tsvetoslaviliev6641 Everything works as it should...absolutely no problems ;-)

[@peterlabropoulos8753]

On the video you speak in czech so i dont understand, why did you cut the old pulley on the edges? Also if i understood well, you install the new one till the axle of the kompressor shows up? Thank you!!(i have bought the same pulley)

[@MotorFlash7]

@peterlabropoulos8753 Play the subtitles and switch them to your own language ;-)

[@ddanid877dpx]

Hello, which would suit me? I also have a c200 kompressor from 2008 and I don't know which one is the best

[@MotorFlash7]

@hiphopmusicchannelaquadia7565 Yes this pulley is for your car.

[@2migo]

Nice video! Is software optimization required? :)

[@MotorFlash7]

@2migo Thank you! Your question has been asked many times in the comments ;-) Not necessary.

[@2migo]

@@MotorFlash7 oh, sorry haha.. okay thank you! How much do you sell it for and do I need a new V-belt? :)

[@goganareklishvili1320]

u put the same belt?

[@MotorFlash7]

@goganareklishvili1320 yes

[@seo333]

With smaller belt wont we have more power?

[@fosforinen]

@@seo333Maybe, the belt would be tighter and therefore would spin faster. But because it already works with the original belt that could mean the car can tighten the belt automatically and a thighter belt could break something

[@andreismeu8197]

hello, I have a question and please answer me, if I already have the software, what do I do to rewrite it??

[@MotorFlash7]

@andreismeu8197 Get to the Brake for remapping...

[@Performancebase_NL]

Do you install an new belt to? Or is the stock size oke?

[@MotorFlash7]

@Performancebase_NL It's all in the video ;-)

[@javiar8171]

if i have a 2002 cl203 230 kompressor, the kompressor pulley kit and the crankshaft pulley kit, suits my car (sorry for the english)

[@MotorFlash7]

@javiar8171 This engine is only fitted with a compressor pulley...

[@jirimatyas4911]

Super práce. Šla by ta řemenice i na naftu?

[@MotorFlash7]

@Jiří Matyáš Díky ;-) No jasně. Jestli máš kompressor na naftě, tak efekt je stejný - Zvýšení plnícího tlaku

[@jirimatyas4911]

@@MotorFlash7 Úplně mi vypadlo z hlavy že mám turbo.Byl jsem unešený jak "jednoduchým" způsobem si přidat pár HP....

[@Rakocy22]

Ako to jazdí po nejakom čase? Žiaden problém? Žiadna kontrolka motoru?

[@MotorFlash7]

@puxmenxxx Bez závad a kontrolek žlutého kuřete ;-)

[@frantisekputz7087]

Kde sa to dá objednať alebo zakúpiť skôr objednať ďakujem.Ja mám e 200 kompresor salón. Má 186 koní

[@MotorFlash7]

@frantisekputz7087 Napiš mi na: [e-mail]

[@arturaspf2566]

30 HP without tune? w203/w204 and Siemens SIM4KLE ECU just bleeds that extra boost, because ECU controls it via recirculaiton flap (BOV) how much air can enter intake manifold. Its not standard mechanical bypass valve, as older cars had before, and it worked well, this cars like w203/204 have new supercharger systems and have BOV (recirculation flap), that means ECU can control air. Only you can get from smaller pulley is better throttle response and low-some mid range torque gains, but HP numbers cant change. Also tune for this systems is not easy and cost many $$$, because it needs damos files for tune and expensive softs.

[@RaulLazar]

I've done this to my car also and the results without tune/soft are there. Not 30HP, but definitely, is an increase (tested before and after on GPS and against on other 2 cars with same specs). Yes, you have better throttle response and low-some mid range torque gains. The recirculation flap (BOV) is fully opened at 0.78 bar. With standard pulley (72mm) you get max. 0.55-0.57 bar (you will never reach 0.78) but with 60 or 62mm you get the max. 0.78 (you could get more, but is not need it and ECU doesn't let you anyway only if you tamper some sensors). However, doing this (smaller pulley) and get the max out of it, you need the tune and a better exhaust system. The soft is not that expensive, for example, there is a german company who sell the soft specially for a 62mm pulley (for Siemens SIM4KLE) with only 100 euros and a good tuner, can write that soft for another 150 euro, at least in my country. PS: Just as an idea, on Eaton m65 on m271 you can't really call it BOV, because it's a throttle body, identical 1:1 with the actual throttle body, the only difference is that the throttle body stays closed and when you accelerate it opens and the throttle body from Eaton, it's the opposite way.

[@kirilokabakov6769]

@@RaulLazarHi bro! Can you link company pls?

[@PODCharon]

Ahoj. Konečně nějaké video o tomhle motoru! Moc díky! Určitě to bude stejně i na CLK 209 135kw že?

[@MotorFlash7]

@Robin Svoboda Ahoj, díky za komentář! Určitě sleduj, bude ještě spoustu videí s tímto motorem ;-) Ano 209 je naprosto totožná...

[@m3up_737]

@@MotorFlash7how Long have you driven the car with the mods installed? How did the oil look after the next change

[@MotorFlash7]

@m3up_737 Everything is absolutely fine ;-) Change the oil after 10 000 km.

[@無-b8k]

Can I install this m271 200k? Where to buy?

[@MotorFlash7]

@user-yt6ku4pb2b Yes, it's for the M271 engine. To purchase, write to: [e-mail]

Chtěl bych vidět co na to ložiska v kompresoru, která musí mít daleko větší otáčky, Olej v kompresoru také musí při těch otáčkách daleko více pěnit. A co na to ECU, která bude dostávat informaci o vyšším plnícím tlaku než je předpokládaný v určitých otáčkách. Myslím, že za ty následné problémy těch 30 HP nestojí.

[@MotorFlash7]

• Kompressor snese daleko větší zátěž než po této úpravě, tak že se není čeho bát a ECU si s novým nastavením ví rady a upraví hodnoty dle potřeby. Samozřejmě když se ještě optimalizuje mapa tak je výsledek ještě znatelně lepší...

[@불나방-l2j]

M271 engin supercharger EATON M65??

[@MotorFlash7]

@불나방-l2j • yes

[@불나방-l2j]

@MotorFlash7 Thank you bro~!

[@stanitodo1075]

Odkud jsi to koupil?

[@Metlosek3d]

​@@MotorFlash7 prosím hodil by jsi sem název výrobce, nebo link na zakoupení?

[@MotorFlash7]

@Metlosek3d Do Čech a okolních zemí jsem schopen dodat Zásilkovnou ;-) Napiš mi na: [e-mail]

[@duartefigueira1304]

I couldn't remove the pulley stock please help me

[@MotorFlash7]

@duartefigueira1304 do it like in the video ;-)

[@duartefigueira1304]

​@@MotorFlash7I did the same as the video but my polley seems to be fixed Help I'm from Portugal I don't understand your comments unfortunately

[@MotorFlash7]

@duartefigueira1304 The video has subtitles that you can watch in your own language. To remove the pulley you need to cut it and to apply it you need to heat the pulley a lot...

[@duartefigueira1304]

There are only subtitles in Czech and I'm Portuguese, I've already ruined 2 bags and I couldn't get the polley out, maybe I'll call a mechanic

[@MotorFlash7]

@duartefigueira1304 Yes, but you can switch from your language... Send photo to Email: [e-mail]

[@filidriza5517]

Do you need a new belt with it ?

[@MotorFlash7]

@filidriza5517 No

[@luci_bavariamotors9466]

Where can i buy the kit?

[@MotorFlash7]

@luci_bavariamotors9466 Where are you from?

[@luci_bavariamotors9466]

@@MotorFlash7i m from Romania

[@MotorFlash7]

@luci_bavariamotors9466 Czechia, Write to me at: [e-mail]

[@hubertszymanski2272]

Does it work for 230 kompressor? (192hp, also 1.8) - C klass sportcoupe

[@Nanoudemon]

You Already have a 65mm stock pulley on 230 kompressor 1.8 192ch but you still can upgrade it for this 62mm pulley + upgrade bigger crank pulley and smaller water pump pulley

[@vladimirart758]

Can you tell me for my slk 200 r171 (163hp) what to buy ?? Please

[@MotorFlash7]

@vladimirart758 Yes this pulley is suitable for you. Email me at: [e-mail] I have them for sale...

[@zzo28]

To je asi totozny kompresor ako 1.6L..? Nasiel som tu kladku (62mm) za cca 130eur. Drzi to tam aj casom bez problemov? Z toho mam obavu. Olej v kompresore menim ale s vacsimi otackami na to treba dbat urcite. Len to chce este vyladit k tomu ecu. Posun krutiaceho momentu nadol je dost citelny? Musi to ist aj s toi saharou, mozno kratsi stahovak.. ale odradza ma to vyberanie povodnej kladky. Nejake riziko poskodenia kompresora tam asi je 🤔 a pilit tam s flexou...uff.

[@MotorFlash7]

@zzo28 Tato kladka je určena na motory M271 s kompressorem M65. Drží to dobře na místě o to nemusíš mít strach. Tento systém stahování je spolehlivý. Jak říkáš stačí měnit olej a ani po navýšení otáček se není čeho obávat. Ano krouťák je opravdu citelný. Není to jen úprava na oko. No vyzkoušej sám. Já jsem to bez pomoci flexy nedal dolu. Jestli se ti to povede, tak napiš své zkušenosti pro ostatní ;-)

[@zzo28]

@@MotorFlash7 no prave toho vyberania povodnej remenice sa hodne obavam. Takze netusim ci sa do toho niekedy vyhecujem. Idealne mozno to zkomplikovat a vybrat von cely kompresor a vytahovat remenicu v klude na vytiahnutom kompresore. Laka ma hlavne ten krutak a jeho posun na nizsie otacky. Spolu s upravou ecu by to bol potom skvely motor a skvele auto.

[@dispatcher9052]

Woher bekommt man das Tool ?