Flashing DQ 200 DSG7 Mechatronic Unit with Odis Engineering

[@nmagsdai]

Thanks, Gigi, Nicolas from Colombia here!

[@fazbari8088]

Excellent video Gigi Bela , thanks for posting been following your uploads has helped me alot

[@LAW-fv6ys]

Hello gigi, I'm goign to buy vas6154a and flash my sport differential awd module as I have a check sum error since battery dead issue. Where do I get the correct flash files from please? Thank you for your videos, I've been watching your dsg repairs for year.

[@mastero3656]

THANKS A MILLION...... worked liked a charm :)

[@EXOVCDS]

Nice setup... you make it look simple. Flashing can be very unnerving! I've been thinking about getting ODIS from a couple of sites that I have been keeping my eyes on. Are all versions created equal? Or are some versions better than the other (like the interface you referred to). Have a good weekend Gigi!

[@GigiBeleaDK]

Drop me an e-mail and I will upload it somewhere for you :) both Engineering and Service.

[@olegolshvartsman124]

Hello .Thanks for very help video

[@ok2628]

can you help me which flash file its for 0CW 300 044N

[@lmainformatica]

Good night, great video, could you provide the electrical schematic of the connection? I have a control unit and I need to do exactly this procedure, but I'm still learning about reflash, I have a broken unit from a client and I need to move to another unit, in addition, I need to know if I save the file on the other one later, it will work. normal exchange, if you can help me i will be immensely grateful? Thanks.

[@ameerbardien7623]

Can i code a k plate to a d plate with this software?

[@jeppoification]

Can you read and save your mechatronics software??? So then you can flash a replacement mechatronic with your previous software?

[@apsyyy7]

Thanks for your Nice video . How to make reflash for the dq200_g2 using odis engineer. Thanks

[@guillaumepremat8668]

Hello , Small question when I want to flash my Mecatronic after computer replacement I use odis eng When I but login credentials When I go to flash I will have the file that corresponds to the car? Thanks in advance William

[@mateuszdrab1021]

Hi, thanks for the video. If I have sgo file for my dq200 with modified shift points, do I need to do the same setup as you? Or is it possible to flash the module using ODIS-E via OBD in the car?

[@GigiBeleaDK]

Possible to flash via OBD in the car.

[@TheDayWalker78]

Hello, how can I assign the Flash file correctly. Since the flash file is described differently, for example like an engine control unit. Greetings Daniel

[@iqbal1618]

can yo u assist me flashing other modules do you have any professional service?

[@monstargarage3432]

great video!! very helpful, mate.

[@yilmazotoboya]

hello, i have a problem can you help me? I have two LED headlight control units. One of these control units is working properly but the other is not working full function. Is it possible for me to read and save the data of the properly functioning controller and then upload it to the non-working unit? How do I do this reading from ODIS and turn it into a flash file?

[@GigiBeleaDK]

you can not READ the flash with ODIS. Find the correct software for it and flash it or go to the dealer and ask them to flash it :)

[@RadTeir]

hello my mate , would you plz tell me how can i learn about ecu programming flashing ... ? is there any course or book or anything ?? also what tools(adapters) i need to read ecu on bench ? thanks a lot

[@fifthcylinder]

Gigi, maybe you can tell me why when trying to flash 2018 sw in my 2019 RS3, it fails (version control is off). They are the same generation and tcm

[@GigiBeleaDK]

Write me an e- mail and we can discuss there. You can find my contact details in the video description.

[@sabrinatjoen-a-choy2425]

Hi my friend nice video. Question im trying to recover old software from dq200 but failing everytime u have any other solution? Mechatronic stop working on polo 2017

[@marekjuricek]

Hi, can you help me how can I program brand new mechatronics? Or read old one and send it to brand new one without passthrough?

[@jeppoification]

Hi Gigi, I'm about to buy a gearbox basically for its mechatronic unit for a dq500. I have odis and a 5054 connector but i am worried about some of your comments below. Is there a place I can search for my software version and download the flash file? Alternatively what is the easiest and cheapest way to get the flash file? Also I assume you can do this while the unit is installed in the car and not on a bench???

[@GigiBeleaDK]

Depending on the age of the car , the TCU might have immobilizer incorporated on it. If it has then no way to just swap. If no immobilizer then you can swap and if the gearbox has the same code you can swap plug and play , if not you will need to flash correct software on it , else will not work.

[@jeppoification]

@@GigiBeleaDK its a 2013 built tiguan, I can get the same code gearbox

[@GigiBeleaDK]

@@jeppoification Some DQ500 have immobilizer some not, I can not say just from the year model.

[@noext7001]

does it work with a Mechatronic with immo on ?

[@nalinperera5754]

Hello bro i want to know something. I also have odis e 8.1.3. But when i flashing can not select sgo file. What should i do for update odis e to use sgo files.

[@fiskmasen8599]

Hey nice video! I've thinked about doing this? What software and hardware are you using? If so where can I find them? Sorry for a lot of questions. Would appriciate If you responded! :)

[@GigiBeleaDK]

"What software and hardware are you using?" ???? I am usin Odis Engineering as the video says and VAS head.

[@andriusskaudzius2424]

What version of Odis are you using? I try with 9.2.2 always error. VCP and Kess works well on same Tcu?

[@GigiBeleaDK]

You need to select the correct platform else you will get error because ODS might try K-Line first or CAN and the unit might use the other protocols for flashing. VCP and Kess should work as well as ODIS.

[@hiltonjesusdesouza6601]

hello dear mate, congratulations, excellent video, do you knew say me if can flash steering assistence AUDI A4 2013? where get file to new flash?

[@butbut948]

nice job!! i used to be programming through online ,if i want yo flash it by local file, where can i get this file??

[@xxlevis12able]

Hello i need to flash frf file for ecu via obd vas5054a do i need to change any settings?

[@moomo96]

hey nice video tho, can I use this method to un brick a dq250 cxx

[@jaxelos8052]

Yes.

[@Xandao44racing]

Boa noite, ótimo vídeo, poderia disponibilizar o esquema elétrico da ligação? Estou com uma unidade de controle e preciso fazer exatamente esse procedimento, mas estou ainda aprendendo sobre reflash, estou com uma unidade de um cliente quebrada e preciso passar pra outra unidade, além disso, preciso saber se depois gravo o arquivo no outro irá funcionar o câmbio normal, se puder me ajudar ficarei imensamente grato

[@jaxelos8052]

English please , don't have translation integrated in browser.

[@imaginariamente12]

Thanks for sharing,really its nice job. recently i installed a 5.0.14 ODIS version,and it works whith my vxdiag nano in diagnostic. have you tried perform a reflash with a passthru interface?, i need to get a vas 5054 necesaraly or not ?

[@GigiBeleaDK]

Did not tried with the nano interface, but you can always try and see if it works.

[@chrispad100]

Hello sir , good video have any video to clone , copy and flashing 0am 927769G, UDS OCW TCM ? Regards and waiting for your news

[@IsmaelAbdelHadi]

Thanks for the great vid Can odis engineer flash all DSG by obd ? I saw u do it on bench .

[@GigiBeleaDK]

Yes, all tools can flash via OBD.

[@cmsea280]

Nice video. Same setting applied flashing thru OBD port? Where can I check or download the Flash file for 0am300050q?

[@GigiBeleaDK]

It's right there in the description :) For Flash Files : www.dsgfiles.com/

[@NBHAuto]

Does this control unit flash need to have online log in? And why actually do we need to flash control unit, what is the purpose?

[@GigiBeleaDK]

Just to flash units you do not need an online connection. Sometimes units fail, then you need to replace it , and it might come with wrong software for your car , therefore you need to flash with correct software for your gearbox.

[@NBHAuto]

@@GigiBeleaDK thankyou verymuch. Appreciate it

[@a.g.ttransmissaoautomatica9750]

Hi There I ve a doubt to flash dq200 in the bench, i ve tried but there is no comunication with it, i did everything as you said in your video. Thanks

[@GigiBeleaDK]

Make sure you have 120ohm resistor between CAN wires on bench. Also K Line needs to be connected to the TCU aswell.

[@a.g.ttransmissaoautomatica9750]

@@GigiBeleaDK thank you for the advice, now its working, but I have a 0am300060e and when it starts flashing it gets a tcm fault just after askes to turn off the ingnition. Just one more thing, I ve noticed that in your odis it has been written on the up right screen terminal 30, and mine it s terminal 15, could it be a problem? Thanks

[@adylol162005]

A.G.T transmissão automática same here. I get error as soon as i select to start flashing

[@charmand79]

Hi, are you using an original VAS5054 head? Because clones never work for flashing. At least none that I have tried so far.

[@GigiBeleaDK]

It's a clone unit and they all work good if you have the right driver.

[@charmand79]

@@GigiBeleaDK Thanks for the answer. Where did you get the flash files? The erwin flash file downloads dont seem to have the mechatronics firmware.

[@GigiBeleaDK]

@@charmand79 For Flash Files : www.dsgfiles.com/

[@fetoraka]

Hi friend, this method (flashing)can be used for unlocking an used tcm when inmovilizar is active ?

[@GigiBeleaDK]

No, immo is on eeprom.

[@raedkaram9465]

How many pin in this DSG connector?

[@szymonvr]

Hi. Thak's for good tutorial. But i have a question can I flash to another software number on bench but 0CW immobilized unit?

[@GigiBeleaDK]

only if you have a full read including bootloader.

[@szymonvr]

@@GigiBeleaDK so only cloning? Old unit is not available. Can I do the same that You made on this movie with 0AM...769E?

[@GigiBeleaDK]

@@szymonvr if you do it with ODIS then yes, like here would work.

[@szymonvr]

@@GigiBeleaDK it became that I should use 769K TCU unit. Got some problem when trying to flash unit on bench getting immon ON error. Can 769K unit be flashed on bench or only in car?

[@GigiBeleaDK]

@@szymonvr As I said , bench mode only if you have full read , else in the car AFTER you match immobilizer.

[@MahmoudAhmed-xh8np]

can you help me how can i bring local flash file

[@drmamarris]

Buen día disculpe yo me encuentro en la CDMX en MÉXICO quisiera comprar un equipo como el que muestran en el vídeo para hacer esos trabajos en mi país que costó tiene y dónde lo puedo adquirir con todo y calibraciones por su atención muchas gracias ATTE. Juan Bruno García Ribera

[@mefiuss]

Hello, I want to flash/update my dsg dq200 in Seat Leon, actually I've got firmware version 4510, is it worth to do that? And where I can get flashing files? I've asked main dealer to update for me even I need to pay but they say that they doing this only when the car is under warranty. Please any help. Thank you

[@GigiBeleaDK]

Why flash the gearbox ? Do you have any problems or why ? If it is not broken , don't fix it.

[@mefiuss]

@@GigiBeleaDK Last year I've changed clutch and dual mass flywheel because was little slipping, and week ago gearbox was rebuilt because of lost the hydraulic pressure. Now working fine but sometimes not so often I feel clutch slightly slip. That's the reason why I wonder to flash/update software.

[@kinhung]

Do I need to unlock or remove protection after flashing DSG on car?

[@GigiBeleaDK]

For 0AM no, for 0CW yes. 0CW can only be flashed on the car or if virgin.

[@kinhung]

@@GigiBeleaDK I have a renewed 0CW with poor power, low rpm change gear problem. I want to flash a new firmware to fix this. Wonder if it will locked the 0CW again.

[@karadiaessa]

Please can you show how to flash the AUDI electric steering control module

[@GigiBeleaDK]

Which one , for what problem ?

[@karadiaessa]

@@GigiBeleaDK audi A4/A6

[@beldonnyvanette5541]

Do you know how to save the old file,before proceed with flashing

[@GigiBeleaDK]

@@karadiaessa :D wondering why you need that ? ... it is known issue and easy and simple fix. At the next occasion I will make it.

[@GigiBeleaDK]

@@beldonnyvanette5541 Not possible with ODIS, you need other tools that can read the unit.

[@muqimkhan623]

I want to know one thing where I get the files to flash??

[@GigiBeleaDK]

www.dsgfiles.com

[@danieledamiani2250]

I understand that flashing means copying/cloning old unit information to the new one. What kind of information? I bought a refurbished unit from China and seller told first that he is going to programm it to my vin number but after sending has told that I need to make "adaption" with 5054 tool and odis software. Is this correct or is he just lying to me having done nothing about programming? Thanks.

[@GigiBeleaDK]

If unit is flashed with correct software then you are ok, just need to make basic settings on the car.

[@kinhung]

@@GigiBeleaDK basic setting need security code or not?

[@GigiBeleaDK]

Nope.

[@jebasun02]

GigiBelea aka JAX hey my 2006 GTI randomly won't shift in reverse and won't go out of first gear. I took it to a shop and had fluid replaced/refilled but the transmission still randomly stops working. The car will drive fine sometimes then revert to being broke. I found a code on the car that is P0608 and P2732. Do you think it's just the solenoid broken or the mechatronic ecu itself? My PRNDS is flashing on my dash as well. If it's just the solenoid I was going to try and have the shop replace them

[@sinuesegura2831]

I have error ODS8011E please help me..

[@PedroGonzalez-yr6xd]

Hi, I'm from Mexico. Could you please help me with a reprogramming by team Viewer?

[@GigiBeleaDK]

Sorry, I have no time to teach via Teamviewer :(

[@polo16v191]

Hello, thanks for the video. A question, where to find the files for our mechatronic?

[@GigiBeleaDK]

www.dsgfiles.com/

[@vovanidzevavasik4944]

Hi! Good video/ But can you give a wiring diagram of connection? Thanks.

[@GigiBeleaDK]

Google for DSG7 pinout :)

[@alasadi1974]

hi I NEED J2534 DRIVER FOR VAS 5054 IF YOU HAVE IT PLS. SEND IT TO ME

[@drmamarris]

Good day sorry I am at the CDMX in MEXICO I would like to buy a team like the one shown in the video to do those jobs in my country that cost has and where I can buy it with everything and calibrations for your attention thank you very much ATTE. Juan Bruno García Rivera

[@jaxelos8052]

Contact me by mail.

[@andriusskaudzius2424]

Can this be done to all dsg units? I cant flash dsg 6

[@GigiBeleaDK]

Yes , would work on all DSG6.

[@andriusskaudzius2424]

@@GigiBeleaDK I'm trying to clone tcu with diff. Hw. But no go. File size is diff. I need to flash file 705kb, but tcu except only 417kb file.

[@GigiBeleaDK]

@@andriusskaudzius2424 LOL , that will never work , different hw is different CPU architecture. You can only make clone ONE to ONE on same HW.

[@majidyasin2386]

Hi. With odis E. Can u flash to older software?

[@GigiBeleaDK]

yes, no problem.

[@majidyasin2386]

@@GigiBeleaDK i tried and it refuses. Can i ask how?

[@GigiBeleaDK]

@@majidyasin2386 What hardware you have and what software you wanna flash ?

[@majidyasin2386]

@@GigiBeleaDK odis e 12 with vas and the gateway want to flash it downgrade. But i hear cnt upload fecs after.

[@GigiBeleaDK]

@@majidyasin2386 "But i hear cnt upload fecs after" ... I do not understand what you mean ...

[@yunus148]

Thanks for the video. But please remove or block somehow the telephone number of technical service in Wolfsburg.

[@jaxelos8052]

Why ? ODIS works just fine with a trial license :)

[@arascho4163]

can i dump my old mechatronic and transfer it to the new one?

[@GigiBeleaDK]

Yes, if it is the same hardware number. But you can not read with ODIS, you need another tool that can read.

[@arascho4163]

GigiBelea aka JAX Which tool can i use?

[@GigiBeleaDK]

Vag Can Pro

[@arascho4163]

GigiBelea aka JAX Do you mean "Vag-com-diagnostic-system"?

[@GigiBeleaDK]

No, I mean Vag ,Can Pro. vcp-system.com/

[@ousmanesarr7287]

Hi how do you get the flash files thought?

[@GigiBeleaDK]

I have built personal database.

[@ousmanesarr7287]

@@GigiBeleaDK okay. can you help me ? i have a list of flash file of this style: 0AY907554H_0044.sgo. my problem is how do i identify wich file is for what module. and how do i link the file to odis enginnering? am new to odis word and trying to learn. thank you

[@andreirobaciu8179]

Salut, cum pot lua legătura cu tine?

[@jaxelos8052]

Contact Details : www.evosoft.dk/tech.html

[@hjlautoparts2555]

Dear friend, We’re looking for the repair shop partner who can help our clients to install the 0AM DSG 7 transmission control module. If it’s ok for us to recommend our customer to contact with you, kindly email me: candy.lai@hjlautoparts for further discussion. We’ll recommend car drivers to contact with you for their car fixing. Many thanks in advance, Candy HJL Autoparts

[@aminameen3107]

hi can you flash s-tronic audi ? can i get your number? living in malmö