Flat roofing installers London,Torch on high performance licensed installer Aldersbrook

a brief video of a high performance cap sheet being installed correctly on a flat roof by Danny of Aldersbrook Roofing Flat roofing installers www.aldersbrookroofs.com

[@clivebyrne2297]

What a cowboy I’ve never seen anything like it

[@user-1980_fahad]

المشكلة دائماً بالانسان والحيوانات ليس لها علاقة

[@whatyousaidbud]

For anyone criticising, this is how work quality evolves when customers always choose the cheapest quote.

[@ajelicits3435]

use a metal puller and preheat the laps a little ahead of time if you want a bleed. dont walk or knell on your rolls, stan behind the roll and pullit towards you. If you work fast the rolls you are currently kneeling on would be far too hot still and would leave marks. Maybe it doesnt because you only heat the laps which is incorrect.

[@alexgreig3598]

Must have asbestos hands and tough knees kneeling on that mineral!

[@blizzardxc12]

Bet that guy burns himself so many times a day At one stage i thought he was never going to move the gas hose

[@jolles8798]

I would get fired if my boss saw me torching like that. Geez that's terrible. He doesn't even cut corners when he overlaps!

[@tinkletoesrus]

whats this mean mate im learning to do this. pitched roofer by trade

[@bumblaster9000]

@@tinkletoesrus you cut the corner of the black off at the end of each run

[@ajelicits3435]

@@tinkletoesrus watch soprema training course of flat roofing torch on if you wnat to learn the proper way.

[@robert_costello]

I swear, you would’ve been fired 30 seconds into this video. That’s a 400,000 BTU torch and you decided to go with your bare hand?

[@ajelicits3435]

the bare hands part is not even the issue here, it's literally everything else hes doing including wearring shorts. Ive roofed over ten years and rarely use gloves when torching, a small burn on the hand is nothing, open shorts on the other hand is insane. if hot tar splashes your legs i feel sorry for you. also the way he torched the roll was all wrong.

[@leoanazemi3797]

He is proud to show his master work lol

[@deancutajar7858]

Don't worry about cut corners underlay would be a good start

[@shariefadolley2156]

How do I get I touch withu

[@lutonbusdriver2315]

Geez! Get yourself a trowel, long pants, pair of gloves and a longer hose. Feel for the people paying for this work.

[@boyo57]

And a decent stand so he can put the torch down....beggers belief😁

[@davidgray5252]

You sure, ! what you warming up a lap in the underlay for ?????

[@dalvid26]

That looked like hard work jesus

[@eugeneeugene8252]

That joint is going to blow bubbles

[@warmachine576]

I cant believe they posted this to advertise the company lol a fart could rip that up

[@sukhdevhayer4992]

Shocking felting!

[@kevinyardley7193]

No roll bar, cant control the spread of bitumen across the roll, it must all be fully adhered

[@lesliegibson]

Gloves???

[@makingbreadnotcrumbs]

i hope he isn’t a foreman cause honestly I’m concerned for his crews safety.

[@michaelwoodward780]

The London way ey , that mineral looks nasty reminds me off a ciggy paper

[@graemepae100]

History states that he is still torching this on in 2025 😂

[@ajelicits3435]

hahahhahaah

[@callumgoodall7272]

That ain't stuck where did they find this fella 🤔

[@ajelicits3435]

ok, you also have to cut a 45% angle on your pieces you are going to connect onto each other. it allows the entore rolls to stay one size instead of doubling it up and created high spots. he's also wearing shorts, wtf???? he's not getting any rrof down the way hes doing it, his knees would literally burn if he was kneeling on a freshly torched piece or even on a very hot day the cap gets so hot even with clothes its too hot to kneel on.

[@ajelicits3435]

this is what you call a lap torcher. you have to heat the entire roll. I could get the right angle and ppull that up not long after you torch it down. if properly torched you cant.

[@JuanElBautista89]

Kneepads, gloves, safety glasses, long sleve shirt, pants and a fire extinguisher

[@carlglover3547]

not a clue

[@ingmarboots9700]

Howdy ho partner!! Wodkaroofer for live!!

[@adamgordon2091]

Ever heard of pulling your roll with a cane?This is why people percieve roofers as idiots!

[@tylesveque2373]

Spot welding lol I think it's time for me to post videos

[@lostsoulatl]

His fingers are crying out for more

[@alanredmond6646]

No gloves wearing shorts maybe high performance felt not labour

[@davidgray5252]

Of all the crap felters I have seen on here I think you are sitting round about No 6 !

[@tristanedwards1340]

He didn’t even win that

[@davidgray5252]

6 thats generous

[@elmermunoz79]

Cuanto por squares

[@RaulPalma-jc5er]

you have no idea to install asphalt sheet. The first thing you have to do is put on some gloves and suitable clothes. and the second is to move the hose aside so that it does not burn.

[@windsorroofingsolutions]

Wy ant he rolling it out with his foot wat a fucking joke.id put a 100 meters down by the time he had layer a 8 meter roll

[@leeandsarahsworld8091]

Fully licensed in doing it the wrong way 😂

[@johnboy542]

Should be called john wayne roofing london

[@jamiehalstead9058]

There's no way u got a licence for that torch 🤣🤣🤣

[@andreamelardi6196]

ma cosa stai facendo?

[@asroofingservices]

How do they get away with this work and better still get paid for it, beats me!

[@hectorvillanueva2464]

Necesitas 👢 y guantes

[@lupe4980]

You should be ashamed, thinking you where going to get away without anybody roasting you 😂

[@travissmith3720]

Good job. Most roofers do slop jobs. But it would be easier if you had gloves , a bar , and knee pads

[@Ser_Yozha]

Это плохая работа. Он вообще не умеет работать.

[@ryanlockwood157]

Why is he using a scraper for the lap underneath 😅 what ever happened to using a roll bar? I'd have done 3 jobs by time he completed that run

[@davidclark2422]

Lmaooooo from Canada. Get a pull cane rookie

[@whoville90]

Hknestly... i think herr in Canada we have better torchers ive seen so mNy vids from other countries and damn horrible work

[@johnmason9544]

This geezer winding me up

[@davidclark2422]

By the way good roofers cut corners. Ifree game for ya

[@jordanhudson5605]

Haven’t got a clue 🤪🤪🤪

[@jcoleburt]

I think a glove would have made life a lot better.

[@dannyrodrigues3226]

asbestos hands are always good

[@richardgardner8503]

And knee pads

[@Chris-jl6vk]

And a foot

[@Chris-jl6vk]

Pro's don't need gloves

[@rubenaranda2672]

What is this ? Your fired on my book.

[@grantkincaid7820]

I’m a flat roofer and honestly, Iv never seen anything like it. No gloves. No constant flow of heat, crap bleed. Sorry but that won’t last 5 minutes. If you stuck your underlay properly then you wouldn’t have had to stick the lap Jheeez 🤢🤢

[@olej2183]

Because he most likely use a sbs type and not a app thats why.

[@PERKINS4107]

I find it very hard to abide by KZbin's mantra of keeping comments respectful etc etc when you see work as fucking shit as this!!!

[@ivcarrasquillo2488]

Move the tank.. Dann near burned the hose

[@mikerim6861]

Where’s the pressure to ensure no air is trapped?? Any trapped air will form into a blister when warmer weather arrives. Might look flat now but wait for hot weather 😰

[@wallywally3738]

How would you apply pressure?

[@mikerim6861]

@@wallywally3738 Roll the felt up tight and get on ya feet behind it, roll it out with pressure from your foot, thus forcing air out. Science says air expands with heat so trapped air forms blisters. That guy on the video isn’t a roofer, he’s painful to watch

[@mjh5437]

@@wallywally3738 Have someone following behind with a heavy roller while its still molten soft.

[@pidge30]

Cowboy 💯! Shorts & no gloves 🧤 😂🤣

[@CentralNicon]

He doesnt have e to shave his knees anymore

[@ariojalilzadeh3821]

Shorts!?

[@axelvideo]

No gloves, tar all over the gas hose, and why even bother with the Hi-Vis?

[@MdYeasinArafat-ob4nv]

I dont that's work

[@Jason3249...]

Holding the blowtorch wrong, the technique is completely wrong 😂😂😂

[@olej2183]

It doesn't matter what technique you use 🤣 the end result it was matters. If the technique works for him then it's not wrong 🤣

[@rc3171]

Your having a laugh defo your first job

[@user-1980_fahad]

لم يتخذ اي شي من ادوات السلامة. والجودة

[@kevincasson9848]

No gloves, he's burnt hosing tube. He should be rolling with feet. He's too slow felt not sticking properly He's a cowboy make no mistake!!@

[@alextanase6809]

Man it's gone burn his fingers 😅

[@jonasmagnusson2099]

You can’t work as a roofer without gloves!

[@RicardoRivera-eg4eu]

Chi gon primo asies

[@dannyb4094]

Lol!!

[@roryb3013]

What the fuck is he doing 😂😂😂

[@daveedwards3658]

What the fuck is he doing ?

[@williammcgeehan3424]

😳😳😳😳😳😳😳😳😳😳 Good grief !!!!!!!!!!

[@Naedanger253]

That's not how you do it 😂

[@keithduncan9304]

What a grade 1 mug for doing this without gloves, knee pads, and worse of all how close was he to the gas line ??? People like him need to get an office job, accident waiting to happen. Yeah lets do a YT vid to advertise who we are and what we do !!! CSCS card? Yeah right """

[@hectorvillanueva2464]

Mala técnica

[@MrFlatroofer]

Not my way of roofing.

[@snowreal8871]

😁😁😁😁😁😜😜 Superrr

[@paulmecock1]

Wow I’m not mr health and safety but he is a accident waiting to happen

[@mjh5437]

What a total div,he hasn`t got a clue,that won`t last 20 months,never mind 20 years.

[@kieronsimpson777]

Omg

[@nelgchannel9661]

lol

[@a1motorcycletrainingandsal528]

Joker

[@bartoszm6325]

This was painful to watch.

[@dw4525]

Comedian

[@borisjohnson2498]

Amateur

[@kevincasson9848]

Cowboy!!!

[@kaliefazz5952]

😂😂😂😂💩💩

[@antonfarqua]

69 likes🤣🤣😅

[@martinjvillasenor773]

Totally amateur!! Why post this?

[@projektredduck4592]

Trrrrrrasssshhhh no even heat, no cut corners, no cane, no trowel, no gloves, wearing shorts, propane tank to far or not enough hose..... fiiiiiiiiiired... wonder if he even has a propane ticket to even connect anything to a propane cylinder lololol.....

[@AliGspot]

Haha it is terrible work. Wondering what you mean by cut corners? Do you do this on the straights across the deck?

[@projektredduck4592]

@@AliGspot Anywhere there's an overlap even for wall flashings...Don't want any peeled up corners, do it for TPO, PVC and burmastic. Your boss will thank you later for saving him money and time. Unless he's a cheap asshole then. By all means do what you want lol.

[@projektredduck4592]

Also noticed he didn't butter up that end lap, don't be like that clown. Better yet don't follow this company or use their video as any form of learning tool. Lol 😂

[@AliGspot]

@@projektredduck4592 great advice, thanks mate

[@oskar8603]

Slow and sloppy

[@johnmuir8930]

Cowboy

[@ivogrinvalds8698]

So bad work

[@whoville90]

Lmfao this is horrible bro wtf r u doing use a dman cane honestly I think the best torchers are here in Canada... I mean I've been doing this work for 8 years only .. no lie, my work is impeccable... I'm already at 42.50... and hopefully soon get to run crew :) and imnjust 30

[@alistairlaird3883]

Cowboy