✅ Floating Shelf 🦾 How to make strong plasterboard shelf 👉 drywall

✅ How to INSTALL Gyplyner UNIVERSAL Ceiling Lining 👉 Drywall Metal Stud
• ✅ How to INSTALL Gyply...
In this video I will show you how to fix the profiles for plasterboard on the wall so that our shelf is resistant. You will also see that, when putting the plasterboard plates to our structure, it is convenient to screw throughout the entire structure for greater resistance.
▶︎ fischer SX plug
Characteristic:
- 4-way expansion ensures maximum grip.
- The shock penetration lock prevents premature expansion of the plug during its introduction.
- The rim prevents the plug from slipping through the hole.
- Resistant to temperatures from -40° to +80°C.
- Anti-rotation fin in outer position to prevent rotation even in the most hollow materials.
- The expansion-free neck prevents damage to tiling and plaster.
Video transcript:
Very good!
Today we are going to see how we should fix this shelf so that it supports heavy weights.
We grab our tools and get to work.
We mark the level at which we are going to mount the shelf.
I am going to make a shelf of 73cm by 27cm.
We cut a channel at 120cm. Now we mark 25cm at one end and at the other.
We make some cuts in the marks to be able to bend the channel there.
We place the channel on the laser line and drill in the middle so that it stays on.
We are going to drill just on the two edges of the channel. That will make our shelf strong.
Now we screw. We must use good plastic plugs.
We cut some pieces of upright to reinforce in the center.
Cut the front channel and place it.
Thanks for your support.
If you like my content and you are not yet subscribed, what are you waiting for?
We check that it is well level.
If it is necessary to readjust the level in the front part, we can do it by inserting some wedges behind the channel that was screwed to the wall.
We put the sides square and fix them.
We check that it is the same size on both sides and fix the profile.
We take out a measure to cut the plasterboard.
Let's go with the placement of the plates.
We screw both into the channel and into the stud. That will give you even more resistance.
We can screw right where the stud intersects with the channel.
We measure the width of the edge to cut some strips of plasterboard.
We put it on and screw it on.
With a handsaw we cut off the excess.
Now we put the ones on the sides.
List our shelf. It would only be pasted.

[@TheMadManofDRYWALL]

In this video I will show you how to fix the profiles for plasterboard on the wall so that our shelf is resistant. You will also see that, when putting the plasterboard plates to our structure, it is convenient to screw throughout the entire structure for greater resistance.

[@818Rico]

AWESOME VIDEO 💪 Thank you for the knowledge

[@paata110]

Good job👍👍👍

[@eb5ua]

Gracias

[@FRESHDON.]

Nice

[@Trambulhao]

¿Los tornillos de la pared son los mismos que los de las tablas?

[@mais1reparos680]

Sensacional kkk

[@obito7190]

How difference between black screw and clipper to joiont it?

[@nikolad5754]

You just put regular profiles in video and thise hold your weight? Its not possible, you destroyed this and made it in different way and than filmed your hanging.

[@dennisbang963]

Ich bin der Meinung das es halten kann, aber auch nur 2-3 mal, denn danach hast du die Dübel aus der Wand gezogen und die halten nichts mehr

[@didiershouck5548]

👍

[@IndryanLongkutoy]

Luar biasa 👍👍

[@servanhemdiyeli9736]

Salam qaqaw

[@thezombiecs1.6umbrellaswar12]

как се казва този иструмент

[@georgeleo76]

Nevěřím že to bude pořád takhle pevné. Já osobně bych v místě profilu navrtal dvě velké díry a na chemickou kotvu bych dal asi 1" ocelové trubky.

[@polmaclin3019]

THIS IS A JOKE, THE SHELF WILL FALL TOGETHER WITH THE PARTITION WALL

[@Eng.KhaledGamal]

🤔🙄

[@greenapplepromotions]

I think I’m in ❤ with you😍

[@ej558]

Fake I’m a metal stud contractor and that’s 25 gauge metal with crimp punch connectors…. The metal would tear at the screws into the wall…. Nice try though