Straight pipes were just too tremendously loud. Had to add on this muffler.
Пікірлер: 104
@guitargod662 жыл бұрын
I enjoy all the fuckfaces commenting about the welding that have probably never touched a welder and never will ♥️ Clearly with all of the scrap exhaust with weld beads laying around, I was still learning, and still am. This welder is a shitty Eastwood China welder, I was butt welding, not using the right wire, and not doing anything the “right” way. You can’t “run a bead” on anything that I was doing. It held as long as I needed it to, and I later on welded an entire turbo log manifold together that’s still holding 9k miles later. To everyone else who’s dead grandpa that didn’t raise their kids and grandkids to be cunts to strangers on the internet, thanks for the views and comments.
@dylanthompson6427 Жыл бұрын
Well I weld for a living. And that was hard to watch. Cringey
@guitargod66 Жыл бұрын
@@dylanthompson6427 awesome!!!!!
@Chit_126 Жыл бұрын
😂😂😂😂😂
@simonhardgrave4568 Жыл бұрын
Fuck the haters man welding is all about practice 2 years ago I couldn't weld half as good as you. Now I tig for a living. Practice is the only way love the work brochachi
@richiesspeedshop82 Жыл бұрын
Welp as long as there's no leaks who cares. No one's going to look underneath and say LOoK aT The wElD jOb gUyS. Unless you bring it to jiffy lube lmao
@Occuria13 жыл бұрын
My grand dad was a welder, he just turned in his grave watching you weld. Set your heat and feed speed correctly and lay a bead down.
@jaymaro-jay43073 жыл бұрын
Lmfao dead 💀
@Yophillips32722 жыл бұрын
I think this was more of a fitment issue, you shouldn't really just butt up exhaust pipe like this, expand the pipe or get an exhaust fitting so the pipes fit together and overlap so you can actually weld it clean.
@wildestcowboy26682 жыл бұрын
Andy I'm glad you told that Joe Biden loving gun banning clown off. He a welder like I'm a G.....
@LSX_GORILLA7 ай бұрын
😂
@LookAtMe-C1373 жыл бұрын
You just helped me make up my mind. Flow FX is going on my ride. Thanks!
@maxwolthuis4 жыл бұрын
Never underestimate a man in his garage... with a sawzall
@guitargod664 жыл бұрын
Talredhedkid lmao!
@JoanWilder19852 жыл бұрын
Ha ha your commentary is awesome! Don't worry about the welds as long as it works no worries. Thanks for sharing.👍
@guitargod66 Жыл бұрын
lol thanks I just act like my idiot self, glad it’s entertaining for some 😂😂
@JoanWilder1985 Жыл бұрын
Your video was more entertaining than most and gave a idea of how the mufflers sound.👍
@robertbittles69444 жыл бұрын
Excellent video. My favorite is probably the 19:58 mark though. LOL!
@ze_german29214 жыл бұрын
Sounds very Nice, I have an 86 Squarebody with a 5.3, soon to be 6.0
@guitargod664 жыл бұрын
ZE_GERMAN sounds like a whole bunch of fun. I’m about to start this thing up after installing a turbo 😳😳. I should have it started by next week
@jackmehov17963 жыл бұрын
Oh yes the old foot clamp absolutely is the best choice
@stevenfoust37823 жыл бұрын
You need to commit to the welding process and get a bead going! Also, making sure the parts actually fit together would be a plus. Other than that, good job sounds nascar.
@jasonmackow3631 Жыл бұрын
Was looking for a video on this muffler with a cam I have a 3” running straight from the turbo out the side like yours and it’s just disgusting sounding up top lol definitely putting one of these on when it gets warmer
@MobileBarberLife3 жыл бұрын
Your sarcasm made this video worth watching alone😂..came out mint even tho your welds look like Ray Charles welded them with his feet lol jk ..new subscriber truck sounds amazing, keep on keepin on🤙🏼
@coupedeville97413 жыл бұрын
That welder sounds nice my Boi 🔥👊👍
@jeffs.24312 жыл бұрын
A pipe expander from a tool rental place would have made your job easier!
@DanielJaegerFilms4 жыл бұрын
Minty 👌 19:58 😂😂😂
@Fife_Life839 ай бұрын
Why post an exhaust video and not rev it up?
@justinh50364 жыл бұрын
Sounds bad ass man
@lanceopperude58684 жыл бұрын
Hahaha.....that was the best!!! FUCK OFF PB Blaster (j/k I love you). Hey thank you for the video and the sound !
@madpainter693 жыл бұрын
sounds good thx for sharing
@72830justed2 жыл бұрын
This is killing me!
@jesusa.espino6408 Жыл бұрын
At least we know you have tool Enstien 🧐😭
@davidtaylor50825 ай бұрын
I just got some flowers Tec bullet mufflers and I hate how they sound does this muffler have the raspy crack like a glass pack muffler or do they have a deep tone like a regular muffler flowmaster has
@redeyeracing87312 жыл бұрын
this was defiantly painful to watch
@jeffs.24312 жыл бұрын
I just took a FlowFX off my truck. Too much drone for me.
@publikintox89210 ай бұрын
Dont listen to anyone who says something aboit your welds aslong as they hold they are good and atleast you are doing things yourself if you fuck it up you can try again
@lsx5.3colorado134 жыл бұрын
Can you make a video of you taking off cruising and wot I'm thinking bout getting these
@guitargod664 жыл бұрын
Keldon Alverson I definitely can. Just keep in mind that I hollowed out the cats too
@lsx5.3colorado134 жыл бұрын
I did a ls swap on my colorado headers bout to run dual if I like the next video u post
@redeyeracing87312 жыл бұрын
sounds good....
@jesusa.espino6408 Жыл бұрын
For all people back at pendeo😎🍒
@vintagespeed7 ай бұрын
bro. what are you doing with that cutoff wheel??? :D that's how they end up in your face! thanks for the vid. 👍
@guitargod667 ай бұрын
lol I take safety a bit more seriously these days
@markmccle4 жыл бұрын
U dont cut the ends of the muffler off
@mrstl3000 Жыл бұрын
Wonder why he did that muffler should had fit over exhaust pipe
@CBiskitone4 жыл бұрын
Wish I could weld period. Some skill is better than no skill. Nice video.
@StephenBrewer893 жыл бұрын
Get out there and try! You will have fun if nothing else
@mgdwj2 жыл бұрын
God I hope your not planning on using that camshaft in an engine after that
@guitargod662 жыл бұрын
That was the stock cam
@naboru10002 жыл бұрын
19:30 - new sound
@MrJbfixer4 жыл бұрын
If it was getting hard to see with your helmet, get a better helmet bud.. You're burning the F out of your eyes, not too mention heading for a nice round of flashburn!
@guitargod662 жыл бұрын
I said that while I wasn’t wearing the helmet 😀
@maxsinventions89134 жыл бұрын
What do you think this would sound like on a 4 cylinder?
@oldfart85012 жыл бұрын
Like all straight through mufflers on 4 cylinders, imagine a bus loaded with kids all fart'n at once
@maxhrb31242 жыл бұрын
@@oldfart8501 😂😂😂😂😂😂
@christopherwelsh17855 ай бұрын
I put one on my 06 RSX it sounds pretty good, and I also have em on me 92 Chevy 350
@FerRod21133 жыл бұрын
Is the drone tolerable?
@MRRANDOM1 Жыл бұрын
No I’ll be removing a 3”
@toycoma982 жыл бұрын
Whats inside the flowfx muffler? Fiberglas mats or steel wool packing?
@guitargod662 жыл бұрын
No idea
@nickdunn70034 жыл бұрын
How much louder is this muffler compared to stock?
@guitargod664 жыл бұрын
Nick Dunn with the stock y pipe, probably not louder at all.
@JesusMartinez-fw5nh3 жыл бұрын
@@guitargod66 wait so if I want my ride louder I shouldn’t go with the fx??
@MrRuss582 жыл бұрын
love the video. but you need help on that welding brother
@guitargod662 жыл бұрын
Thanks for the input. I had barely any experience and was still learning in the video. I welded an entire manifold together on this engine later on that’s still holding today 9k miles later
@MrRuss582 жыл бұрын
@@guitargod66 .. I still learning too.. I use a harbor freight welder no gas.. I did my muffler on my car.. came out pretty good..
@jeffreymoore27163 жыл бұрын
Race truck?
@oscarvillarreal89512 жыл бұрын
Does anyone know if these mufflers are legal?
@guitargod66 Жыл бұрын
My guess is that it would depend on your local noise ordinance. You can google the local statutes and there might be a decibel level of acceptable volume. I guess you’d have to take a chance and throw the muffler on then have a machine that could tell you the decibel level of your exhaust to verify if it would be within the tolerances of the law.
@oscarvillarreal8951 Жыл бұрын
@@guitargod66 thanks 👍
@oscarvillarreal8951 Жыл бұрын
@@guitargod66 oh what welding machine did you use?
@guitargod66 Жыл бұрын
@@oscarvillarreal8951 just an Eastwood 110V mig with regular mig wire
@oscarvillarreal8951 Жыл бұрын
@@guitargod66 does it use gas?
@cesaralexispresunk47472 жыл бұрын
Me gusta más la soldadura 😁😁
@W0LV1E454 жыл бұрын
How loud is this? I want to buy it but I don't want to waste my money since my current exhaust is too loud. So loud it hurts my eardrums. Asking since video usually doesn't do the noise justice.
@naailable3 жыл бұрын
I'm wondering the same haha
@guitargod662 жыл бұрын
I enjoyed it. I swapped the muffler for a turbo shortly after but it was pretty nice while I had it. I’d ditch the 90 degree bend tho
@MRRANDOM1 Жыл бұрын
Very loud, I’m bout to remove mines
@BUZDRIFT3 жыл бұрын
omfg those fkn welds! hahaha!
@guitargod663 жыл бұрын
🤷🏻♂️
@artmendes12574 жыл бұрын
You still getting drone?
@guitargod664 жыл бұрын
Arturo Mendez yep
@jjuarez19843 жыл бұрын
Can I put it on a Toyota Corolla??😂
@dosi82744 жыл бұрын
This was painful to watch
@guitargod662 жыл бұрын
It was painful to record !
@LongLiveNirvana54 жыл бұрын
Long tube headers?
@guitargod664 жыл бұрын
Tyler Lindsey all factory exhaust but I cut the cats off, punched em out with a pry bar, and welded them back to the y pipe.
@austinmoore13203 жыл бұрын
🤣🤣Fuk that cam 😅😅
@guitargod662 жыл бұрын
Stock cam 🙏
@BigTexVet4 жыл бұрын
Go buy scrap metal and practice welding. Honestly painful to watch.
@guitargod664 жыл бұрын
Devin Curtis I appreciate the feedback. Actually my neighbor has given me a bunch of scrap and I’ve been practicing quite a bit since then. Not saying I’m any good but I’ve been practicing
@zuperzleeper3 жыл бұрын
@@guitargod66 find a speed and amperage and stick to it. That shit was cringey.
@chocolatemilk9102 Жыл бұрын
i’m trying to decide between the flowmaster straight through and the magnaflow straight through… What do you think?
@guitargod66 Жыл бұрын
I don’t have experience with the magnaflow but I’d buy the Flowmaster again for sure