Flush Setting -Tools and Equipment You Need and Why You Need Them

#AtTheBench #flushsetting #stonesetting
Andrew talks you through what tools he uses when he flush sets stones. He shows you the tools and explains the reasons why he uses them. No actual setting takes place in this film, just talking I'm afraid but it is all useful information to know before you actually start setting.
Please reach out to him by what ever means you can and ask him some questions that he can make films about. It may be something simple or just a thought but please reach out to him so he can make some content for us all to keep us entertained over the next few months.
Mini Burnisher www.andrewberry.co.uk/product...
Thermo Loc www.andrewberry.co.uk/product...
/ atthebenchuk
/ at_the_bench_uk
/ andrew_berry
THE EQUIPMENT I USE TO VLOG AND FILM
Epidemic Sounds www.epidemicsound.com/referra...
Canon 80D, Body; amzn.to/2Lfkdk7
Canon Lens 10-18mm; tinyurl.com/gncnrwz
Tripod for Canon; tinyurl.com/hdhuz6z
Memory Cards; tinyurl.com/z8mhuk4
Card Reader; tinyurl.com/z97tccx
Microphone, Cheap; tinyurl.com/hbxtthg
Microphone; tinyurl.com/zpjpoeq
Canon G7X Camera; tinyurl.com/jkvu4b4
Tripod for G7X; tinyurl.com/z27m9aj
Mini Tripod; tinyurl.com/he93omu
Mavic Drone; tinyurl.com/jfh9da4
360 Camera; tinyurl.com/jbmrugq

[@miekemanders6598]

No need to apologize for the length of the tutorial. It was very instructive, all my questions has been answered. Thank you very much!

[@tammygurl64]

Hi Andrew, After a little more than 3 years of watching your tutorials, I've FINALLY decided to be brave and try flush settings. Thanks so much for all your help!🙂

[@stephencoster9532]

Hiya & thank you, I learned as a spark back in the 70's that the why is almost more important than how, at least it is in getting the right mind set, so as I say thank you & stay safe...

[@allanthompson9695]

Cant wait to have my first go at flush setting. Thanks Andrew. Excellent Tutorial.

[@raa137]

Comment: I almost always drill through. A well cut faceted stone shouldn't need light coming in from the back, although not all faceted stones are well cut. But. getting dirt on the pavillion will dull the sparkle of faceted stones. The backs of stones inevitably get dirty even in a flush setting. Having an open back facilitates cleaning the pavillion.

[@olegpetelevitch4443]

Yep 35yrs hand made jewelry !

[@mary-annkieckhaben5026]

Thank you for this Tutorial.

[@saulebu2245]

You are soooo helpful!!!

[@lynnegutterson7172]

thanks again Andrew :-)

[@gilliansprott5487]

So helpful.

[@MacherlaPrabhakar]

Thank you sir 🙏, for your for your work,

[@mohsinshuja5277]

Thanks Andrew I find your videos very helpful. Could you do a video on setting multiple stones in close proximity such as in a pendant, maybe encrusting say a cross or dog tag ?

[@MrBlaineblaine]

Next video would you please cover buffing wheels. There are so many choices. Looking at the rio grande catalog. felt wheel, yellow treated, blend, muslin, loose coarse, chamois. And then there are some that look like scotch bright pads.

[@ElinHaugan]

Had to laugh just a few seconds into the video. The automatic texting turned 'go buy some more burrs' into 'go buy some more booze' 😂

[@dylancarter6386]

I appreciate you sharing your knowledge with us! What a great gift to the artistic community. Much love!!!

[@jakkibaker1818]

Very nice video ,I am not that good at this wood the foredom hammer drill help me better as they are not cheap could you advise please

[@jyrikoskinen1198]

Thank you for very clear tutorial! What size burnisher tip do you recommend to gems sized 3-4mm?

[@Ken_Dalton]

I did my first flush setting last week after the video. Came out lovely, done a real nice bright cut around the stone then too.. I knew that part about dragging the burr over to get the holes concentric, but what Iam finding trouble with is, u know when u drill thru the piece, say on a band where the stones are equal distance apart, how do we ensure the spacing of the holes underneath are evenly spaced? 🤔 I noticed one or two were closer together even tho the top they were spaced fine, does this come with experience, or isn't is as important underneath??. This has been a Great indept series on flush setting, thank u Andrew 👌 ps, got some gravers too 😉

[@mariadesa4162]

Ken, have a look at the Diamond Mounter's video on how to drill straight - but you're right though, it will come with experience.

[@wildskud]

Thank you for your way of explaining things. You have an excellent way of covering all facets on the gem of enlightenment making it easy to understand where you're going with things. This is the closest to what I'm searching for that I've been able to find. So...... if i was making a pavé or something like that with bead setting and all that jazz, is there some kind of ratio between the stone diametre and the size of the pilot hole that I should keep or is it just a hole wide enough for the pavillion and small enough to keep the stone from falling straight through? Are there any standards that should be upheld or is it something each one defines for him/herself as time goes by?

[@cheetah6881]

Fellow stone setter told me once that general rule is: pilot hole should be ~3/4 of stone diameter. Of course sometimes if stone is poorly cut, you need to re-invent stone setting ad-hoc and all "golden advices" are useless. If your stone don't fit the set that it logically should fit, inspect the pavillion and girdle - it might be curved and the set will require more "individual approach" than usually. Hope that helps, cheers!

[@USNAV]

What type of caliper is used to also make markings in metal. Steel or veneir?

[@albertpartridge6716]

dose it not cost you a fortune in butane gas for those small torches you use? when please you are doing a prong setting what size of wire do you use please, is it better to use square wire or round wire, if you use a 2mm stone or one point five mm stone and you use a one mm wire to make the prongs and setting the stone will be obliterated and if you use to thin wire it will not last for very long, can you sort me out please as I can only afford the smaller stones up two sat three mm at a lot of saving a four mm stone thank you for your time, take care keep well keep safe.

[@dominikaszularz9740]

Does anybody know if cubic zirconia (CZ) need light from the bottom to sparkle??

[@HANDTRICKS1]

andrew i hope you can can help me solve this problem, i have a lot of scrap sterling silver and when i melt down to an ingot it becomes brittle in certain spots ,it starts to crack after hammering to flatten out a bit and i do re heat it through out the stages of hammering it flat ...any advice you can give me .

[@magorzata8213]

It probably would be a silver with some bit of solder

[@myrtille92100]

Thanks for sharing! How about the Busch new burrs Pave cut 447? Would you recommend?

[@Atthebench]

I’ve been testing these for Busch buts for over a year now. They are expensive but brilliant. I have a few that I will be producing a film on shortly

[@myrtille92100]

Thank you Andrew!

[@i.erkingocen7404]

Hey Andrew, I like all your films without any exception. I have rather a silly question. I love making jewelry, especially rings for myself unprofessionally of course. I'm not working on silver because at this level it is too valuable for me to waste. That's why I was wondering whether you can suggest me a metal that I can practice on and have a similar experience.

[@drflavorflave3536]

Try copper. Copper is pretty close to gold and silver. It's right in between on the mohs scale. The workability is quite easy as well

[@somedutchguy7582]

Alpacca (also called new silver, German silver, nickel silver, ...) works really well.

[@Johollister]

If my job ever opens back up I want all the sales people to watch this to see what I have to do.

[@ernestoto22]

OK,question: how to fill holes from casting or after soldering?

[@Ken_Dalton]

Use solder. U shouldn't really have holes tho. Sounds like something went wrong. Maybe the mold wasn't hot enough, or the melt not being hot enough.. Tip I got from Andrew was, when u think it's all. Melted nicely keep Goin another minute or so U could try patch holes up with Flux and solder tho if u need to rescue the work

[@MooGoshi]

Hi - unfortunately you can't just use solder to "patch up" flaws from casting, it will fail it's assay. If the hole is shallow it's best to file down to smooth metal, or burnish over some metal from the high spots. If it's deep & narrow you can drill it out, & plug the hole using a piece of wire (rivet), & hammer to fit. Alternatively you could cut out shapes to make a pierced design, or even set small stones in their place... Lots of options!

[@DirtyPlumbus]

Holes is your castings are likely from trapped air or not getting your metal hot enough.

[@corneliuscenac2373]

Found your channel through this video kzbin.info/www/bejne/iHjGl4d8rrV9ntE by Pablo Cimadevila . Im new to this and i really love making things, thanks for all of this :) Cheers.

[@eivindkofod1774]

Andrew, let me continue the schoolmaster joking from yesterday. Today you called your calipet a gauge and that's fine. But you called your digitsl gauge a Vernier gusge and that is wrong. Mr Vernier invented the mechanical 10:9 scale on mechanicsl callipers. Your digital gadget does not have such scale. So it is not a Vernier gauge/calliper.

[@Ken_Dalton]

He ain't the only one that calls them verniers. And is it really that important to u to correct all his slips of the tongue an mistakes? I'd love to see your perfect videos?! 🤔

[@senghoucheong666]

OK... It's a ruler