Here You Can Remove And Reinstal It With Out Pulling Down The Tranny.
Пікірлер: 19
@isaacperales95809 ай бұрын
Recently after very cold day, my Ford F150 2002 start leaking coolant (water) from the flywheel. What can cause that? Those seals that I see behind the flywheel? I think the name is Expansion Engine plug or freeze plug! Thanks!
@JM-AUTO9 ай бұрын
the freeze plugs, when they go bad they leak.
@charlierobertson34324 ай бұрын
Don't know if you fixed it yet. On the f-150, under the intake manifold, it makes a valley between the heads. In that valley is a water line that straight out of the back of the water pump. That line has a bad problem with rusting out. Water will flow to the back of the engine and run down between the engine, and the bell housing. There are also two freeze plugs in that area.
@devon3ddd4 ай бұрын
I need to see how to do it in the f150, the top 2 bolts. What’s the secret or socket extension swivel combination?
@JM-AUTO4 ай бұрын
hi, very long xtension and 13mm swivel socket you get one out by the right side n the other one by the left side of the tranny. thanks for visiting this channel
@devon3ddd4 ай бұрын
I’ll definitely give it a go, thanks 🙏🏿
@hihello-qc8tz10 ай бұрын
How much for this job?
@tayratliff7777 ай бұрын
Is this the same for a 2000 ford explorer
@JM-AUTO7 ай бұрын
hi thanks for sharing, no it is not the same, since you most likely will have the 4.0 or 5.0 liter engine on your explorer.
@tayratliff7777 ай бұрын
@@JM-AUTO thank you so much for the quick reply! And thank you for letting me know. I just wish we could get this car going. My husbands trying to fix it. My husband went to start the car and it would turn 3 times and then make clunking sounds and not start. You can hear the whizzing of the starter engine the whole time but that’s it. He was finally able to get it started every once in awhile the first day or two but now it turns over and does the whizzing sound and that’s it. It won’t start. He took out the starter and tested it with a battery and cables. He said it seems fine (a little rough sounding- but fine). We don’t know what else it could be.
@JM-AUTO7 ай бұрын
@@tayratliff777 the fact that the starter pinion comes out and turns it does not mean is good try to bring it to a place where it can be tested, I also have videos on how to test the starter when they come out and turn but they are bad, when they are tested out of the car they can come out and turn easily because they are not doing any thing but to turn the engine over they need so much power n be in great condition, do you have the check engine linght on? if yes scan it and see what codes are stored in the ECM. let me know any thing.
@XBLmr9 ай бұрын
How much for this job located in New Jersey
@JM-AUTO9 ай бұрын
about $500 or 600.
@XBLmr9 ай бұрын
Would I have to bring it To you…. Or would u come To me …. I can help while you Fix it
@desmondbishop1246 ай бұрын
What's your address for the shop
@enterBJ407 ай бұрын
According to you ,why does this happens?
@JM-AUTO7 ай бұрын
Because perfect alignment of the engine and transmission are not possible, the flexplate can absorb the minute misalignment. As misalignment increases, the flexplate flexes more. This continual flexing eventually causes the metal to fatigue and the flexplate, most of the time from all of the above the flexplate end up overheating and then is when it breaks, also this flexplate is too thin for the big engine and tranny, so clearly the engine, transmission and misalignment overpower the flexplate.
@enterBJ406 ай бұрын
Thanks for answering.
@brianstehle97245 ай бұрын
can you improve alignment? my flexplate keep breaking