Ford F-350 Platinum 2" Shifted Wheel Spacers 37x13.50x20 Nitto Mud Grapplers

Truck has a 2.5” leveling kit with 37” grapplers and 2” shifted industries spacers.
#nittotires
#fordsuperduty

[@bradkvick1382]

Beautiful! Everything about the truck, lift tires and spacers is just right.

[@RockyRohde]

Thanks!

[@finao8231]

Impressive truck but what's more impressive is the size of your garage. A mid size truck is the biggest you can fit here in Hawaii. F250 is my dream truck, but will have to wait until I can put it in a garage 🤙🏾

[@knowledgeseeker5393]

Thanks for doing this video. I really like the factory rims on my 23 f250. I was always wary of doing spacers because I had heard horror stories. I think I will try 2” Bora’s. The look you have is what I want. Also thanks for telling us about needing to bore the rear spacers for the heavy duty package as that’s what I have.

[@RockyRohde]

No prob.. thanks for watching! Check out my 24 limited video on my channel. I did the 1” Bora on it..

[@garybain6780]

I would put a little Never Seize around the hub or you might not be able to get the spacers back off without beating them up if you want to remove them, especially in a snowbelt state where salt is used.

[@RockyRohde]

These have two notches in the back for removing with pry bar

[@antimatter_7.3]

Thanks for making this video!! Mine wouldn’t go on either so thanks for the help!!

[@dcrump]

Thanks 🙏

[@michaelhill4961]

I ordered 4 for my 2019 F-250 KR. It has 37s on it and rubs. I dislike the idea of kidding ride of my chromes wheels so I’m gonna give this a try!

[@CappyG430]

Where did you find the half inch bumper spacers?

[@RockyRohde]

One up offroad. I have them sitting on my garage floor.. If you pay shipping I’ll send them to you. Contact me on Facebook messenger

[@Lumpschlevot]

Thats a good look. It doesn’t look like you have any issues with garage height clearance. Is that a standard height garage door?

[@RockyRohde]

I have a 9x9 and a 9x18 on my garage..

[@Lumpschlevot]

@@RockyRohde Thanks. Those seem like high doors. I have a 2024 F-350 KR trim on order. Production is scheduled for the week of April 15. I want to have some things done at the dealership but I am not sure what will fit in my garage. My doors are 7 feet high. Will have to figure this one out.

[@DM-tf6mk]

Looks great!

[@N0M4D_22]

Awesome video very informative I did have one question, do you think it will still rub if you didn’t have the front bumper spacer installed?

[@RockyRohde]

2” wheel spacers require bumper spacer. 1” did not

[@N0M4D_22]

@@RockyRohde but if it’s a 1” it will probably run the radius arms and sway bar correct? If I’m running a 37 by 13.50

[@molonlabe7750]

Wheel spacers come with a free daily dirty truck.

[@wanderingdaze7018]

Are you on stock suspension?

[@RockyRohde]

2.5” level

[@ShawnWing-t1o]

This is more my taste. You have decent sidewall, lots of tire surface and it looks really damg good. You kust need some wheels. It looks great but some new wheels wpuld really look good

[@lohrke]

Was the speedometer affected at all because of the larger tires?

[@jonathanodom4743]

Got mine from shifted..came bare aluminum, not powdered

[@rogerstewart5140]

Sharp ride.

[@calebkildow6906]

@rocky do you have to run the bumper spacer with this setup? I’ve seen both answers and am just trying to decide

[@RockyRohde]

I did with 2” spacers.. with 1” no

[@Eriklindmark-mk3ph]

What air bags are you running on that truck?

[@RockyRohde]

ReadyAir with compressor

[@RockyRohde]

Readyair

[@BIGRICKLITTLERICK]

Nice video learned a lot! Question for you I have leveled 2022 SD truck and same tire but only 35/12.5 tires, really want to order the bora 2" spacers but really have no idea if it would rub! Since you have 37 and barley and issue with bumper do you think with 35 I would be ok? Sorry for the long Question. Thanks just trying to get it right!

[@RockyRohde]

2.5” level with 35’s should clear no problems with 2” spacers

[@BIGRICKLITTLERICK]

@@RockyRohde 👍👍👍

[@sdavis76]

I am running 295/65r20's on stock wheels currently with zero rub

[@johncetin8159]

Where did you get the spacers to accommodate the 4 inch axle?

[@RockyRohde]

Bora Motorsport tech website. Call Lenny and tell him you need two rear HTC spacers. These have a slightly larger bore to accommodate larger axle.

[@kylestrange1]

I have a couple of questions. First off, do you like the 1” or 2” spacers better? Second question, which thread pitch are you running? I have a 2022 F250 King Ranch and just ordered 37x13.50x20 Mud Grapplers. Currently have Toyo M/T but would like a the truck to look a little “beefier” without overdoing it

[@RockyRohde]

1” spacers work great I prefer them over 2”..

[@MrChipTalk]

@rocky I need four of those exact shallow caps. Can you tell me where I can order them?

[@RockyRohde]

Ford.. tell them you need 2wd front caps..

[@erickmatias1011]

How do you know what axle you have?

[@RockyRohde]

Small sticker on axle tube will tell you 3.31 or 3.55

[@lbates0311]

So pretty much you have to cut the lugs when running anything less than a two inch spacer?

[@RockyRohde]

Yes.. you will have to cut some off even with 2”…

[@hayden-px4vv]

@@RockyRohdehow much did you end up cutting off?

[@JMM021997]

2:50 I have a 2020 f250 with the high capacity axle. Can I buy the 2wd rear center caps and use them on my rear axle? Thanks.

[@RockyRohde]

If you are running wheel spacers

[@caysonwells9648]

hey i have a f250 with a 3.5 level kit do you think i could run 37x13.50s with these and not rub?

[@RockyRohde]

You will clear them fine.. They will rub radius arm and sway bar without spacers..

[@gjolinares23]

Too bad it’s not easy to just find and buy replacement parts to convert for different bolt patterns. I don’t cares that much about the spacer part but I want to put new GM wheels on my Silverado HD 😅

[@kailenmadden3003]

Would I have to cut the studs on 2” or should I just go with 2.5” 2020 gmc 2500

[@josuelabrada5814]

Can they hold weight ?

[@RockyRohde]

Yes

[@kennydebaene2279]

Why did you get rid of the American forces so quickly?

[@RockyRohde]

Just wasn’t the style for me..

[@eriks6313]

Will this rub on a 4 1/2 inch lift ?

[@RockyRohde]

No it should not

[@erickmatias1011]

I have a 2019 f250 with the sterling real axle (12 bolts) will the lip on the rear ones have to cut like yours?

[@RockyRohde]

If you have overload leaf springs yes. If not they should be the standard..

[@Gentner91201]

Do you lose towing capacity with these shifted industries spacers?

[@RockyRohde]

No

[@Gentner91201]

@@RockyRohde oh okay. I was always under the impression you weren’t supposed to tow with aluminum spacers. Love the rig

[@RockyRohde]

I have always used them. It is important to check torque every rotation. Buy good hub centric. Bora or Shifted.. If they are not hub centric don’t use them..

[@issackcasarez1907]

Do have part number for the hub caps

[@RockyRohde]

I don’t.. Dealer can look them up.

[@CarlosFlores-m4y]

What size wheel is that stock? 20x8?

[@RockyRohde]

Yes

[@jeffguthrie2600]

When you get your new Ford. Will you sale this Fird?

[@RockyRohde]

My wholesaler usually buys them from dealer and I get tax credit on my new truck.

[@jeffguthrie2600]

What color is your 2024 Ford?

[@marlonjose5921]

I have a 20 250, where can I get a set of 4 2”spacer

[@RockyRohde]

Motorsport tech Bora spacers… This is all I run..

[@marlonjose5921]

@@RockyRohde Thank You. I have my truck for 4yrs but hesitant to try spacers because of bad stories i heard. But now i will give it a try… is it safe if im pulling my 38 ft RV?

[@RockyRohde]

@marlonjose5921 I have pulled large toy hauler RVs for years with them. Just check torque and inspect every rotation..

[@jtother1242]

What size lift?

[@RockyRohde]

2.5 ready lift with tremor rear blocks

[@chrisg50096]

Why does it say carli

[@sdavis76]

@@RockyRohde what size are the tremor read blocks

[@RockyRohde]

@sdavis76 tremor blocks are 3” and fx4 are 2”

[@austinmelton8306]

I’ve got the same exact truck and spacers and tires you have and mine is rubbing on the front tires closer to the front door on that plastic piece what did you do different there?

[@austinmelton8306]

Did you take off that little black piece or cut it ?

[@RockyRohde]

It’s gone…

[@user-tx2ck7uj4u]

Did you cut the metal or bend it back? My truck still clips the metal even with the plastic gone

[@RockyRohde]

I had the Carli arms and it helped some by pushing axle forward. But I did some trimming and hammer work. I am going with 1" spacers this time to avoid the rubbing.

[@kevinkozlowski1463]

near seen dual air bags

[@kellysimmons602]

Does this help with tires rubbing? My front tires rub when running after market 37” wheels

[@jayknot6684]

No, it will make the rubbing worse because it increases the arch the tire makes when turning.

[@croomrider9785]

@@jayknot6684only with aftermarket wheels with negative offset, stock wheels and spacers make it so you won’t rub on components

[@Step-n-Wolf]

​@croomrider9785 he had to move the bumper out, so not true.

[@calebmcgowan2090]

Comment

[@JAG6.7]

How is everything up with the spacer kit?

[@CarlosFlores-m4y]

What size wheel is that stock? 20x8?

[@bradkvick1382]

Yep, 20x8 +40mm offset.

[@CarlosFlores-m4y]

What size wheel is that stock? 20x8?

[@doo0ge377]

Yes

[@bradkvick1382]

20x8 +40mm offset