Ford F450, VIAIR Onboard Air System Install

[@mattschultz1878]

A man after my own heart. OCD, and everything needs to look as factory as possible. Very nicely done, sir.

[@daveprather9960]

I wish I could find a bracket like this for sale or the CAD for it. Great fit and strong way to mount!

[@justinn3472]

can you share some links for the parts you used? would you be interested in making/selling the mounting kit?

[@gtowncasey111]

Couldn’t have done it better myself. One thing I would have tried to do was mount the compressor right side up. Good work

[@stickbogart3657]

👍👍👍 I don’t know why so many people mountain air compressor in a dirty wet environment. I just don’t understand that I’m using. 4 VIAIR air compressors for my airhorns, and for my ability to air up a flat tire for me or somebody else. All of my equipment is not in the weather and it’s not in the water or the mud in the dirt. It takes me only seconds to remove one of the. 4 VIAIR air compressors if they fail for any reason or get worn out I don’t have to crawl underneath my truck to take something out that’s no longer working. I believe you prolong the life of anything if you keep it out of the dirt, the water and the heat from the freeway, if you do not mounted underneath of the truck. Keep in mind I own a 2022 Nissan frontier crew cab I have a 2.5 gallon air tank and I have. 4 VIAIR air compressors and a quarter inch manifold that route the air pressure to where I wanted to go and none of my equipment. All the electrical is in the dirt water or mud. Who wants to crawl underneath of a truck to service there? Air system not me

[@xcntrk75]

Most folks with real work trucks need their entire bed for hauling and capacity. Placing tanks and pumps in the bed eats up that precious space. Interior is out of the question due to excessive noise the pumps make. With a Frontier you probably don’t have to worry about these issues and therefore have plenty of room to mount in your passenger seat.

[@stickbogart3657]

Thank you much for your input. I’ve always wanted an air compressor system for my pick up truck that has rapid recovery capability. The reason I put the system together is because there’s so many people out there on the freeway. They do not pay attention to what they’re doing. Usually they’re playing with the phone while driving down the road not staying in their own lane we all know what happens when your car gets wrecked. The value is diminished dramatically number one and number two it winds up in the shop to get repaired. It’s going to be there for a long period of time so I make sure that I have the ability to give them a loud wake up call to stay where they belong and away from my truck Also, it does not take me long to have 150 psi. I have run it up to 250 psi just to pressurize the system to make sure that it’s got no leaks Sometimes I use it to help others who have a flat tire and when I opened up the toolbox to connect my hose to inflate the tire, they are impressed with what they see The airhorns are in the grill you can’t see them unless you really look for them and I have them facing towards the ground. That way if I drive my truck through a car wash no water is going up inside of the airhorns I added another airline that goes up underneath the back of my truck so if I want, I can add a second set of air horns on the rear of my truck I’m sick of the stupidity on the freeway. That’s why I built the system that I put together .

[@Diesel_ftw]

Excellent work! Love the setup. Good job

[@1980zz4]

Very nice fab work. Also interested in your mounts. Please let me know what your charging for them. Thank you!!

[@ambassadorTenney]

Are you still selling the mounts? Awesome install and video. Very clean.

[@clerissonmesquita]

Thank you for your outstanding job, highly appreciate it, have a great day.

[@texasfuncouple]

Good evening, I know you only produced a limited number of your mounts and have since sold out, just checking to see if you had planned to make another production run? I am sure you have been inundated with requests, it is a very cool system.

[@LeadTechnicianIII]

I have The Chief on my car . I love it!

[@edwardh1003]

Nice install. The splash guard on the bottom was a nice touch. How has the system held up to snow, moisture and dirt?

[@dennishazeltine7877]

Great video...I'm interested in this for my 22 F350 but I live in NH and I'm concerned about the winter months we have and this being able to with stand the salt and slush ??

[@landog59]

Very professional setup 👍

[@cjyates3049]

The radio station in the background sounds familiar 😂

[@Roadrash429]

Now that this video is a couple years old, 2 questions? Is it still holding up? Considering you mounted it directly in front of the back tires. Perfect place for everything your tire throws off it, to go right into the tank/compressor? And second question.. VI- air (you know like an "i" sound. Not an "e" sound) the one thing they say is do not mount upside-down.. does the pump even still work?

[@sydneymokoi6666]

Nice setup bro 😎

[@mike_adams]

Great video. I’ve sent a pm requesting pricing.

[@MarbryPerformanceHorses]

Great video, nice details. The unit really isn't supported by the inserts, it's supported by the two bolts.

[@xcntrk75]

Hey thank for the watching! The whole unit will hang from the frame inserts without the self-tapping screws in place. I have now made 20 of these and I have tried this repeatedly. All the weight hangs down vertically from the inserts, the screws just keep the inserts from sliding out as that weight can shift from side-to-side in corners/bumps/etc.

[@TheRoadTaken]

@@xcntrk75 i believe he is referring to the bolts that attached to the 2x4 inserts - you welded the nuts in place.

[@TheRoadTaken]

Very nice. Do the rear wheels throw any debris onto the compressor or dust shield? I'm picturing riding my bike as a kid and the rear tire shooting water onto my backside of my pants.

[@AStanton1966]

Nice clean install. I wish you were my neighbor when I installed my Godfather air-horn. Putting a manifold together for those 6 trumpets was a pain,.

[@cadexim]

Impressive. Nice job!

[@Jason-nt5gr]

Great setup!

[@kevovernon]

So no pressure gauge installed? You would have to use a manifold

[@ChrisNichols-jn1zg]

Not sure what I'm doing wrong with the wiring. Followed your instructions with wiring the relay without any luck. Regarding the solenoid, 85 or 86 goes to one of the solenoid wires and other solenoid wire is grounded, correct? Thanks!

[@xcntrk75]

Follow the diagram on the relay housing. Sometimes different vendors switch the pin numbers around.

[@ChrisNichols-jn1zg]

​@@xcntrk75 yes sir. The diagram on my relay is identical to your relay in the video. When I activate upfitter 1, I hear a high pitched sound from the relay and my factory horn still sounds when pushed. Maybe the relay is bad. Two wires from the solenoid, one connected to 87 and is the second solenoid wire grounded? Thanks a lot for your time.

[@troyemmanuel3985]

Great video, very good method of set up, how much did you get the kit

[@user-fs1sc9yf9y]

Very nice install! Can you tell us where you found the rear air chuck cover??

[@xcntrk75]

I had it kicking around. You can get them at trailer part stores.

[@user-fs1sc9yf9y]

@@xcntrk75 Great, Thanks

[@ddboring]

Nice fabrication 👍

[@salcigar]

I don't see a regulator in your install. I have the same horn running off a 1.5 gallon tank and two Viair 444c compressors. With my air regulated down to 85 psi I can get a lot more usage from my system before the compressors have to kick on and re-energize the tank. The regulator is only on the output that feeds the horn.

[@andyburdett5701]

Very clean install! Would you be willing to share or post the drawing template for the tray, mount and dust shield? Looking to put the same system in and yours turned out very clean. Looks like the F350 has the same frame block outs and should work.

[@xcntrk75]

I am now selling these mounts as a turn key kit. Dual and single compressor kits. Please contact me for details.

[@andyburdett5701]

xcntrk75 contact info?

[@donsvideos1985]

@@xcntrk75 How do I contact you I am interested int his setup for my 2018 F250 crew cab. Thanks.

[@xcntrk75]

@@donsvideos1985 Just replied to you email, thanks!

[@1dayatime785]

@@xcntrk75 whats your contact info?

[@Hokuhina27]

How much for the brackets, I'm interested. Thank you

[@richardlyles2883]

How much for the bracket? What is the viair kit part number?

[@ericgraham5697]

2021 F350, interested in this kit

[@johnlarkins1651]

Nice rig! How did you connect the compressor to the upfitter switch from the relay? I have a 2016 F350 diesel. There are 2 , 25 amp and 2, 10 amps. I’m trying to use one of the aux switches to turn the compressor on and off..

[@mleukus]

on the horn relay - did you just ground the black and one of the two relay wires?

[@Tmil1035]

How did your wire the solenoid?

[@dennishazeltine7877]

I see people asking if your selling the bracket and am I to understand your selling the whole kit ? If so I'm very interested could you message me please, Thank you

[@joshuawhite5979]

Clean install!

[@mrmotofy]

You're clearly a fabricator if you have a bender for 1/4" and a dimple die.

[@Warpetrie]

Definitely going to consider this setup for my vehicle. Love the way the horn is wired too, would have never thought of that myself! Would it be possible to wire the air pump to the ignition or is the startup and compressor too much of a draw to have simultaneously?

[@xcntrk75]

Of course! This is the way the compressor kit is intended to be wired. It comes with a relay and sufficient wiring to wire the constant/load directly to the battery and the relay trigger off an IGN circuit.

[@vpnman]

If you're still selling the mounting kit, would be interested. Couldn't find an email on your about page to make contact. Thanks!

[@mleukus]

did you run 1/4" air lines? for the chief? where did you mount your gauge?

[@MrDraper38]

Great work.

[@scottcoleman7304]

Hey really nice setup man! I have a question about installing the air chuck at the rear bumper. I get there's the air chuck in front but what screws on to the rear side of it that squishes it tight against the metal there?

[@xcntrk75]

There's a fitting that goes into the air-chuck, it has a shoulder and I sandwiched the plate where mounted between the chuck and that shoulder.

[@mikemacri7502]

Great job, are you interested in selling me the same mounting kit.

[@prashantsharma1148]

So I know your install is on a truck and all hardware is under the truck bed. Can the compressor and tank be mounted within a car’s trunk? Or are there safety concerns ? Thanks .

[@mrmotofy]

Trunk is better location since no real water issues

[@sellmad1]

How do I contact you to get the mount?

[@danielloflin3374]

I’d like to buy a mount

[@supergcrash]

Great video

[@craigmumma8161]

Would you be willing to share that file? I have the same truck and system.

[@markzimmer3841]

I have a 2008 F250 Super Duty. I understand you have these mount kits available. I am looking at the medium duty ViAir system. I would be interested in buying the kit.

[@xcntrk75]

Hi there. This product is available but the installation system currently only fits 2017+ Super Duty.

[@craigmumma8161]

I just saw that you are selling these brackets. I would be interested, please let me know how to purchase.

[@xcntrk75]

Only made a limited batch, all sold out. Thanks for your interest.

[@tommybash6322]

Do you have a blueprint for this that you would be willing to share

[@sellerbrake]

Do you have any more of your mounts available?

[@xcntrk75]

Unfortunately no

[@derekpowell3386]

2021 F-450 interested in your kit, please PM

[@niranjanaholidays7628]

How much ?

[@210craig1]

Are you still making the mounts?

[@xcntrk75]

Still producing, first batch due next week.

[@210craig1]

@@xcntrk75 great let know when they are ready

[@ralphhouseholder2702]

@@xcntrk75 I am also interested in the mount for this system. I have a 2021 Ford F450 coming this month and want to install exactly like you have.

[@MattTat24]

@@xcntrk75 emailing you now.

[@ericgraham5697]

@@xcntrk75 how much for the bracket?

[@210craig1]

Excellent video. I sent you an email requesting pricing.

[@xcntrk75]

Did I respond to your email already? Everyone who emailed and I have responded at this point. First batch of mounts should be done next week.

[@chuckwagner9417]

@@xcntrk75 How do get one of these?

[@chuckwagner9417]

@@xcntrk75 Could you please let me know if this bracket is available for sale and how I get one.

[@xcntrk75]

@@chuckwagner9417 these are no longer available. I produced a limited run and they’ve long since sold out.

[@nickadams2951]

I wired my horn the same way

[@majorcheese2345]

Can you run power tools from that set up?

[@mrmotofy]

Need 3/8" or 1/2" line straight off the tank to a regulator then to the coupler...then a guy could. But not for long on a 2.5 tank. And that's a low volume pump. Use Milton type V couplers for better flow/volume

[@jasonturcotte3532]

Wolo the chief not supose to sound like this… Check my video if you want to hear what it supose to sound like

[@daveprather9960]

Sounded good to me 😊

[@stevesimpson4840]

Are you still selling these? If not how about the drawings so I can get it cut?

[@joespanojr]

Great set up but the music is taking away from you speaking

[@daveprather9960]

Come on man!

[@thepidget3837]

Looking for a set up.. please contact me

[@jpascaln]

Two things! First, you honk at little old ladies in the crosswalk when the light changes? Second, a 40 amp fuse on 30 amp device is LESS protection, Einstein.

[@daveprather9960]

He didn’t want to overload system obviously so he’s definitely a lot smarter than you DA.

[@daveprather9960]

Wish you still produced and sold that bracket. Great work. Anyway I could at least get the CAD for it?