Ford Focus Engine Mount Vibration Repair

Only buy Ford Engine Mounts you can get them Here- (check part fitment guide)
www.amazon.com/...
This is the Blue Loctite I use in the video-
www.amazon.com/...
Here is the safe and proper way to change out that engine mount including how to test for a bad mount! Torques specs are for 2009 2.0l Duratec Engine yours may vary slightly but these specs can be safely used on any model year.

[@jmsjags]

Just replaced the engine mount on my wife's car. There is no way you can go wrong by following this video. You even gave us the torque specs and everything! THANK YOU for this!!

[@jonataseuuk]

Unler the nuts inside the chassi snaps out and rotate with the bolt!😅😅

[@DashPadGames]

Finally got around to changing the passenger side mount.. and the difference is like night and day! My focus feels like it's literally gliding when it drives, it's soo smooth. I had to watch this video again today to gain the confidence to do the job and it took me about 45 minutes. Thanks again for the informative video!

[@mikethomas3819]

+DaPaRappa I've been thinking about doing mine, but I don't feel too good about putting a jack under my oil pan. So, it wasn't too bad then?

[@DashPadGames]

psychotogen1 Yeah it wasn't bad at all. Just make sure you have a nice sized block of wood to put on the jack under the engine oil pan. I jacked it up slowly because I was scared, but it does spread the weight out making it easier to lift the engine.

[@Wk32eze]

DaPaRappa i finna do it soon scared tho

[@DashPadGames]

Young Reese Good luck

[@rahulg.4663]

Young Reese P

[@yoyoyoyo1999]

Thank you very much, just did my 2010 Focus yesterday and it is so smooth now!!!. Wouldn't have done it without your video. Thanks. Cheers.

[@190055joe]

Good job good to see someone clean the parts prior to assembly and using a torque wrench to avoid damage and making it easier for the next person.Thanks for the video we need more mechanics like you.

[@FordTechMakuloco]

Thanks!

@@FordTechMakuloco You're AWESOME!! LOVE your videos!! My mom has a 2011 Focus SE. Always doing the work on it when it needs it. She has the same problem. I am pretty sure it's the motor mount. If it is, should the driver's side mount be changed too? I am just thinking about changing things in pairs like suspension parts. Thanks in advance...👍😁 UPDATE ...The mount(s) seem fine. I think it's her muffler. It did have a few small leaks on it on one end of it. I patched them up but a s***load of water came out of it. I think it's shot inside. Rusted from inside out. Should I buy an OEM muffler from Ford or are the aftermarket ones just as good? Thanks in advance....👍😁

[@GRIMREAPER76IA]

Thank you very much for this great video. I just finished replacing the engine mount on my 2009 Ford Focus SEL and I was amazed at the difference it made. I am a very mechanically sound individual and the entire repair only took me 25 minutes. I was able to find the engine mount cheapest at AutoNation Ford Parts in White Bear, MN. I ordered it on 11/17/15 and it arrived on 11/19/15. Thanks again for all the great FORD videos. THE BEST NEVER REST!!!

[@cashwilson2571]

I’m from mn too Pequot lakes area

[@95scort]

Thank you very much! I just replaced the passenger side motor mount on my wife's 2010 Focus at 86k miles like the one you replaced in this video and the difference is incredible!!! She literally asked me "did my car start?" when she turned the key because literally 90% of all the vibration was GONE! $132.xx plus tax at my local ford dealership but it was worth every penny! I replaced it myself by the way in just a little over 15 minutes...

[@rotatingwah]

Thank you so much for all the details, your tutorial made this quick and easy. Best part is that the dash, the doors, and the window posts are silent now, and can look at the rear inside view mirrors, and they are vibration free! Thrilled with the results!

[@alexmikhael5061]

did your viberation smooth out at HIGH SPEEDS??? or was it constant always there with this mount being bad? my viberations ''go away'' at 73 plus.... eh... lol

[@willb2908]

Thank you so much for the great video. Bought the part and installed in under 30 minutes. My elderly mother in law had grown so used to the vibration that she didn't notice a problem. She certainly noticed the improvement after the repair. Thank you again!!!!

[@Watts378]

DAMN!! Like a brand new car now! Mine looked in great condition but decided to change it out since I was going to tackle the alternator. Was thinking of turfing this winter beater but gonna keep her now. Great vid man!

[@Dr.LessCharacter]

After watching sev vids each time I repair 1 of my Ford's i always seem back at your videos. Kudos to you!, everything worked out exactly as you indicated. My grandfather Head Mechanic over 2 international trucking lines as well Ford, Dodge, & GM

[@groundedinfirstprinciples383]

Thank you for listing the torque amounts. Mine was rattling so bad it cracked the windshield. The mount was disintegrated into two separate pieces. WOW WHAT A DIFFERENCE! Simple job! A note of difference from all the other videos I have seen, including yours.....My passenger motor mount stand did not have a 6th bolt underneath. Mine was removed by removing a metal subpost(like Tom Crawford below). Altogether, A simple procedure, and it runs so quietly now! I got my replacement piece for $20 bucks from a parts wholesaler(I never pay retail). Thanks man!

[@gertis7420]

Great video. Before I found this video, I was thinking of doing the test that you did, but i didnt know if it would work, now, watching your video, gives me confidence that I will know for sure if my mounts are bad. Thanks.

[@johnnytheturtle]

Used your video to replace on my 2007 ford focus 4 door with 184k miles. Made it a 20 minute job from start to finish. Thanks!!!

[@rmac7612]

the detail lifting the jack to take the weight was #boss ..great stuff

[@DashPadGames]

I dreaded the day I'd have to do this because I'm so scared of putting a jack under my engine to lift it. But it does look like an easy job. I'll be doing mine this Sunday. The only thing that differs in this video is my coolant reservoir has to be moved aside since the overflow and coolant tank is all one unit in the 2005. Engine mount is exactly the same from what I've seen. I'll be so happy once that vibration is gone.

[@mtmals9786]

just finished replacement motor mount install. Worked to spec.....lock tite.....correct torques...bolts cleaned on wire wheel...jacked with buffer board. All went exactly as you instructed. Replacement mount was Motor Craft. Very quiet engine now. Thanks for your help. mike

[@patrickstevenson8869]

Did this replacement today and OMG! what a difference. I replaced the driver side mount first thinking it was the culprit. But even after that, when I would open the two back doors both of them shook violently! along with the steering wheel, and everything else in the cabin. Even the battery shook after the driver side mount was replaced. So I was confused as to how it could be the passenger side since the battery was directly over the other mount! But, NOPE, I replaced this passenger side mount and It took "ALL" the shaking away. The car shifts better too! Man what a difference. Best 100 bucks I ever spent! (Not really, But its up there!) Thank you for the informative video. I hope this brings sanity to anyone looking to solve this issue. BTW, The initial test you recommended by slightly lifting the engine to relieve pressure on the mount was my green light that is was probably that passenger mount!! Happy Holidays.

[@ctapmgriley]

Thanks for the video showing diagnosis. Worked perfectly and was able to fix the terrible vibration quick and easy!!

[@kahcycousins7103]

I've been trying to change my idle pulley and figured I didn't have clearance due to the bad mount. This confirms it and I'll have even more room and confidence to change two parts in one go. Much appreciation!!

[@FordTechMakuloco]

I used a paint pen because a little brake clean and it come off, but a sharpie marker will do also. The anti roll mount is underneath center backside of the engine, mounts by where the trans and engine meet looks like a figure 8. Rocks get stuck behind it where it mounts to subframe. I would check this out first as it happens primarily in reverse when the engine torque loads the mount rearward. Search for tsb 8-5-6

[@adamhg985]

Got the mount from Oreilly. It looks a little different. The brackets are a bit different on bottom even though the holes are an exact fit. I actually had to file a little off the bracket closest to valve cover it was almost top snug making the studs too angled. Just fyi if you get the oreilly one. $112. Great vid runs a whole lot smoother once installed

[@henrikskrubbeltrang5360]

Fantastic Video - thank you very much for this fine guidance ! Today I changed this mount on my Ford C-MAX, 1,8 petrol, Trend from 2004. I have been driving with vibration issues for more than 3 years. My Ford service changed the button mount for about 1 year ago, but no big difference. Today I therefore changed the upper right mount myself. I used a Febi Bilstein mount, Germany quality, WHAT A DIFFERENCE - I HAVE A NEW CAR NOW, allmost. All vibration problems are gone now, it´s absolutely fantastic, I have forgotten how much comfort the car had before. There was no visual defects on the old mount, but I can se a small difference after mounting. The engine is about an half centimeter higher in the right side now, so the old mount just lost its strength over time. All the best from a happy dane ...

[@StoicWisdomTube_]

THIS VIDEO DESERVES A REWARD 🎉❤

[@jaredshelton4718]

You made this look so easy. I have a 2010 Focus with only 55k miles and the vibration is terrible. I'll be doing this soon.

[@omarsleiman1261]

Did you do it yet?

[@autohelix]

Thanks for the torque specs. 20-minute Job, and done much better

[@mgregg1921]

Thank you for posting this video bro. This is going to make fixing my daughter's car so much easier to see it being done in real time. You're awesome!

[@mtmals9786]

Just ordered my right engine mount F.focus 2005. Can't wait to drive in for routine inspection after I perform your expert procedure. They expect $300 bucks for the install....when I will have already done it. LOL. Next will be rear drum break overhaul. Thanks for your great series.

[@NWSubie]

Great video. I think you may have helped me diagnose my U.S spec 2010 Transit Connect van with the Focus engine and mounts. Van only has about 36k and the problem started a while back. Vibration is noticeable at all times. Most noticeable through the gas pedal. Tried jacking the engine up and the vibration went away. Hopefully it's the passenger side mount. I'm hoping Ford will pick up the tab as I complained about the vibration and have it in writing well before the warranty was up.

[@leorickt.9604]

Holy crap this channel is such a lifesaver

[@marcuscarrillo5118]

I used all the steps you described and successfully changed my motor mount today. Thank you for posting this and God Bless!!

[@jamescole3524]

had my son in the car while i jacked up the engine like you said to see if it was bad...jacked a couple times and it got smooth as heck...so i did what you said to replace...it went great...put it back together but it still has a vibe...is there another mount that can go bad? they said at the parts store that this was the mount for the right side...so can i assume theres a left...i felt like a real mechanic for a little while...your spot on on the directions

[@garryj7939]

Thanks for posting. Will be doing it soon. Used your other vid for valve cover gasket repair yesterday. Thanks again

[@washingtonredskin6574]

So I went out and bought this part made in USA for $180 CAD, did the change thanks to your instructions, and the results are great. Huge reduction in annoying vibrations, but I still feel a small vibration and I think it's coming from the Transmission Insulator mount under the battery box. When taking the tranny mount out, where should i support with hydraulic jack. engine or transmission. Quite sure shop manual still shows the support beam over the engine area, but vertically.

[@FordTechMakuloco]

+Washington Redskin Support the trans case the same way you supported the engine while the mount is out.

[@jordandickens6889]

I just kept putting up with the rattling and noise getting louder and louder, but it was getting out of hand. I inspected the mount and it appeared that the oil had come out and it was worn badly, so I decided to replace it. Like other users have stated, it is staggering the difference this makes. Its so quiet I cant hear it now, and its very smooth as well. Great instructions, save yourself a few hundred dollars and do this job yourself. I was told to get the part from the ford dealership though, they said the aftermarket parts wont be near as good and you definitely want to stay away from the 'solid rubber' ones.

[@FordTechMakuloco]

Yup the aftermarket units don't last near as long.

[@joegrage7239]

Thanks man, just fixed my son's 2017 in about 20 minutes. Easy fix and a big difference

[@AlmostADr2016]

Thank you for this! I feel like I'm driving a brand new car after replacing the motor mount!

[@FordTechMakuloco]

+AlmostADr2016 Yeah it makes a huge difference.

[@thedoctor2062]

Thanks! This worked for us. The test with the jack and then the repair. We did it in about 30 minutes. BIG difference in the vibrations heard and felt.

[@geekdiymechanic4539]

Hi, You've helped me in the past. I had a 2000 focus that went through three coils. You told me me about a potential wire grounding, and you were 100% right. Two strands of wire were left and were grounding on egr tube. Thanks! My question is about your parts link on this video. When I click it, it brings up is a dea mount. When I look on a Ford parts site, the price is significantly different. Should I purchase part from dealer? If not, should I stick to dea manufacture only? In the past, I have had the best luck with dealer parts, but they are just so much more costly. Thanks in advance for your great advice, experience, and insights.

[@manuelortiz7731]

The best ford guy in KZbin 👍👍👍

[@1dlb]

done - the hardest part was putting the new one back in .... thanks !! Car is much smoother now ....

[@187WCB]

@Mardy Crue. I have the same vehicle as you, and when I was test driving it from the dealership I purchased it from, it had the exact same issues as yours. The problem was this side engine mount was leaking fluid. I made them replace all the mounts with OEM before I made the deal and it fixed the issue. Unfortunately, OEM is the only way to go for that particular engine mount because it contains fluid and the aftermarket ones are cheaply made and don't have the required fluid if any at all.

[@Jonathan-L]

Is it reasonable to say that the engine mount fails due to fluid leakage? So, if the mount doesn't leak, then it should remain in good order?

[@atlas1122_]

Dude thanks couldn't find a video like this anywhere

[@mbaer5]

Just bought an 09 SE same color! Actually has a brandy new motor mount from the dealer (left the genuine Ford Part sticker on) pretty happy got it cheap with 115k and a book of service records from the dealer!

[@jeremiahobrien7030]

Thanks your video was spot on. serious vibration at idle, shifting to reverse or drive. Got a new mount at Napa, smooth as silk now! Thanks

[@fogman1956]

Thanks for the video, got the job done. My replacement part from O'riely was only the insert, had to pry old one out and then bend a tab to keep the new one in. Didn't realize going in the lift point on oil pan was critical to getting a good lift. If too far to the center it lifts entire car.

[@FordTechMakuloco]

If you lift too high it will lift the car yes.

[@fogman1956]

FordTechMakuloco I had loosened the motor side nuts and the motor was lowering even though had jack under it but too far to the tranny side of the motor.

[@rogerbeers2939]

I used your video to fix the mount on my transit connect, very detailed and was easy to do. Thank you for making this!

[@oswaldoceronsanabria5846]

I have the same problem on my transit, u did all the mounts or just the left side ? Thxs

[@rogerbeers2939]

Oswaldo Ceron sanabria I just did the left side. Haven’t had a problem since I changed it out.

[@oswaldoceronsanabria5846]

Thanks I’m gonna replace it this weekend. I hopefully I solve the problem.

[@NoAfilliations]

Great video, explained it very well. Bought a zx4 with a bad passenger side mount. I feel perfectly capable now. Thank you.

[@williamhank4565]

just got one used for 3k 120k miles with this paint and part its like new thanks allot man

[@moparguy37]

Thanks for your info....I replaced all 3 mounts. It was the bottom mount from the engine cradle to the tranny that made the biggest difference.

[@brianschuler1257]

Thanks for the video. Worked like a charm and saved me at least $200

[@MrWill1985]

I just got a second opinion Saturday and yes my passenger side engine mount does need replaced. Luckily the place that gave me the second opinion only charges $156 plus tax according to the invoice and the first place that mentioned it wanted $250. So I do plan to get it done at the place I got the second opinion from.

[@FordTechMakuloco]

Yup very common.

[@danielbornhoeft7803]

MrWill1985 I would be curious what type of motor mount they will use. rockauto.com is selling anchor motor mounts for 7 bucks a piece, motorcraft motor mounts are cost anywhere from $85-100 a piece.

[@zemoney954]

Ten Years later! Thanks a bunch Fr Thank You

[@FordTechMakuloco]

Not sure which bolts you are referring to but I am sure they are supposed to be there. Yes you can use ramps in the rear but make sure its in park AND parking brake is on as they are natural free rollers back there.

[@FordTechMakuloco]

Never seen the other side which is the trans mount go bad like the right hand side engine mount in this video. Go ahead and check it like I show in my video. Other thing to check is the rear anti roll mount under the car for rocks causing the vibration when the engine is loaded a certain direction.

[@michaelgawne4363]

" You are I am" was playing in the background :)

[@Jonathan-L]

How long are the originals expected to last in terms on miles traveled? And are the aftermarket replacement ones likely to last longer? And finally, is it just the right hand engine mount that is a problem, or should I be replacing any other mounts as well as the one shown in the video?

[@angyzoellner3140]

Thank you for this video. Very informative and easy to follow.

[@Samhain2323]

I really enjoy your videos and the work you do, you are very informative and helpful !!! With that said, I absolutely don't like the way you use your influence to make people believe that they should only buy oem products, there are many after market products that are just as good and even better than the original Ford parts !!! there are many after market products that are inferior and perhaps that's why you recommend them but OEM isn't the only solution !!! With proper research you can differentiate between the two !!!

[@FordTechMakuloco]

If there is an aftermarket product I would certainly suggest it, Have you seen all the videos on the Melling brand oil pumps? In this case and most other cases nothing but OEM should be used this is the voice of experience not personal preference.

[@k.c.8535]

hey, I just had this done today on my Ford Focus, cost 107 bucks, but it took them 2 hours where you did it in about 15 minutes

[@daniellaudman8580]

Purposely took 2 hours I'm sure

[@FordTechMakuloco]

yes unbolt anti roll mount and check the cavity for rocks and debri grounding it out.

[@superrodder2002]

I'm not the least bit scared of work, I can sit on my couch and watch someone else do it on KZbin ALL day long. LOL

[@gurutimes2]

best video on this subject ive seen.

[@sergiodjf]

Thanks for the video. I had the same issue on my 2004 focus zx5. I took it to the dealer and fixed it, it feels like new now. They also checked the brakes and found a damaged thread on the rear spindle. They suggested to replace both rear spindles down the road. Would you recommend buying OEM spindles? Or aftermarket ones are good enough?

[@FordTechMakuloco]

I have never had an issue removing the bolts for the anti roll. A little rust penetrant is advisable of course no matter what. Yes where are the pictures located

[@wonpak4737]

Thanks for the instructions. Just changed the passenger side mount on my 2013 and now it drives like a new car....aside from the transmission which Ford never seems to get working right. Still has that shudder in low gears.

[@IdeaSpyTwoPointFive]

Great video! I have a 2015 Focus 2.0 with the infamous DCT and it shakes at lower speeds, especially going up hills. Could this be caused by bad motor mounts? The car has 60k miles on it but it's a northern car.

[@Helioivo]

Thank you very much for de video. My Ford Cmax has the same problem, and now i can do it myself!! Thanks, from Spain.

[@rocmo9853]

Excellent video, and thanks to this I will change my own. However the link to Amazon for the part seems to be in error. Got mine ordered from eBay. Oddly enough I'm kind of excited to work on my car.

[@russmassery1880]

Thank you again! solved the problem with my 2011. With 80000 miles on it. I was surprised that it when bad so soon. My sons lasted till 150,000.

[@MrKen59]

Very well done - Thank you. A jack under the oil pan eliminated the vibration and was the test I needed. So is a factory part best in this case or will an oem part work from one of the big distributors? I subscribed to your channel. Wonderful.

[@becerrillo]

mine is manual transmition, Are the same auto and manual mounts? thank you great video

[@FordTechMakuloco]

Remove both bolt pull mount and check out the cavity it sat in the subframe. No engine support needed may roll a inch or so but that's it.

[@danielbornhoeft7803]

I'm impressed with the one handed repair job! hope to do this this weekend!

[@onlycodered]

Just got my new mount today. Thank you for the video.

[@FordTechMakuloco]

as long as the plate that touches the pan is wide like a block of wood to span the load out then its ok.

[@alexander-malafeev]

Thanks for the video! Where do you check torque specs?

[@fishalcoholic]

Best video out there for this repair. Thank you for the effort!!

[@FordTechMakuloco]

Your welcome!

[@dieselscience]

You've been a great help but I have a quick question...on the 2002 - 04 SVT models vs. the 'regular' Zetec - are they both the same part number?

[@jigmepeace4]

i am sure u save lot of people from rip ...u the best...

[@ahuman5150]

Very detailed and clear explanation. Than you very much!

[@steveblan1512]

Good job demo straighting and explaining.

[@mdwillington9416]

After removing the old mount, would this provide an opportunity to more easily replace the belt? I’m at 103,000 miles so I’m probably due for changing the belt as well. Thanks 👍🏻

[@americansmark]

I have the rough idle and vibration. Mechanic have me an estimate and told me it was the wishbone mount. He rocked the wheels and the whole thing shook. I’m guessing all three need to go, but I will start with that one and then these if it doesn’t fix it.

[@laywip]

Awesome video, super easy to follow,thanks.

[@dragerboatt]

i have a 2009 ford focus se automatic transmission and i need to change my passenger motor mount but i only have 65000 miles and my bracket is like new. Can i just buy the mount and install it on the bracket or is that to difficult. How would a person go about removing the mount from the bracket and install a new one. Thanks again i love your videos

[@FordTechMakuloco]

Jim B The only mounts that last are the Ford ones linked in the description and those come one way complete with bracket.

[@andrew_neilh]

I’m also curious how you remove the bracket from the old mount and put it on the new one.

[@JeanV1986]

Hi, I've got a question. My passenger engine mount is blown on my MK3 focus (it's leaking) and it's been a couple of months now. I don't get too strong vibration from the engine, but I get some shudder when taking off in 1st gear, but only when the car is hot. Do you think there might be a link there? Thanks for your video.

[@DomKirby]

Man I'm happy I found this video! Thanks!

[@thrillbilly41]

Nice Camera Placement. Thanks for the informative vid

[@postinfinity]

Awesome and straightforward, great job !

[@pmurray8065]

I had Autozone run the parts. They show two passenger side mounts for the 2007 Ford Focus. One called Front Passenger Side Mount and the other Rear Passenger Side Mount. There is also a third mount on Driver's side on the bottom. You are referencing only one Passenger side Mount, AND I see only ONE on my car, and it looks like the one you changed. Can you give a little more insight on this? Good video, by the way; most vids like this are not so good.

[@bjeff1981]

You say to only use Ford mounts, but your link is to an aftermarket part. Reviews say that part has failed for other people shortly after install. Can you clarify? Any advice for sourcing the lower mount?

[@Ny4evr20]

I have a 2011 Ford Fusion with just under 49,000 miles on it. I brought it into Ford service 2 weeks ago when I notice the steering wheel started shaking and the engine sounding like it was racing, and a lot of cracking/squeaking sounds coming from what sounded like the engine. after keeping the car for three days they said they couldn't duplicate the issue I described and told me the suspension/alignment etc basically everything checked out. After a week of having my car back, I was still experiencing the same symptoms, I just dropped it off again yesterday and Kevin my service advisor called and said that they needed to replace the engine and transmission mounts. My question is this, My car has never been in an accident, Is this normal for a 2011 Ford fusion with just 48K+ miles to have both engine and transmission mounts go bad?Thanks for any advice :)P.S. I also notice a funny odor coming from the heater since everything started happening.

[@FordTechMakuloco]

+Rebecca Janke I have seen the right hand mount separate and cause vibration issues yes but yours being so new and of such low mileage I highly doubt it. Is this the 2.5L? At any rate I think they are throwing parts at it at this point only have them replace the right hand mount and be sure to inspect the condition of the lower dogbone mount for wear and or debri grounding it out.

[@Khell23]

thank you for help..car is good now..however, I was too afraid to put 66 ft lbs torque as I felt like I was going to break and lose threading. Will it break? 66 ft lbs is a bit too much. I was turning the torque wrench and still couldnt hear the click . I stopped tightening afraid I was gonna snap it

[@travisclark9906]

Any chance you could elaborate on the “power train/drivetrain mount neutralizing”. Loosen the power train/drivetrain mount fasteners, would that be all the fasteners holding mounts to frame?

[@adriennecurry8094]

thank you for this video I really wish you would have did it aerial view of the components under the hood while the wood was in place because I couldn't see it. you may have tried but the wood was not visible when u panned back. I was only able to see the wood when u showed a close up but I would like to see it from far back so I can get an overall full view

[@427_MAX]

What was the part number to order this mount as a complete part? Using the part fitment guide (link you provided) it only showed me the part with rubber and not the other metal part needed to attach to the frame. I want to remove the old one and replace with new one.

[@mathman1923]

I am needing to do this. How do I know if the other two are bad or is it mostly this one that dies? Nice video

[@FordTechMakuloco]

+Jay Groom The driver side one will completely collapse and be very evident, you will have to remove the air box and other components above depending on year to see. To test the lower anti roll mount just rock the engine and you will see if there is any bushing wear but the passenger side mount is most common.

[@mathman1923]

thanks for the help

[@erl1287]

You must use a FORD OEM Mount. Believe me a knockoff will not work. I’ve tried. I finally shelled out the dough and the car is so quiet. It’s amazing.

[@Blade548]

I'm about to do this job on my Focus and I'm really scared about lifting the engine by the oil pan. Isn't it fragille? I have all the tools and I do a lot of jobs on my car but never changed a mount.I'll try it soon.

[@cookierepairprojects4544]

2010 Fusion I spent all year trying to figure out what I thought was an exhaust leak, hope this will fix it

[@washingtonredskin6574]

Hello good sir. I followed your video for throttle body cleaning and everything went well. But now I have a new problem. The other day i drove over from deep snow, which was hardened. I don't know if that was the cause of this problem or not. Anyway, the problem is excess vibration, on the drivers side when accelerating in reverse. Rolling in reverse is not a problem nor is light acceleration, only reversing and pressing the gas harder causes the noticeable vibration. Driving forward or turning there is no noticeable increase in vibration. Do you think the mount is the problem? And your video only shows one mount. How many mounts in the 09? I think i found the correct part on fordparts is this it? Part No. 6038 Engine Mount Isolator 2.0L Duratec HE (137PS) ; 4-Speed Automatic Transaxle - 4F27E

[@FordTechMakuloco]

Arbys Uunt Meet there are three mounts the one shown, the trans mount and the anti roll restrictor underneath that is the one I would check for the reverse problem. 6038 base does sound right.