How to change / replace the fender / wing on a Ford Focus.
Пікірлер: 39
@FortyCouple3 жыл бұрын
Excellent video. Crisp clear instructions, showing the tools used on each of the less accessible bolts. Nice bit of editing too - never seen the point of watching every turn of the ratchet.
@liztillott62336 жыл бұрын
This video is brilliant! I used it to change the wing on a 2005 Fiesta. It was surprisingly straightforward to do following the instructions in the clip. I have never done anything like this before. Bought a secondhand wing on the net and a set of small sockets to get to the difficult to reach nuts and saved a lot of money. Thank you so much.
@markambrose776 жыл бұрын
yeah, its not too bad, some of the old Fords had them welded on :/
@EnglishLaw3 жыл бұрын
Thank you. Easy to follow at a good pace.
@stephendee78396 жыл бұрын
Clear instruction. Well done. Helped me to remove my fender inner.
@fred_focus_mk1.56 жыл бұрын
Muito Obrigado meu amigo, sempre que tenho que desmontar algo só acho com você mostrando, muito obrigado!
@liztillott62336 жыл бұрын
Someone commented on my post that some old fFords had the wings welded on. Apologies that I accidentally put a 2005 Fiesta when it was actually a 58 plate (2008) an d the newer style Fiesta. The video worked great for this car
@cambs01814 жыл бұрын
I am surprised they haven't been welded on. Ford's of this generation are quite easy to work on.
@everymanforthemself4 жыл бұрын
Nicely done.
@SonorGeek052 жыл бұрын
Will this work for my 2016 Focus hatchback titanium?
@Letham3168 жыл бұрын
Kinda annoyed that it needs so many different bolts removed, but it's good to know that it's not too complicated to detach. Hell, if I have this video at hand, I might be able to do it myself, rather than relying on my mechanic neighbour. Also, I was wanting to learn how to detach the side skirt as I was going to be doing some rear arch rust removal, and I recently learned that the rust will have spread to the metal under the skirt.
@paulmifsud31868 жыл бұрын
thank you very much mark, paul excellent mate
@ScottRods6 жыл бұрын
Thanks, great video.
@williamthomas81355 жыл бұрын
at the 1:50 mark you say "there are 3 bolts "here, here, and here"...yes I see those but two are square plastic not 'bolts" but possibley a shim or adjuster with a tiney screw inside and a tab to push. then you say "you can put the wheel back on" why would you put the wheel on now?
@SuccessfulOzzie9 жыл бұрын
Waw... i need to download this.... I'm going to change that part soon... i don't have the spanners though
@dolly55parton7 жыл бұрын
Thank you Mark for the video I have found it very useful
@international24087 жыл бұрын
Thank you, very helpful.
@MrDuckyJones Жыл бұрын
Currently trying to do this and can't get those 4 screws out for the life of me idk what I am doing wrong
@MrBigwheelman Жыл бұрын
Time for the angle grinder🤓
@alexmawdsley9 жыл бұрын
Valdas, no. The rear "fender" is part of the car. Cutting and welding would have to take place.
@ConleyProduction4 жыл бұрын
Does this work on a 2008 ford focus?
@VarGabi853 жыл бұрын
Thank you!
@wideawake24626 жыл бұрын
Would a mk2 2007 focus front wing be as easy or have they used welding on the 07 model?
@post_low5 жыл бұрын
Idk if you still need this but it's still as easy
@johnnelson50838 жыл бұрын
Would a 2008 focus be about the same? (I hit a deer last night :-( and the passenger fender and hood are a bit crumpled - i was able to drive away though and its not pulling much on the road).
@markambrose778 жыл бұрын
yeah, the 1st and 2nd generation focus should be the same. They look very similar, the headlights go a bit further back and the hood sits a bit higher on the 2nd generation. But should be the same.
@AshotKhooblaryan7 жыл бұрын
Looks like the 2007 focus has something different. Today I tried to take of the front fender as to your video everything goes well, but only one bolt remains which is under that insulation on 0:39 seconds you are showing, but in my focus there is also the whole windshield reservoir placed over there and covering that one bolt and I do not know how to take that reservoir out to rich that bolt. So I do not know what to do now.
@lawilliams33964 жыл бұрын
Thank you.
@Valdasgs9 жыл бұрын
Is it the same process if youi want to change the rear fender ?
@2HED57 жыл бұрын
No such thing as a rear fender. That would be the 1/4 panel which is welded.
@MrBigwheelman Жыл бұрын
Why is everyone calling it a fender ?!!!😬 ... its called a "wing" !!🤷♂️ ..... you're welcome ....😁
@Cheshirebiker929 жыл бұрын
Hi do you know if this is similar to a mk6 escort last model before it changed to focus
@dungareesareforfools7 жыл бұрын
This is very belated, posting it for anyone else's benefit - no, the Escort will be very different, for a start the front wings are spot welded on.
@Bob_at_OZDiggzguitars3 жыл бұрын
You skipped the removal of the Windshield Washer Resevoir and AC lines, now, didn't you ;) kind of important.
@markambrose773 жыл бұрын
Hey Bob, thanks for your comment, from memory you don't need to this. However, willing to be proven wrong (can't remember), are there any videos on KZbin that show this needs to be done?
@titodenino85247 жыл бұрын
Thank you
@TheItalianWays Жыл бұрын
Great video sir I just hit a deer and I hit my right fender. I just missed him about it it’s fucking hit it. I’m so upset only car I have think I’ll be OK if I just try to pull it back a little bit I drove home OK I just wanted to fix a little bit better great video.