Ford Jubilee NAA Tractor Hydraulic Repair: Watch BEFORE Removing Your Top Lid

Рет қаралды 16,343

6 ай бұрын

Parts: farmtractorrepair.com/collect...
Links to videos Rachel mentions:
8N Top Lid Video: • Ford Hydraulic Repair ...
Ford 600/800 Top Lid Video: • How to Repair Ford Hyd...
Ford Piston Pump Rebuild Video: • Ford Tractor Hydraulic...
Ford 3000 Top Lid Video (pivot pin portion at about the 9:30 minute mark): • Ford 2000, 3000, 4000 ...
Follow Rachel on Facebook: www.Facebook.com/tractorrachel
Follow J&D Productions on Instagram: www. janddproductionsinc
The producers of this free tutorial do not assume any responsibility for accidental injury, death or dismemberment resulting from the performance of any orations detailed in this tutorial. Please be aware of common safety steps--expressed, implied or not expressed.

Пікірлер: 34

@tanzerfigueroa1894 4 ай бұрын

Just picked up a 1953 Golden Jubilee, been watching ALL OF YOUR VIDEOS your Daughter is AWESOME and i like her talks to the point, you definitely are blessed ! GREAT JOB TO YOU BOTH

@ditzydoo4378 6 ай бұрын

I did this repair/swap on a 1939 Ford 9N whose hydraulic Piston wouldn't hold much even when operating. Swapped in an NAA Piston with rubber ring/wiper. Holds like Gibraltar now.

@user-qm3ji1yl3q Ай бұрын

This woman is a better mechanic than i am and i have teaes experience And shes beautiful great job to your dad i salute you sir

@blasterstumps7318 3 ай бұрын

You folks are the greatest. Thanks for the videos. One idea I have for a video would be a remote hydraulic setup for the NAA including possibly Hydraulic top link. I can only imagine there are plenty of people like myself that wish they could tilt an implement without getting off the tractor. Anyway, thank you guys for sharing your knowledge.

@hippyhebrewhomestead8593 3 ай бұрын

Just ordered all the stuff to repair the hiccups, nice to have all the parts I needed on one site!

@jdubya54 6 ай бұрын

As usual. Thanks for the great video. I think my 600 needs this so Ill lok for that one. Can tou tell me if you have a video on a 600 series ford on adjusting the governor??

@abuabdallahalutiby5161 4 ай бұрын

Beautiful video and work in mechanical engineering 🌹🌹

@user-lc2tv1dv2e 6 ай бұрын

Another well instructed how to video from a beautiful lady

@GrantJohnston-dr9rt 6 ай бұрын

The talented Tractor girl, well done!

@juanvargas6030 6 ай бұрын

Hello would you all ever consider doing a video for PTO shaft seal and bearing replacement for Ford 3000’s?

@nickfusco740 6 ай бұрын

Thanks. I have a 1963 ford 4 cylinder 2000. Do you sell a video or manual for the hydraulics on it like this or does this also apply to the 2000? BTW all the parts I have bought from you guys, as well as the How To on rewire on ignition-starter-neutral safety switch is perfect.

@wowcreativethings 3 ай бұрын

good job

@chuckb9867 6 ай бұрын

This woman is the bomb

@robertfreitag7328 4 ай бұрын

Just got an NAA. The lift arms raise the brush hog, but drift diwn slowly when tractor is off. Is this as it is supposed to? Great video btw.

@brockdelorenzo7505 3 ай бұрын

Great content. I am very new to farming with some raw land and looking to purchase one of these older Fords. Does anyone recommend a good spot to make sure I don’t get ripped off and or a good broker?

@cropduster2740 6 ай бұрын

As always, very informative.

@ddhogdogs9004 6 ай бұрын

I have a super a the hydraulics are jerking on. Would I need to do this service on it?

@benkanobe7500 2 ай бұрын

Is the seal at 4:42 the "back pressure control seal" as I did not see another one listed?

@charleswinters9721 4 ай бұрын

how to do 8n steering box

@alecfarmer1413 2 ай бұрын

Ford Jubilee 600. Got it for free, and it has a 12v conversion. First start in 8 years; what size battery is recommended?

@50x50mexicano 3 ай бұрын

Where can I buy all the replacement parts

@VmedranoMr 3 ай бұрын

I have coolant in my oil jubilee engine, think it’s a head gasket? It was overheating, water was dropping fast

@bentley1055 6 ай бұрын

Sweet

@Supertramp01 16 күн бұрын

Do you sell the pin that prevents the piston from coming out.. Not sure what its called.. Believe when the piston comes out it hits the pin to keep it from building pressure

@qzorn4440 6 ай бұрын

I like smart people. 🥳 Thanks.

@jeraldhite9744 6 ай бұрын

What do you recommend carburetors wise for my Ford 901 Powermaster. 4 cyclinder gas tractor? Adjustable front axle?

@ShainAndrews 5 ай бұрын

It isn't that easy. There are two or three versions.

@jeraldhite9744 5 ай бұрын

Finding parts has become difficult. The Carb i currently have has one tag on it. So i ordered a rebuild kit off that tag. It was nothing like what i needed. So i used what i could and hand cut gaskets. The float that was sent was was small. So i had to use the old float. So thinking of replacing carb so i can get the tractor running and have a matching carb. @ShainAndrews

@mwsartwell 5 ай бұрын

I took the top lid off without removing the acorn nut, what did I mess up?

@georgemckinney2810 4 ай бұрын

Also wondering about this.

@justinfleenor6882 Ай бұрын

Me too

@user-fk8qz9wj4l 6 ай бұрын

I am a tractor mechanic and lathe technician looking for a job opportunity

@Max-wy2dl 2 ай бұрын

Don't get me wrong, I love your videos, but I recently bought a jubilee, and I feel you could have done better than "go reference these videos".. especially when it's so much different than the 8n 2n 9n setup and in this video you reference ford 600 video. In the beginning of that video you say it doesn't apply to naa or jubilee... Just seems like a lazy excuse of a video if you ask me...