The lamp was fogged up on the inside. The video is of me taking it out and cleaning it. Not shown but worth doing is popping it somewhere warm like the airing cupboard for a few hours to get it thouroughly dried out.
Пікірлер: 73
@Mr_Blinky6 жыл бұрын
Nice, very helpful. I've just bought a mk4 with one smashed fog light and one foggy fog light, so this has helped me loads. Thanks!
@csquire32 жыл бұрын
Helpful video, did mine on the back of this. I would say you have to undo the lower panel (not remove completely) to give better access. As Nigel did, push the headlight back into place and then reconnect it from underneath otherwise it won't sit properly. First one took me 2.5hrs, second one took about half hour.
@bluesilex783 жыл бұрын
Great video, to the point and very informative. I found your video as I searching how to replace both of mine as one is cracked and the other is foggy. After watching your video I will only have to replace one and clean the other. Double bonus thanks!
@brakelee7 жыл бұрын
Thanks mate, i'm now going to try to replace the foglight of my Ford MK4
@stepankozmin59376 жыл бұрын
Helpful information, thanks! Cheers from Czech Republic.
@zathron65724 жыл бұрын
Just an update on my last comment, I did this just now, took an hour or so as the clips to tighten the screws would pop off when putting the casing back in, what I did is bend the shap parts so they dig in the plastic so not to come off. Yet again thank you for the information.
@Q3ToPBuZz7 жыл бұрын
Cheers Nigel, really helpful mate.
@BigDxxxx16 жыл бұрын
Thanks buddy! This was bugging me with mine, very helpful video mate
@garyevans15615 жыл бұрын
Though my Mondeo is the mark 3.This was very helpful. Thanks
@wisienka693 жыл бұрын
Useful in Poland in 2021, thanks
@TheWitusss Жыл бұрын
Thanks for video grettings from Poland
@jesussemenic19606 жыл бұрын
Explicación sencilla y concisa. Muchas gracias desde España.
@chrissmith43656 жыл бұрын
Very good video wanted to do this job for ages was annoying me so much borrowed axle stands difficult to get to bolts though much patients needed looks much better now helpful video
@zathron65724 жыл бұрын
Thank you for information given very helpful.
@hectoraraya62676 жыл бұрын
thanks Nigels, very useful info, best regards , thanks you for your videos, greeting from Norway
@UwagaTramwaj2 жыл бұрын
thanks mate! very helpful!
@vyla25812 жыл бұрын
The Ford Galaxy by 2015m above the fog lamp has only one clamp at the top in the middle of the fog lamp and it is glass.
@royjeffs65384 жыл бұрын
The later mk4 only has one small bolt (8mm). Be mindful if you take the internal bulb holder out that it needs to go back in the same place otherwise you won't be able to replace the light unit back. (The shape of the bulb will prevent it) good video though!
@wiegerink17896 жыл бұрын
And i have another question, i want to lower my Ford mondeo 2.0 TDCI 2008 BA7 with 35 mm in front and 35mm in the back. And i got 19" 225/35/19 tires on it. Is it oké with Standard shock absorbers ? And if that's oké can i put 235 tires on it?
@ziggyzagtv60596 жыл бұрын
hi where can i find the glow plugs on the mondeo titanium 2009 plz can u help
@RickyKennedy016 жыл бұрын
Is it the same for the TXS fog lights?
@marsdencarl893 жыл бұрын
Great vid just a quick question can you get to the headlight washer pump behind the passenger fog light? Need to change mine as its stopped working
@NigelEaland3 жыл бұрын
To get access to the area behind the fog light there is a plastic cover underneath with four screws. I refer to it at the very end of this video when I was trying to reconnect the fog light.
@powerpower17972 жыл бұрын
Good video.
@originalpickaxe6 жыл бұрын
Really helpful . However I have found on my later model MK 4 Mondeo that all though the two screw holes are present only one screw appears to retain the lamp , the smaller hole appears now obsolete.
@mylesmaddux24882 жыл бұрын
I guess Im asking randomly but does any of you know of a way to log back into an Instagram account? I stupidly forgot my login password. I appreciate any assistance you can offer me!
@casekendrick23672 жыл бұрын
@Myles Maddux Instablaster =)
@mylesmaddux24882 жыл бұрын
@Case Kendrick Thanks for your reply. I got to the site through google and Im waiting for the hacking stuff atm. Looks like it's gonna take a while so I will get back to you later when my account password hopefully is recovered.
@mylesmaddux24882 жыл бұрын
@Case Kendrick it did the trick and I actually got access to my account again. Im so happy:D Thanks so much you saved my account :D
@casekendrick23672 жыл бұрын
@Myles Maddux no problem =)
@stevenperhirin6544 Жыл бұрын
Hi, Thanks for your videos. It helps me a lot in the maintenance of my Mondeo. I have a question about the adjustor. What is the best way to access it in order to adjust the fog light? I removed the 4 screws and tried to turn the adjuster by hand, but unsuccessfully.
@NigelEaland Жыл бұрын
To be honest I thought they were fixed but looking at my video again there does seem to be an adjuster. I would suggest you pop out the fog light by loosening the bolts underneath and release the clips along the front top with a knife. I’ve not played with the adjuster but once the light is out you can work out how it works.
@stevenperhirin6544 Жыл бұрын
@@NigelEaland Thanks you for your reply !
@drewby45636 жыл бұрын
Cheers buddy
@drewby45632 жыл бұрын
Hi ! What replacement bulb would you recommend from osram night breaker please...
@josep16324 жыл бұрын
Does the hardware store sell it?
@josep16324 жыл бұрын
I want to ask you what type of screw
@vyla25812 жыл бұрын
how to adjust the fog lights light up?
@MariutaTudor5 жыл бұрын
Hi, can I access the outer left parking sensor by taking out the fog light? It's right above it a few cm away
@NigelEaland5 жыл бұрын
Tudor Mariuta I don’t have sensors in the front so can’t say. I suspect you will need to remove the fog light and then go in via the engine shield underneath.
@adrianmariuta71425 жыл бұрын
@@NigelEaland thanks Nigel!
@wiegerink17896 жыл бұрын
Do you know how to repair a 3rd brakelight of a ford mondeo turnier 2.0 diesel?
@NigelEaland6 жыл бұрын
wiegerink78 no idea but I did find this www.fordownersclub.com/forums/topic/66920-third-brake-light-bulb-change/
@wiegerink17896 жыл бұрын
Thank you, i'll take a look...
@FlorinTofan5 жыл бұрын
what bulb is in use on MK4 fog light? H3 or H8 or what?
@Kalocool5 жыл бұрын
I 'm looking for it too , I think it's H1 same as high beam
@royjeffs65384 жыл бұрын
H11
@97jeki3 жыл бұрын
I got no tools in my studenthouse, could you please tell me which tools are required?
@NigelEaland3 жыл бұрын
Socket set, cross head screwdriver and a knife.
@valentinmihai91374 жыл бұрын
Mondeo MK4 fuse box ? No lights inside car? What can I do ?
@NigelEaland4 жыл бұрын
Check the fuse F17 in the fuse box under the glove box. See my video for the dash camera install. It shows how to get to the fuse box. See also this link knigaproavto.ru/shemy/en/ford/mondeo/478-2007-2014-ford-mondeo-mk4-fuse-box-diagram.html
@paulclifford4469 Жыл бұрын
Does the foglight assembly have to come out just to replace a bulb? Thanks
@NigelEaland Жыл бұрын
Yes I’m afraid so.
@paulclifford4469 Жыл бұрын
@Nigel Ealand thanks Nigel. Looks like it's a bit of a faff. I was going to upgrade to leds but I'll rethink lol. Happy New YeR
@masterrksv3 жыл бұрын
Hi Nigel I checked the bulbs they were fine and the fuses. Can you please tell me what relay covers the front fogs and high beam please. I've checked on the Internet diagrams and the Haynes manual and the fuse box lid there is nothing that says which one is the front fogs and high beam for a Ford Mondeo Titanium not the x. Any help I would appreciate please.
@NigelEaland3 жыл бұрын
This gets a little tricky. You will need to find the passenger compartment fuse box that drops down below and behind the glove box. The lights are controlled by the a control module in this fuse box. In the same passenger fuse box check fuse F13 which feeds the Fog lights. In the engine bay fuse box check fuses F17, F18 and F33. These power the lights control unit and the lighting switch control unit. Have a look at this site to help diagnose workshop-manuals.com/ford/mondeo_2007.5_02.2007/mechanical_repairs/4_electrical/417_lighting/417-01a_exterior_lighting/description_and_operation/diagnosis_and_testing/headlamps/#G939457t35 Next would be to use a ODB2 connector and laptop with Forscan to get the car to tell you what is wrong. See my videos on the CAN system part 2.
@NigelEaland3 жыл бұрын
Just to explain a little more. The lighting system uses the computer network in the car. This network is called CAN. There are no direct wires or relays between the light switches and the bulbs. The light switches connect to the light switch control module and light bulbs connect to the lighting control module. The two modules then communicate with each other over the CAN computer network. If the fuses are intact then the problem is around either of the two modules. The Forscan program is very good at testing the modules and with it you may be able to turn on the lights and prove which of the module is faulty. Unfortunately if you believe it is a module and not a wiring fault you will need to put the car into a Ford dealer as the modules cannot be replaced without the new ones being programmed.
@masterrksv3 жыл бұрын
Hi Nigel, thanks for your help I really need it. There's no light module in The Titanium model only the X model. The lights are all controlled by the BCM. I plugged Forscan in and done a test it said there was an open circuit on the lhs indicator and rhs indicator. Even through they work fine and I've replaced the bulb. I replaced every single relay. I've done a forscan reset on The BCM this does nothing at all. The same faults come back all the time.
@NigelEaland3 жыл бұрын
@@masterrksv Not sure I can help much more. I suggest you follow the test procedures as described. Headlight workshop-manuals.com/ford/mondeo_2007.5_02.2007/mechanical_repairs/4_electrical/417_lighting/417-01a_exterior_lighting/description_and_operation/diagnosis_and_testing/headlamps/#G939457p3 Fog workshop-manuals.com/ford/mondeo_2007.5_02.2007/mechanical_repairs/4_electrical/417_lighting/417-01a_exterior_lighting/description_and_operation/diagnosis_and_testing/fog_lamps/
@masterrksv3 жыл бұрын
Sorted it mate. I went to IPC mode and just changed the settings and wrote it to the module. Thanks for your help mate
@Tahsin_Hussain2 жыл бұрын
I have a Ford Mondeo 2010 Diesel Car? It recently giving me some problem, in UK it's cold now and my car EML is on, it looses power sometime and engine stops. AC take long time to blow hot air. Did fault check and it showed P0116 error code, ENGINE COOLENT TEMPERATURE CIRCUIT RANGE/ PERFORMANCE PROBLEM. Can you tell me where is the ECT Sensor located for 2010 Ford Mondeo MK4 2L Diesel car? Also in summer the car works fine, but in winter it has this problem, is there anything else that can be wrong?
@NigelEaland2 жыл бұрын
This video may be a good guide to where you will find the sensor. kzbin.info/www/bejne/l6XQYqevnc14q5Y I would download Forscan (forscan.org/home.html) to scan the car as it will give you much better information and you will be able to see the ECT sensor signal and see whether it is working or not. My only other thought is whether your thermostat has failed open. Good luck.
@Tahsin_Hussain2 жыл бұрын
@@NigelEaland I already have Forscan in my laptop. Will scan with it later.
@masterrksv3 жыл бұрын
Hi mate, my fog lights and high beam are not working. The lights come on on the dashboard but nothing comes on outside. Can you help please.
@NigelEaland3 жыл бұрын
I know it sounds like an amazing coincidence but the most likely fault is the bulbs have blown. The fog light easily pops out. You will see if the filament has gone.
@masterrksv3 жыл бұрын
Thanks mate
@fernandojovanovic6107 ай бұрын
cool wie du da sitzt😂
@josep16323 жыл бұрын
Can you reply to me? Thank you
@NigelEaland3 жыл бұрын
I’m afraid I don’t know the answer to the type of screw.
@originalpickaxe6 жыл бұрын
Really great tutorial. However by the state of the pinch marks and chaffed skin on your swollen forearm , you've been doing like I do usually learning the hard and painful way on something or another....................
@NigelEaland6 жыл бұрын
Lol. You are so right. I can’t remember what I had been doing but my hands and arms quite often look like that.
@NigelEaland5 жыл бұрын
Check this web site www.autobulbsdirect.co.uk/ford-car-bulbs.html