A well known marketing website? Why not just say eBay and give the site the props it deserves for getting the part you need for you?
@dba61214 күн бұрын
Simple and great. Thank you.
@SimonBrown5 күн бұрын
Thanks
@navigatorjack696910 күн бұрын
Greetings Sir. I was into FTA back in 2010 .I used two sonicview SV-8000hd receivers.One of them has the 8psk module. I pulled them both out of the closet last week and they work fine. Question. Are my two receivers outdated to use today for FTA?
@FreedomMatter11 күн бұрын
How did you fix your ipc failure?u0416 and u0422
@NigelEaland11 күн бұрын
@@FreedomMatter the DTC faults reported were historic from a time I was having battery failure because my starter motor was dying and needed replacing. I reset DTCs and all was good.
@stu-b112 күн бұрын
I shall do mine tomoz before it get too hot cheers matey
@user-yz6iw9ye8w18 күн бұрын
Anyone know if any mk4 mondeo actuator fit?
@andrewpurkis104919 күн бұрын
This video helped a lot. Thanks Nigel
@001eltel19 күн бұрын
Very well explained and easy to follow. Many thanks.
@paulclifford446926 күн бұрын
What car was that on@ MK4 or Mk5
@NigelEaland25 күн бұрын
Mk4
@paulclifford4469Ай бұрын
Hi Nigel can the bulb monitoring system be disabled using forscan? As in I want to fit h7 leds and if they cause a bulb out error I want to be able to disable it. Thanks
@NigelEalandАй бұрын
@@paulclifford4469 not that I know of. Putting LED replacement bulbs in halogen headlights is not road legal. www.autobulbsdirect.co.uk/blog/are-led-headlights-legal-in-the-uk/
@vrummerАй бұрын
Great video. Which website did you order the Mazda spares from?
@vrummerАй бұрын
Nvm, found them from one of your other comments :)
@NigelEalandАй бұрын
@@vrummer www.mx5parts.co.uk/?gad_source=1&gbraid=0AAAAAD_qx0ps9LAktNHbzxDEW8VXIAC2- Thanks for watching. Good luck with your job.
@jimf4748Ай бұрын
Seams very complicated compared to Sky Glass. Connect to Wi-Fi and get every channel perfectly, no matter the weather - it is the future lol.
@jamesredfern999Ай бұрын
You managed to push the piston all the way back before removing the caliper?
@NigelEalandАй бұрын
@@jamesredfern999 Yes I did this time. I used a couple of screwdrivers, one on each pad, to gently lever the pad and piston back. Alternatively take the calliper off and use a G clamp or a piston rewind tool.
@sleeping_sheep_slayer_9000Ай бұрын
great video
@VanadeoАй бұрын
went out today and my calliper was smokin'. So I nursed it up to mi mothers jacked it up and the wheel was solid xD.. Took it all to bits and the gator is just shredded. Sooo I will be replacing it soon. Managed to grease and WD-40 the piston back to life but I know that aint gonna last for ever.
@paulclifford4469Ай бұрын
Hi Nigel I've a similar rattle in my mk5. Seems to be rear passenger door b pillar area. A light metally rattle. I wonder would I have the same issue as yours..
@600GLEАй бұрын
Many thanks for the clear informative guide. I fitted a nextbase kit & mount earlier today following your video step by step. By the way the pull cord on the glove box isn’t for a light switch. It links to the white tube which slows the opening of the glove box. A bit like a soft close toilet seat. 😉 The white cylinder is a kind of tubular bellows (not the Mike Oldfield style). Thanks again. 👍
@NigelEalandАй бұрын
@@600GLE thanks for watching and the info.
@derektalbot4887Ай бұрын
Thanks for that Video, very helpful, but did you need a radio code for SYNC after disconnecting the battery? I am having issues with not being able to remove a previous owners phone, but I was reluctant to disconnect the battery because I cant find a code
@NigelEalandАй бұрын
@@derektalbot4887 funny because I had the same worry and went and spoke to Fords. The radio is hard coded to the car so no problem disconnecting the battery. There’s is no code to input.
@derektalbot4887Ай бұрын
@@NigelEalandlegend, thanks for that, because Ford main dealers couldn’t answer that for me. I have another question if you don’t mind, my cam has an ACC cable, am I right in saying that is in the fuse box under the bonnet? Fuse 23? If so, how would you go about wiring it?
@NigelEalandАй бұрын
@@derektalbot4887 do you mean it has the cigarette lighter style plug to power the camera? If so get a 12v socket and crimp the fuse adapter to it. I did the same thing when I put a camera into our MX5. The fuse box is in the passenger footwell. kzbin.info/www/bejne/aJe8naeEds2boq8si=44XNDrxlwd3bPLd2
@derektalbot4887Ай бұрын
No, it has 3 cables, one is yellow and it goes to the ACC fuse, the purpose of it is to allow the camera to be still recording when parked up, the connection to the ACC fuse ensures that it’s not draining the battery, if it does start to put a drain on it, the camera shuts down
@NigelEalandАй бұрын
@@derektalbot4887 ok I think I understand. Acc yellow is ignition switched supply. Then presumably you have red which is battery +’ve and black which is chassis or battery -‘ve. Everything you need can be got from the passenger footwell fuse box I used. The yellow goes to the 7.5A fuse I used. The black bolt to the nearby metalwork. I’ll have to check my car tomorrow to find a fuse with battery +’ve for the red. Does that sound right?
@StandupukАй бұрын
I think you could have used the old back plate of old programmer. It's the same design.
@NigelEalandАй бұрын
It’s true they were the same but I prefer to use the new one as I had it. No issue then with old contacts in the future.
@kayachan5198Ай бұрын
great video, part 1 too! quick quesiton, do you always jack the car up on 4 jack stands, or is there anything, or is it possible to do everything, with just 1 jack stand? thanks!
@NigelEalandАй бұрын
@@kayachan5198 axle stands are normally bought it pairs and that’s plenty. Most jobs I only use one axle stand beside the trolley Jack. I never trust the trolley Jack when I’m under the car in case it failed. If I need to change say the gearbox oil where I need the car level but jacked up then I use four axle stands. Thanks for watching.
@kayachan5198Ай бұрын
@@NigelEaland thanks for the reply! I was considering trying to save a few pounds and only buying 2 jack stands, but since I want to change all the oils on my mx5 I may aswell take the hit
@paulclifford4469Ай бұрын
Good man Nigel great content. I just purchased my new to me mk5 and ill be doing this very job in the next few days. Have you attempted the headlight bulb replacement? That's gonna be interesting lol
@NigelEalandАй бұрын
Thanks for watching and the comment. Not done headlights yet but imagine they will need taking out of the car just like the Focus.
@paulclifford4469Ай бұрын
@NigelEaland I installed the dash cam today. The fuse you used 29 was live in my car so I ended up using a 5amp at the other end of that line of fuses. I was only thinking afterwards maybe the car hadn't shut down completely. It works good the way I have it. Immediate shut down of camera once ignition off. Bit of a pain getting the door rubber back into position but all good now!
@NigelEalandАй бұрын
@@paulclifford4469 well done.
@abhijitpaul3327Ай бұрын
Press 706 and find out OK
@NigelEalandАй бұрын
@@abhijitpaul3327 I did and didn’t find anything.
@abhijitpaul3327Ай бұрын
0:34
@sirlordbabish3873Ай бұрын
Hi Nigil have you chabge engine on this car?
@NigelEalandАй бұрын
No
@sirlordbabish3873Ай бұрын
@@NigelEaland ok thempk nice video
@ieyoung79Ай бұрын
Thanks Nigel - followed the same steps but for the left rear window and got it working again no worries! Very useful video.
@MrWhothefoxthatАй бұрын
10,000 mile service and 10 years to cover them miles, my oil is changed every march after standing and every 6k after,
@dilla66Ай бұрын
My car is 67 reg. 2 litre diesel manual and worked great thanks
@dilla66Ай бұрын
U are calm and u exsplain things very good cheers mate
@dilla66Ай бұрын
Just done it on my Mondeo took m15 mins to get my head around the video but worked. Great video. Thanks mate. Cheers
@jamieb1367Ай бұрын
put it on usb flash drive not working must have done it wrong can you tell me how its done thanks
@NigelEalandАй бұрын
Check your firmware version compared to the update file to make sure the update is newer. Make sure there is only one update file on the usb at a time. Plug it into the usb port in the console and start the engine. It should start the update automatically as I showed in the video.
@jamieb1367Ай бұрын
can put a photo on here i have put them on usb flash drive i dont no iv i have no iv i dune it wright will let you no thanks
@jamieb1367Ай бұрын
will try and send you a photo
@Simlife101Ай бұрын
I don’t have a programmer only a thermostat can any one help me
@jamieb1367Ай бұрын
my name is jamie you dont no me from scotland glasgow i was watching you video on you tube i have a ford mondeo estate zetec 2017 i have downloaded update extract them 6 i got do i extract them all i am putting them on usb
@NigelEalandАй бұрын
I don’t understand the final part of your question.
@jamesredfern999Ай бұрын
Is fuse 23 coming from the same relay as the 12v power outlets? Did you find any other live switched fuses?
@NigelEalandАй бұрын
There’s plenty of other switched supplies. The fuse I used was convenient and the right type and size for the adapter I had. That fuse box has three different types of fuses. To find a switched feed or even a battery feed I used a volt meter and probed the top of each fuse. F23 is the delayed accessory power. Pretty sure that will be ignition switched.
@jamesredfern999Ай бұрын
@NigelEaland I think 23 is ignition switched but connected to the 12v outlets already in the car. I can't use these as the wiring is fried somewhere after the relay, so need a different feed.
@NigelEalandАй бұрын
@@jamesredfern999 actually I think that fuse gets volts with doors unlocked. I’m afraid I don’t know the answer. Loss of power is most likely a dead relay or blown fuse rather than fried wiring. Good luck.
@peterpokstefl213Ай бұрын
I would need the power supply to be functional even after the vehicle is locked, in order to monitor data from the GPS, is it the same fuse? Thank you
@NigelEalandАй бұрын
No the fuse I used power comes on with ignition. Use F2 or F3 micro fuses which seem to permanent power. fuse-box.info/ford/ford-mondeo-mk5-2015-2019-fuses-and-relays#google_vignette
@peterpokstefl213Ай бұрын
@@NigelEalandThank you for the information, it will probably require removing half of the deck, there is an extremely bad approach. 😬
@anthonyperkins6178Ай бұрын
Does anyone know the socket size needed for the fuel filter housing
@colesthelol2 ай бұрын
Thanks for the instructions. Properly done, unlike the infos provided. The issue I'm having that's stopping me from finishing up is the fact that the long screw seems to be too big and won't fit the hole. I can see that, for you, it went in easy peasy.
@NigelEaland2 ай бұрын
My recollection while filming that job was that I had to redo part of the install where I’d used the wrong screws and washers. We had to work slowly reading the instructions over and over again to get it right. Good luck and thanks for watching.
@colesthelolАй бұрын
@@NigelEaland It was my fault in the end, I didn't notice the correct hole. But all sorted. I even managed to get the spring first try using a long and very thin screwdriver. Cheers, sir! All the best
@NigelEalandАй бұрын
@@colesthelol well done, particularly the spring as that was hard.
@pear78692 ай бұрын
hotdemmit, the part I need.. how to fiddle the cover back over it after installing the spring got skipped :D cheers anyway btw, I didnt remove the center console, just the gear knob and the leather was enough to reach everywhere. might save some time.
@charlie1233702 ай бұрын
Is it the same process on a petrol engine?
@NigelEaland2 ай бұрын
I believe it is similar but not necessarily the same. Check out this link workshop-manuals.com/ford/Mondeo_2007.5_02.2007/fullindex/
@hieuangtrung77952 ай бұрын
great video, thanks you for good quality content
@GBPaddling2 ай бұрын
Great stuff, but would have definitely used 'Copperslip' on some of the pivot points, my CB500x stand became extremely stiff dur to corrosion of the main pivot pin.
@schwinnbiking2 ай бұрын
you dont need to remove any plastic covers to drain oil, there is a service port hole in the plastic
@KukiCreations012 ай бұрын
Thanks heaps this was very helpful
@Daz_Stap2 ай бұрын
You, Sir, have just provided the answer to my problem again. After trying and swearing at my car for over an hour, I watched your video and saw how you got the actuator back into the door, and yes, it worked! Thank you so much for this video.
@willardlewis38872 ай бұрын
Consice and detailed demo, made work simple 👌
@ahmedmahdi41842 ай бұрын
Thanks for useful video in my case the inside locking pins it moving but very little do I have to change the whole electrical module or what
@LHunter2 ай бұрын
Hello! Thanks for sharing it with us. It turns out we got to pay for everything with Apple. And that sucks. I wanted to deploy an app for my colleague and problems began when he said he has an iPhone... That's not a problem, thought I. But after couple of weeks, trying to understand why I cannot debug and deploy iOS apps I give up. Thanks to you, I realised there's no way to do it without paying 99 USD / year, but let's be honest - for 1 app, because most likely I will not use it again what makes whole project really expensive... Have you guys tried to use Apple Developer Membership? Does it work normally? (Like deploying on the Android) Or you had to struggle with unexpected actions again?
@NigelEaland2 ай бұрын
Apple is a pain. I think the $99 is outrageous. Free provisioning only last a week and the app stops working. I’m in the same position I just want to be able to share my app with friends, I don’t want any money. Fortunately I have acquired Apple Developer membership through an organisation I belong to and avoided the fee. Perhaps the next video will be my experience of the options available of uploading through the scheme. I not sure if this is another option. This link was sent to me and I haven’t researched it. www.theverge.com/24100464/altstore-pal-dma-eu-launch-delta-nintendo-emulator-clip-clipboard-manager
@LHunter2 ай бұрын
@@NigelEaland Thanks again! I'll check it out. And I'd be really grateful for showing us what can you do as a member of Apple Developer program.