In this episode we do a LQ9 6.0L LS Swap into a 1992 Ford Ranger with an Ar5 5 speed transmission. The LS engine had a cam swap using an ASA style cam from Summit Racing.
Пікірлер: 91
@toolworkzllc844Ай бұрын
dude used a 91-94 explorer radiator, s10 headers with the passenger header flange moved 2 inches lower and had to smash the back of the firewall back a little.
@thegrumpyoldmillennial3282 жыл бұрын
I have a swapped 92 5sp also! FYI the oil sender on those gauges is a dumby gauge. The sender is a switch, and there is a resistor on the back of the gauge cluster! To make it a real one, remove resistor and use a Ford sender from pre 85 Ford trucks
@Zero2SixtyPerformance2 жыл бұрын
We have the Holley 3.5 screen in the car also so you can see the actual readings digitally as well. Thanks for the tip though!
@safasfgadfva2 жыл бұрын
dope build
@Redrockcab2 жыл бұрын
I've got an 88' Bronco 2 I'm doing the same with but with a manual transmission and Dana 44 axles.
@jackperry93692 жыл бұрын
Bet that thing is SMILES PER GALLON FUN
@chanceireland29422 жыл бұрын
I have a LQ4 6.0 from my 2003 Yukon Denali I just purchased a 1999 Ford Ranger extended cab and 5 speed manual trans it's currently the factory 4 cylinder but I would like to know a list of things I will need to mod and buy to make this swap happen and work correctly. Its going to be my first swap but just was hoping for some good tips and advice. I just want to learn and be able to teach it to my son
@Zero2SixtyPerformance2 жыл бұрын
Idk that I can give you an exact list but in this particular swap we used an ar5 and ict billet accessory brakets.
@andrewgipson32892 жыл бұрын
Very sinister looking. With some Ruugas. What kind of challenge was the using the stock shifter?
@Zero2SixtyPerformance2 жыл бұрын
Nothing a little cutting and welding couldn't take care of. It's the gm transmission with the Ford shifter
@leoney1957 Жыл бұрын
I have a Ranger XLT 2x2 1989, i want to do the same thing or similar, i want a V8 and convert it to manual
@barrymorton91612 жыл бұрын
I'm new here and love what you are doing. Which Holley are you using?
@Zero2SixtyPerformance2 жыл бұрын
Terminator X
@davidsanders112 жыл бұрын
Did you use the factory ranger clutch master cylinder with the ar5? I'm putting a 5.3 with an ar5 in my 93 ranger and trying to find some info on what clutch feed line will work.
@Zero2SixtyPerformance2 жыл бұрын
The factory master has a .75 bore which is capable of actuation the slave. So yes. -3an line
@r3d19112 жыл бұрын
Big question... The motor mounts. I'm currently ls swapping my 2000 2wd ranger and having clearance issues knowing it needs to go higher in the engine bay. Currently using DD 280z mounts and they sit too far down in the engine bay. You have any photos of info on your custom mounts? Please!!!
@Zero2SixtyPerformance2 жыл бұрын
I don't unfortunately
@user-zq3qr4jf8r4 ай бұрын
Nice build bro, what seats are those they look badass
@Zero2SixtyPerformance4 ай бұрын
I have no idea. Never really paid attention to be honest.
@user-mi4rb4vr5g9 ай бұрын
What steering column did you use? I have custom-made my headers on my 98 Ford ranger and I’m not like in the way. It sounds.
@Zero2SixtyPerformance6 ай бұрын
Stock column. I built a new shaft for it from the firewall to box.
@CarlosRodriguez-yx4iq Жыл бұрын
Hey I love what you did with the ranger I have a 79 Monte Carlo with a small block what do you think we can do to it I don't like the 350 trans it has 411 gears in the rear and dual possy where you located at seems like Florida
@Zero2SixtyPerformance Жыл бұрын
St. Petersburg, FL
@eriktulgetske64022 ай бұрын
Hey so I have an 85 fanger I would like to do this to. I may or may not get message back but was wondering about a good cam
@Zero2SixtyPerformance2 ай бұрын
Well there really is no correct answer. There is a plethora of cams out there based on a ton of variables. The Truck Norris cam is very popular, sounds good and works well on a completely stock engine. Hope that helps
@jackperry93692 жыл бұрын
Where u get headers at do u have a parts list for build? I wanna do a ranger short bed stepside any sites for this build on ranger ls swap
@Zero2SixtyPerformance2 жыл бұрын
We built all the parts ourselves
@chrishansen700410 ай бұрын
How well does the ar5 hold up too abuse? Also how does the gearing feel, does it fall out of power on the shifts? Ar5 has some pretty wide gears compared too a t5
@Zero2SixtyPerformance10 ай бұрын
There are plenty of people that abuse the ar5 and have had good luck. I personally thing it would hold up just find for a driver but any sort of application that is going to get abused I just don’t trust it personally. In this application the gear ratios worked out just fine. As far as the t5 goes, I would trust this trans over that thing
@desmondauffrey7823 Жыл бұрын
Hey, looking to put a 5.3 into a ranger here. I've got a 2004r but I think manual would be much more fun. now with this swap what is needed ? I've got a 5.3 out of a 2011 silverado is has a 4l60 4x4 with T case. what do I need to find and buy for it ? if you've got any links it'd be super helpful thanks !
@Zero2SixtyPerformance Жыл бұрын
We built everything custom for this truck so idk how much off the shelf stuff you can buy for it. Ours was also 2wd so you are kind of on your own for the 4wd stuff.
@Dustin-jj5eh2 ай бұрын
I've got a 91 extended cab I want to do this to. Someone point me in the direction of where to start please
@Zero2SixtyPerformance2 ай бұрын
There isn’t really out there as a “kit”. If I remember correctly someone was making the engine mounts at one point. Other than that you are kinda on your own. If you are looking to just drop it off and pick it up complete, feel free to shoot us an email for an estimate - David@zerotosixtyperformance.com
@hunterwilson5670 Жыл бұрын
I'm doing a LS swap to my 92 ranger I would want to know if I can reach out to you and get some pointers where I should start and how I should do it
@Zero2SixtyPerformance Жыл бұрын
David@zerotosixtyperformance.com
@brentrichards12002 жыл бұрын
I'd love to know how much you charge for all this. I have a lifted 93 Ranger with the 2.3, and I think walking is faster. Of course, I would want heater and a/c.
@Zero2SixtyPerformance2 жыл бұрын
This swap was roughly $19k
@tholmes8474 Жыл бұрын
@@Zero2SixtyPerformance dam out of my ballpark lmao
@johnsonbraJ28 күн бұрын
6spd gearbox t6 4x2 can fit 6spd t6 4x2
@chriswise12322 жыл бұрын
Do you think off the shelf headers would have fit if you had relocated the steering shaft exit point on the firewall?
@Zero2SixtyPerformance2 жыл бұрын
Maybe but remaking the shaft was mich easier
@chriswise12322 жыл бұрын
@@Zero2SixtyPerformance I'm fine with a custom shaft, but what I'm asking is if there's any off the shelf headers that would fit if the steering shaft could me moved out of the way. I'd much rather do a column relocation and a custom shaft than a set of diy headers.
@Zero2SixtyPerformance2 жыл бұрын
V8 s10 headers will be close. The problem is the factory shaft has a huge rubber damper on it which will contact the headers.
@BeastV33 Жыл бұрын
Turbo it now
@IdahoFG4 Жыл бұрын
I have a 91 ford ranger 5 speed with the 2.3, I am looking to do the same thing, no a/c or heater too. Could you by chance give me a list of the stuff needed besides the engine and trans
@Zero2SixtyPerformance Жыл бұрын
Shoot me an email, david@zerotosixtyperformance.com
@IdahoFG4 Жыл бұрын
@@Zero2SixtyPerformance I sent an email
@PulpoManiacs Жыл бұрын
How much did it cost to build the hold thing
@Zero2SixtyPerformance Жыл бұрын
Roughly 18k
@BlueDaBos-lu1kb Жыл бұрын
Did you fab your own motor mounts. If not which company did you go with ..
@Zero2SixtyPerformance Жыл бұрын
We fabricated the mounts
@BlueDaBos-lu1kb Жыл бұрын
Ate you making them for order. If not where would you recommend
@houstonrccrawlers64452 жыл бұрын
Ive got a 02 ranger that i wanna do a lq9 or a lt from the 1ss
@Zero2SixtyPerformance2 жыл бұрын
Let's do it!
@daniellittlefield29462 жыл бұрын
How can I get ahold of you brother I want to do this exact swap for my 07 single cab 5 speed
@Zero2SixtyPerformance2 жыл бұрын
David@zerotosixtyperformance.com or 727-346-8919
@reynaldosotelo92402 жыл бұрын
What oil pan are you using?
@Zero2SixtyPerformance2 жыл бұрын
Hummer
@javieraranda2952 Жыл бұрын
Do u keep the original transmission?
@Zero2SixtyPerformance Жыл бұрын
We used an Ar5 transmission
@BeastV33 Жыл бұрын
How much does a build like this cost
@Zero2SixtyPerformance Жыл бұрын
$19k installed
@mamel45 Жыл бұрын
Can the ar5 hold the 400hp?
@Zero2SixtyPerformance Жыл бұрын
Yes. Idk how much I would trust it on something that’s going to get beat on or a heavy vehicle
@mikebauer68652 жыл бұрын
fabulous, no AC? Fl.?
@Zero2SixtyPerformance2 жыл бұрын
No AC. Customer didn't want it.
@mikebauer68652 жыл бұрын
@@Zero2SixtyPerformance oh, well, let me not forget, a Really Righteous ride! Vroom!
@rubenvillalobos15 Жыл бұрын
How did you get it to bleed correctly bro ?
@rubenvillalobos15 Жыл бұрын
The clutch system
@Zero2SixtyPerformance Жыл бұрын
Nothing special. Remote bleeder like any other GM vehicle with the same style release bearing
@jessemendoza14152 жыл бұрын
Where and when can I buy this from you lol 😂
@Zero2SixtyPerformance2 жыл бұрын
Right now. Cmon down!
@jays6.0212 жыл бұрын
Is that a IAT sensor in the intake tube?
@Zero2SixtyPerformance2 жыл бұрын
Yes it is
@jays6.0212 жыл бұрын
@@Zero2SixtyPerformance is there any difference between the plastic one and the one that screws in the intake ?
@Zero2SixtyPerformance2 жыл бұрын
@@jays6.021 No there is not
@jays6.0212 жыл бұрын
@@Zero2SixtyPerformance Thank you it will be my first time using IAT sensor and not MAF
@jacejackson41502 жыл бұрын
How was the driveline set up? What changes did you make to it?
@Zero2SixtyPerformance2 жыл бұрын
Currently stock rear end with ar5 transmission
@seth_ischilln2 жыл бұрын
What rear end are u using
@Zero2SixtyPerformance2 жыл бұрын
Factory rear end for now
@seth_ischilln2 жыл бұрын
@@Zero2SixtyPerformance how much would this cost me if I brought u mine
@Zero2SixtyPerformance2 жыл бұрын
This swap was roughly 18k installed
@brandondickerson50 Жыл бұрын
1988 ford ranger swap lq4 6.o whats all need guy seems l I ke funn plz hellp
@Zero2SixtyPerformance Жыл бұрын
Fabricate mounts. Other than that pretty straightforward
@robertortiz42502 жыл бұрын
What's the ballpark price on a set up just like this in a 98 2wd ranger but with working ac
@Zero2SixtyPerformance2 жыл бұрын
16-18k installed
@earlprice7200 Жыл бұрын
Labor .... What kind of money went into this install?
@Zero2SixtyPerformance Жыл бұрын
7k
@user-mi4rb4vr5g9 ай бұрын
What steering column did you use? I have custom-made my headers on my 98 Ford ranger and I’m not like in the way. It sounds.