Feel free to skip ahead, I feel like the install part is a bit too long. lol Part 1 of my turbo upgrade, turbo swap!
Пікірлер: 81
@Vodafone16v4 жыл бұрын
DAMN!!! That is one clean XT Foz!!! Cheers!!!
@Retro8itmods8 ай бұрын
Don’t you need both clamps for the turbo drain hose?
@leloodallasmultipass7 жыл бұрын
alright alright, you're twisting my arm. I'll turbo up my foz. I'm upgrading the suspension tomorrow. should be a great improvement.
@walmartcop343 жыл бұрын
Do you still have the turbo you removed??
@gunhound45 Жыл бұрын
How do you get cranking without starting it? Do you pull the fuse for the injectors? If so is there any risk of fouling the spark plugs?
@Boofedit2 жыл бұрын
Bought the same dump pipe for mine as it’s same model and year, only issue was mine can’t fit due to my forester being a right hand drive, meaning the steering linkage blocks the ability to fit this upsized dump. Truely gutting. Can’t be done on the right hand drive models, there’s a seperate company that understood this issue here in nz, and they make a slightly smalller version of the pipe, but god damn it sounds no where near as good :(
@jimmynuetron7492 жыл бұрын
Subaru installs turbo silencers on the passenger side fender, remove this turbo silencer and you’ll hear a lot more turbo
@iforc5 жыл бұрын
Cool set up, love those gauges.
@danieljestes82517 жыл бұрын
Nice I was waiting to see what you had ordered after your teaser video! You should seriously do a walk around video and some exhaust clips
@lyannypolanco11413 жыл бұрын
Question, I have an sg5 and got a 20g turbo to install and a 255 walbro fuel pump, should I go more like the one you picked? I have an sti swap but didn’t get a tune yet waiting to put it all together
@abovebeyonddetail2 жыл бұрын
amazing all you have to buy and install for a frigin turbo wow
@unleavenedkaraiteplus34126 жыл бұрын
Sounded like your timing tensioner is was knocking a bit after starting.
@wills53086 жыл бұрын
Hey, any chance you can plug the links of where you got all the products from? :)
@almajaure76523 жыл бұрын
Whould like to see video on your air intake
@torreVs7 жыл бұрын
Primeran! ikusgarria da. Now, all that power under bonnet is going to demand a good lubrication or shorten oil change intervals to avoid oil degradation and future damage to the engine and turbo. An oil with the highest viscosity index will provide thermal stability to lubrication avoiding carbons formations. As comment, if you are using an xW30 oil you can consider Pennzoil Platinum Euro LX 0W30. It has a very high viscosity index 204, in Europe it's sold as Shell Helix Ultra ECT C2/C3 0W30, same Technical Data Sheet (TDS/PDS), same chemistry formulation. Give you a time to know your car on the road with this improvement and I'm looking forward to see the second part. Ondo izan,
@JustaWagon7 жыл бұрын
Thanks man! I run Shell Rotella T6 in the car now, I've been pretty happy with it so far!
@torreVs7 жыл бұрын
+ Just a Wagon ACEA EUROPEAN OIL SEQUENCES www.acea.be/uploads/news_documents/ACEA_European_oil_sequences_2016.pdf Observe the difference (chemistry formulation) between a street/passenger car engine oil and a heavy duty engine oil. One example among others: ASTM D6082 ASTM High Temperature Foam Test. First 100 - nil of foam ml and second 200 - 50 of foam ml (milileters or centimeter cubics) at 150ºC. Where can this temperarute be achieved? Crankshaft bearings due to high pressures. Ondo ibili,
@hennricc-52385 жыл бұрын
Where did you get such a clean car? Was it your grandmas? For real though lol, that tan interior is miiint and that engine bay is spotless!!
@celtic1254348497 жыл бұрын
Use a lighter or heat gun on intercooler piping to turbo for easier install:)
@yamahaSHO7 жыл бұрын
I think it was more of an issue of cutting, testing, and cutting more on the universal hose to fit that presented the pain. :)
@jochizzle7 жыл бұрын
Thanks for the video! This is one of the best ones I've seen as I'm gearing up for VF48 upgrade. Did you drain all coolant before doing this? Not much came out when you put the pan underneath to catch it. Also noticed you detached the oil drain tube underneath the turbo from the block - genius!
@JustaWagon7 жыл бұрын
You don't need to drain all of it, just enough to get the level below the turbo. Not much came out because I didn't open the petcock up very much.
@darkroastlefty28037 жыл бұрын
hi! just found your awesome subie vids! i've not found the answer to this but how long does a typical 2liter 4 cyl turbo last in miles? 100k? 80k? under normal mixed driving... no track nor off roading. Thx!!!
@JustaWagon7 жыл бұрын
Thanks! It really just depends how you take care of it, maintenance and how you drive it.
@te3data5 жыл бұрын
We have examples in sweden running 300k kilometers. Close to 190k miles.
@vergecryptocurrency45526 жыл бұрын
What power gains did you make with this?
@nathanburke55304 жыл бұрын
i know i am late to the party here, But im trying to do the same to my fxt 09 limited but i want to get the trans built up. Any ideas on good kits?
@runforestrun50437 жыл бұрын
Cool! Pretty much my exact setup.
@JustaWagon7 жыл бұрын
Now I just need some driver mod to go with it! lol
@oldsklteg7 жыл бұрын
did you pull a fuse to crank it over without starting?
@JustaWagon7 жыл бұрын
I should have mentioned that in the video, but if you hold the gas to the floor while cranking it puts the car in clear flood mode and cuts fuel and ignition.
@JustaWagon7 жыл бұрын
I should have mentioned that in the video, but if you hold the gas to the floor while cranking it puts the car in clear flood mode and cuts fuel and ignition.
@ricardosalinas49737 жыл бұрын
Just a Wagon it’s that only for xt models?
@theslicks13947 жыл бұрын
How much power are you looking to make with this new turbo? 400-430whp?
@JustaWagon7 жыл бұрын
Something like that. :)
@theslicks13947 жыл бұрын
Very cool. Good luck with it.
@Cybernetichaos665 жыл бұрын
what type of radiator is installed? i own a subu forester 2000 turbo and my overflow tank keeps spilling out water.
@lindseyormsbee Жыл бұрын
You might have the wrong cap on it.
@BAMEFR7 жыл бұрын
what exhaust is that? great video please make more!
@JustaWagon7 жыл бұрын
Thanks! It's an Invidia G200 with an Invidia equal length header.
@q2subzero6 жыл бұрын
Just a Wagon .. i got a cobb downpipe and g200 (04 fxt), but it was waaaaaaaaay too loud! how is yours quiet??
@alexmartineau10604 жыл бұрын
how did you prime the turbo without the car starting?
@JustaWagon4 жыл бұрын
Hold the gas pedal to the floor.
@kabardink7 жыл бұрын
hello! why you use this yellow bottle? for what?
@JustaWagon7 жыл бұрын
Timetunechi To bleed the cooling system.
@oldsklteg7 жыл бұрын
yuss!
@KangarooKid835 жыл бұрын
Are you in Omaha?
@ryanpardue90987 жыл бұрын
Were you running the VF39?
@JustaWagon7 жыл бұрын
Ryan P. VF48
@chadhartley75137 жыл бұрын
dude love your car what was your old turbo?
@JustaWagon7 жыл бұрын
Thanks man! I was running a VF48.
@chadhartley75137 жыл бұрын
Just a Wagon oh dang right now i have a tdo4 with a billet kit in it lol
@FluffyRaT6 жыл бұрын
How's the car going now?
@JustaWagon6 жыл бұрын
I haven't seen the car in about 7 months now, but it's still alive. Can't wait to get back to it!
@darrenankrah67117 жыл бұрын
what gauge pods are you running
@JustaWagon7 жыл бұрын
Darren Ankrah BNA Solutions on top, Subtle Solutions on bottom.
@MarvinDR76 жыл бұрын
What muffler is tha? Can i get the part number please
@JustaWagon6 жыл бұрын
It's an Invidia G200.
@fliaquat7 жыл бұрын
Plz plz fix all the gauges so it sits right. They are all crooked. It's driving me mad lol
@JustaWagon7 жыл бұрын
They're driver oriented :)
@fliaquat7 жыл бұрын
Just a Wagon that's what I figured
@zaclawler4 жыл бұрын
I did not hear any turbo noises.
@JM062446 жыл бұрын
How do you prime a turbo?
@yamahaSHO6 жыл бұрын
Jonathan Montoya Hold throttle to the floor to cut the injectors and crank a few times.
@TheAJCheetah7 жыл бұрын
venting to atmosphere?
@JustaWagon7 жыл бұрын
Full recirc.
@TheAJCheetah7 жыл бұрын
Ahhh ok recirculating into your downpipe? and if so, did you have to modify your downpipe or did you buy it as a kit with the up pipe? I'm doing the same project on a forester too and already bought a SARD downpipe as well as other stuff. don't have the headers and up pipe yet though...I'd rather recirculate it too because I wont feel right dumping into atmosphere but just tryna figure out if i screwed up by buying a downpipe before figuring out my actual set up :/ Thanks AJ A.
@JustaWagon7 жыл бұрын
Ooooh, I thought you were talking about the BPV. My wastegate is VTA, dump tube under downpipe.