Pulley Restoration | Is That Poop??

The old rusty pulley from an old barn does not have many parts, so disassembly was straightforward. In this project I have had to make several bolts new on the lathe, welding, paint spreading, sandblasting, grinding and then some. Please also note that this video is not just to quickly show someone how something works, but also to relax and unwind from the daily grind!
------------------------------------------------------------
▶ What did I do ?! ◀
To disassemble the antique idler pulley it was enough to pull two bolts and disassemble the plain bearing to hold all the parts in my hand. After washing them off in water, I sandblasted all the parts in the sandblasting cabinet. After removing burrs and imperfections, the major components could be painted with rust preventative paint. The bolt, on the old pulley had to be replaced because the old one had too much play in the fit. The bracket, including the bolt that holds the idler pulley, also had to be rebuilt. After all parts were reassembled, the bolt could be filled with grease. As a small detail, the letters were colored to match the pulley.
------------------------------------------------------------
▶ Good to know ◀
I used the following tools: Water pump pliers, pin punch, hammer, dishwasher liquid, brush, screwdriver, wire brush, compressor, sandblasting cabinet, abrasive corundum, key file, metal rust preventive paint, paint brush, lathe, lathe chisel, center drill, drill, cordless screwdriver, saw, tap, center punch, caliper, countersink, polishing machine, polishing paste, multifunctional tool, scriber, parallel scriber, stop angle, angle grinder, welding machine, welding helmet, adhesive tape, lubricating grease
------------------------------------------------------------
▶ Special thanks to my channel members! ◀
------------------------------------------------------------
▶ Do you want to support me? ◀
Do you want to become a channel member? Then you can do it here:
/ @forgottenshinerestora...
You like what you saw and you want to help the channel to develop? If you want to support me, you can donate via Paypal:
www.paypal.com...
------------------------------------------------------------
▶ Did you like it? ◀
Did you like the video?
Then like, subscribe and share it, please!
Thanks a lot!

[@TheGelasiaBlythe]

Turtle's digusted face while looking at the old grease was just classic! The pulley came out wonderfully, and now i am thinking of Hogan's Heroes (Hochstetter). 😊 Such a wonderful job on the old pulley. I hope it has many good years left.

[@ForgottenShineRestoration]

Thank you very much! 😁🐢

[@Fruity_lexia]

My mind went to Major Hochstetter too!

[@davesmith5656]

I like the way he bring the turtle's unique talents into the process. That's the way to treat a valued employee. I just hope he's paying into the social security plan and medicare and is providing for the turtle's old age.

[@TheGelasiaBlythe]

@@davesmith5656 yes, Turtle deserves care in her old age. I think she will never have to worry, though.

[@Luke_ruok]

I really admire your professionalism, care and persistence. I especially like your humorous style.

[@ForgottenShineRestoration]

Thank you very much for your great comment! 🤩 🐢

[@xRavensclaw]

I love the camera filter you used to show the welding! It was neat being able to see more of the welding process up close.

[@ForgottenShineRestoration]

Thank you! 🐢

[@Timknight1946]

It’s not really a restoration, it’s more a rebuild. Loved the workmanship as usual.

[@TheBatman-1989]

Who cares? Bet you're a blast at parties

[@theq86]

I always loved when turtle popped up here and there, but I wasn't much of a fan of his new face in the newer videos until he saw that old grease. You've won me over. Great restoration as always.

[@ForgottenShineRestoration]

🤣👍🐢

[@geneard639]

Not poop, but it may have been a pulley wheel with either a leather or rubber bedding to make the wheel less noisey.

[@Dave_en]

I think its leather or rubber gasket for smooth noise free operation. It's purpose may be to prevent wearing off the pulley and its replaceable component. The leather rotted and appeared to be poop.😂😂😂

[@garymucher4082]

Nice save of that pulley system. And the colors look good too. One suggest, if you have the space, install a backup washer before installing the cotter pins. That way if, or when, the cotter pins spin, it won't scratch up the finish. Thumbs Up!

[@ForgottenShineRestoration]

That's right, thanks for the tip! 🐢

[@GamingWorld-x6j]

I tried alot but didn't found any other restoration youtube channel better than this. You are great

[@ForgottenShineRestoration]

😳🤩 Thank you so much! 🐢

[@JDB-XIVII]

Those colors together… WOW!!! Congrats!

[@ForgottenShineRestoration]

Thank you! 🐢

[@jacquelinelayne7702]

So glad you gave turtle a welding helmet looks good on him.😊

[@ForgottenShineRestoration]

🤣🤣🐢

[@jkkbruno]

the professionalism of the unreal guy, congratulations on your work, I admire you a lot ❤❤🎉

[@ForgottenShineRestoration]

Thank you very much! 🤗🐢

[@terryrogers1025]

Excellent job sir, like the color combinations you picked out, haven’t seen a greasing application like that in years. Thanks for the video.

[@ForgottenShineRestoration]

Thanks! 🐢

[@heathermonks9830]

I love the turtle so much 🥺

[@ForgottenShineRestoration]

😍🐢

[@araidea2771]

Always love watching your videos. Especially after a long day of work ill just watch vid after vid cuz i find them so relaxing ill even doze off.

[@ForgottenShineRestoration]

Thank you 🤩💪🐢

[@JoBeth-os1vd]

What a Gifted Person!!

[@yithanong7593]

Should have had a demonstration of using the pulley.

[@aLuCiNoGeN]

I love that turtle 😍😍😍

[@ForgottenShineRestoration]

😍🐢

[@AyazRestoration]

Great Work Bro well done❤😇

[@ForgottenShineRestoration]

Thank you very much! 🤩 🐢

[@Spicii9896]

I can't believe how well it came apart, sure there were a few times a punch was needed hut for the most part it seemed relatively easy compared to it's condition and how it looked. Great restoration :)

[@Spicii9896]

By the way, I think you should post longer format videos, you obviously work very hard at this and I think more of your work and time should be included, I'd happily watch a 30 minute video of this, you're so skilled

[@ForgottenShineRestoration]

wow, thank you for your great Feedback! 🤩 🐢

[@ameliamosquera2169]

Love the restoration. Ever thought of giving the Lil Turtle a "Spa" day?. He works hard and deserves a shell buff no? Especially after cleaning that S#!T LMAO Great job!

[@ForgottenShineRestoration]

🤣🤣👍 Thank you! 🐢

[@MASI_forging]

Amazing job. It looks so good after renovation. 👍👍

[@ForgottenShineRestoration]

Thanks a lot! 🐢

[@LM77-77]

Amazing restoration, you always put so much effort in and it results in a great end product!

[@ForgottenShineRestoration]

Thank you very much! 🤩 🐢

[@re-fix9678]

good

[@خالدالبيومي-ظ1ز]

So beautiful indeed! Thank you 🙏🏼

[@ForgottenShineRestoration]

Thank you so much! 🐢

[@PerfectRestore]

Great video! I recommend everyone to watch and enjoy the spectacle!!! Good luck, bro!!!

[@ForgottenShineRestoration]

Thank you! 🐢

[@KingYang05]

I’m glad Mr. Turtle understood the importance of wearing PPE.

[@ForgottenShineRestoration]

🤣🤣👍🐢

[@peterbond7357]

Ich als Schweißer musste mir kurz die Augen zu halten 🙈🤭 Kein Phase und falsche Einstellungen bzw zu langsam geschoben beim Schweißen. Trotzallem machst du gute Arbeit. Mach weiter so 👍🏼🙋🏼‍♂️

[@Whitebrowpriest]

Hi, I'm just curious as to why you hand paint the items as opposed to using spray paint? It is an environmental consideration? You know, because of the aerosol emissions from spray paint? Thanks for your answer in advance. 🙂

[@Howiehamster]

I found a easy way to paint raised letters a pice of cloth over a cork from a bottle put the cloth over the cork put paint on the cloth and just dab on the letters I used to do head stones for a living painting the letters so much easier. Hope this helps you out.

[@ForgottenShineRestoration]

Oh thats a helpful tip! thank you very much! 🐢

[@Howiehamster]

@@ForgottenShineRestoration hay you so very welcome and I love what you do keep up the great work and I am from the uk and your the first person who has got back to me for giving tips thank you so very much

[@jurgenk.4780]

Nice restauration

[@ForgottenShineRestoration]

Thank you! 🐢

[@oneshotme]

Excellent restoration and a wonderful job restoring it also!!!! Enjoyed your video and I gave it a Thumbs Up

[@ForgottenShineRestoration]

Thank you very much! 🤩 🐢

[@oneshotme]

@@ForgottenShineRestoration You're very welcome!!

[@nicolasfiore]

The welding part was lovely edited! congrats!!

[@ForgottenShineRestoration]

Thank you very much! 🤩 🐢

[@PZLRESTORATION]

Good job. Congratulations 👏👏👏

[@ForgottenShineRestoration]

Thank you! 🐢

[@1954JDR]

That pulley was once covered by a cow patty. This is a beautiful restoration.

[@ForgottenShineRestoration]

🤣🤣🐢

[@Falatudosobremotos]

Vídeo top demais ❤

[@andrzejporeda7281]

Bardzo świetna jest zrobiona ta robota pozdrawiam twórcę tego filmiku serdecznie 👍👍👍👍

[@ForgottenShineRestoration]

Dziękuję bardzo! 🐢

[@CL-we8tn]

Stunning restoration, more like creation, lol, so glad to see turtle again.

[@ForgottenShineRestoration]

wow, thank you for your great comment! 😁🐢

[@staceysarian7444]

Nicely done

[@ForgottenShineRestoration]

Thank you very much! 🤩 🐢

[@Urantia-1411]

Seus vídeos além de ser interessante é também divertido, me diverti muito com a tartaruga, parabéns

[@ForgottenShineRestoration]

Muito obrigado pelo seu excelente comentário! 🐢🤗

[@MarkuzZz5]

nice welding effect

[@ForgottenShineRestoration]

Thank you! 🤩👍🐢

[@fairwayeichhorn9930]

Beautiful work! And I love turtles welding helmet!

[@ForgottenShineRestoration]

Thank you very much! 🐢 🤣👍

[@sagewas3491]

3:05 Staufferbüchse 🥰🥰👍🏻👍🏻

[@DustinDunn-m9g]

We used these in the Army. Lol. Snatch boxes....😂

[@ForgottenShineRestoration]

😅👍🐢

[@lenux21]

When welding taps like that you should bevel the ends so u get a stronger weld connection and penetration

[@Decora2]

Impresionante!!!😮

[@ForgottenShineRestoration]

Thank you! 🐢

[@thomasliesch412]

Danke sehr schön das Video! Weil auch eine "Deutsche" Erklärung dabei ist! 😀👍

[@ForgottenShineRestoration]

Danke für das Lob! 🐢

[@mskayla7747]

Nicely done! 👍

[@ForgottenShineRestoration]

Thank you! 🐢

[@777MasterHero]

I have two theories as to what that stuff caked in the pulley was: 1. It's manure/dirt from lying on a barn floor for many years 2. It's the disintegrated remains of the rope that use to go around it

[@ForgottenShineRestoration]

I suspect the rope was pulled on the floor (full of poo) and then transported into the pulley...🐢

[@vathraq2727]

I see a similar effect in my work. The pulley starts making noise. They put a lubricant. In this case probably grease. The grease, because it's wet, gathers dirt and dust particles causing it to cake up and dry. Then you have scrape it off to clean the pulley.

[@kumar_ankit28]

That's not a poop IMO. It must be some rubber type thing over a pulley so that the rope is easily pulled without being friction with frame. Rope gets a grip and pull things easily. BDW Amazing work.

[@ForgottenShineRestoration]

This was not rubber. It was poop or mud with straw...🐢

[@kumar_ankit28]

@@ForgottenShineRestoration oh, my bad 😬

[@Ea-Nasir_Copper_Co]

@@ForgottenShineRestoration It might have been asbestos.

[@sugarsammy7209]

I loved how you showed us the welds!

[@Onur19O7]

Thanks for the updated content. 🙂👍🇹🇷

[@christopherdunn7688]

I would rather you restore items, yes old stuff gets wore out and loose. We love your videos and don't expect every item you do to work even better than it did when it was first made.

[@Schlitzauge89]

Good Job, auch wenn ich eher Fan davon mehr der Originalteile zu erhalten. Gerade wenn man Schweiß-, Dreh- und Schleifmöglichkeiten hat. Diese beiden Bolzen (oder Schrauben wie hier jemand meint), hätte man auch so nochmal gerade richten, eventuelle Risse schweißen und mittels Drehschleifung auf Hochglanz bringen können, anstatt die Teile komplett neu zu machen (auch wenn das Ergebnis natürlich gut ist). Für diverse Unebenheiten wäre spachteln eventuell nochmal gut gewesen. Hinter eventuell sprühen, wobei ich Pulverbeschichtung persönlich noch schöner finde. Ansonsten immer wieder schön sowas zu sehen. 👍🏿

[@decoder6379]

Супер.❤ Просто шикарно!

[@ForgottenShineRestoration]

Большое спасибо за ваш приятный комментарий! 🐢

[@vinceianni4026]

Hello mister beautiful restoration good job

[@ForgottenShineRestoration]

Hello 🤗🐢

[@selmamariasantos4775]

Lindo trabalho parabéns 🎉❤

[@ForgottenShineRestoration]

Muito obrigado! 🐢

[@cptea]

What's the measuring/scribing tool used at 11:29 of the video?

[@frick566]

Excellent restoration!!

[@ForgottenShineRestoration]

Thank you very much! 🐢

[@dannyhenson3141]

That turned out very nice. I really like the colors

[@ForgottenShineRestoration]

Thanks a lot! 🐢

[@lucieleimbach]

I’m glad turtle had more of a part in this video. 🐢😊

[@ForgottenShineRestoration]

🤩🐢

[@howardoller443]

2:26 - Whether that is poop or some other substance, when you remove it from the tool, why did you drop it into the wash basin? Wouldn't it have been better, since you had already removed it by hand, to drop into the trash so as not to foul up the water even more?

[@Shae_Sandybanks]

Lol I love your turtle brush 😂

[@ForgottenShineRestoration]

🐢👑❤

[@navy5025]

keep going you’re the best❤

[@ForgottenShineRestoration]

Thank you so much! 🐢

[@garyostrander2507]

WOW = That is some kind of pulley I would love 2 have = SO COOL👍👍 ❤

[@marinamachado4442]

Sensacional 😍

[@ForgottenShineRestoration]

Muito obrigado! 🐢

[@بسامبسام-ه6ث]

Good very good 👏👏🌹🍀🍀

[@ForgottenShineRestoration]

Thank you very much! 🐢

[@TundeEszlari]

Brilliant video.

[@ForgottenShineRestoration]

Thank you very much! 🐢

[@carrestore]

good job Beautiful Restoration 👍

[@ForgottenShineRestoration]

Thanks a lot! 🐢

[@Barych933]

Great job👌

[@ForgottenShineRestoration]

Thank you very much! 🤩 🐢

[@The42Joker]

I loved your welding effect. I don't know if that was a filer, or an after the fact digital edit, but it was the first time I have seen it, and I REALLY liked it! Great job as always!

[@ForgottenShineRestoration]

Thank you very much! 🤩🐢

[@flaviakoch7378]

I said that it was a bicycle😂😂😂. Turtle always safe!

[@transport_restoration]

So nice as usual🎉

[@ForgottenShineRestoration]

Thank you! 🐢

[@strimmerguy]

Good video as always!

[@ForgottenShineRestoration]

Thanks a lot! 🐢

[@stranger7810]

that turtle has literally seen everything after this video 😂😂😂

[@rebekkaholsten4622]

Aaah! Ne Umlenkrolle war das! Die ist ja schon ganz schön massiv! Und juhu, der Sandstrahler 👍 ich liebe das. Und ohne Schildkröte geht ja mal nix 😉 wie viel Arbeitszeit ist da reingewandert? Das Ergebnis kann sich auf jeden Fall sehen lassen, das steht mal fest!

[@ForgottenShineRestoration]

Vielen Dank! In dieses Projekt ist nicht sehr viel Zeit reingeflossen, weil ja der Umbau der Werkstatt immer noch mit zu machen ist 😅🐢

[@rainynight9926]

Pes etme. İsviçre My mechanic kanalını geçersin tebrikler. 👍🙂

[@ЮрийКолесник-р7р]

Уважаю таких людей в ихних руках из мусора привращается в шедевр што не стидно в руки взять и показать друзьям товарищам воо.ще в ассовое обозрение ,оно стоит того ,можно смело дописать "отресставриравано с любововью!"

[@michaelmiles9840]

You have super cool outcomes and always looks fantastic but........the turtle brush thing is one of the creepiest things I've ever seen.

[@ForgottenShineRestoration]

😱😱🐢

[@raikbusse7697]

Bei den Werkzeugen hast du den Schraubstock vergessen, der aus meiner Sicht ein Modell "Baumarkt" zu sein scheint. Vielleicht versuchst du demnächst mal einen alten Schraubstock zu restaurieren. Das Video ist ansonsten super gemacht, ich abonniere.

[@ForgottenShineRestoration]

Vielen Dank und herzlich Willkommen. Der Schraubstock ist auch schon sehr alt und kommt aus der ehemaligen DDR. Ich habe sogar schon zwei Schraubstöcker restauriert 😅🐢

[@MuscoviteDN]

Perfect

[@ForgottenShineRestoration]

Thank you! 🐢

[@tuomaspeltonen090]

What compressor you use?

[@keithfreeman2139]

I liked this one. Good Job. and I just subbed abd liked.

[@ForgottenShineRestoration]

Thank you very much and welcome! 🐢

[@keithfreeman2139]

@@ForgottenShineRestoration I see you also sre able to read bad typing skills. LOL

[@isaacpattie6023]

Turtles face when the lid dropped and made a mess was my reaction too

[@ForgottenShineRestoration]

🤣🤣🐢

[@Tranzisto]

Oh come on, all this great workmanship and not showing us this thing doung even a single rotation. Talk about blue balls

[@guggemamolo]

Hallo, danke für das schöne "ruhige" Video und das du mir und Turtle das Schweißlichtschein ersparst. Warum keine Grundierfarbe verwendet und Gewindeschneiden, des Bolzens, auf der Drehbank. Erlaube mir einen Tipp abzugeben (bei dir nicht nötig da du eine sehr ruhige Hand hast) Sehr feine Linien bzw. Buchstaben kann man schnell und genau mit einem Lackstift zeichnen. Kopfhörer auf und ab wegen der sehr lauten Werbeunterbrechung, geht nicht! Freue mich schon auf das nächste Projekt, dann hoffentlich "größer". Gruß aus Mannheim, BRD, BW Martin

[@ForgottenShineRestoration]

Danke für deine Tipps! Bei der Hammerite Farbe braucht man theoretisch keine Grundierung. Das Gewindeschneiden auf der Drehbank muss ich noch üben, das Absägen hat mir auch nicht gefallen, aber kurz vorher ist mir der Drehmeißel abgebrochen 😅 Grüße ebenfalls aus Deutschland 🐢

[@guggemamolo]

@@ForgottenShineRestoration Hallo erst mal, Hammerlack: habe ich nicht gesehen, klar haste recht! Gewindeschneiden auf der Drehbank, (besonders kleine Innengewinde) voll einfach und super im Lot und Drehmeiselschneide abgebrochen (Mist) aber aus Fehlern lernen (auch wir). Ich denke: Fehler/Pannen ruhig zeigen, Mut zur "Unvollkommenheit" (wenn der Fehler nicht peinlich ist). Danke für die Antwort und bis dann !!! Martin

[@zLrzd]

Bro Op you are my favorite youtuber❤️🙏. I wish you reply to me.

[@ForgottenShineRestoration]

Here is my answer 🤪 Thank you very much! 🐢

[@RakRescue]

Thank the lord Turtle was there to help you

[@raginald7mars408]

This is the pre Historic CPU Fan Cooler from a mega Lithic Stone Computer

[@ForgottenShineRestoration]

🤣🤣🐢

[@raginald7mars408]

@@ForgottenShineRestoration minimum 4 Million $$$$ never sell it for Future Archaeologists

[@noodletribunal9793]

i completely forgot that turtle was a brush lol. hes also more expressive nowadays!(omg his welding helmet)

[@ForgottenShineRestoration]

🤣🤣🐢

[@jlindskog5141]

Super Arbeit hast Du da her geschafft! Prima und die Farben...einmalig 🐢👍🏼😃

[@ForgottenShineRestoration]

Dankeschön! 🤩🐢

[@luizalbertorodrigues4560]

The best

[@imperialpresence1173]

if you ask that question...the answer is almost always yes

[@torvard3854]

А что это за механизм?

[@kelsenellenelvianeverdawn1946]

Barn find? Would explain the gunk.

[@ForgottenShineRestoration]

Thats true... 🐢

[@kelcesar]

3:37 poor turtle 😅 have you ever needed to restore them?

[@ForgottenShineRestoration]

😅👍🐢

[@Cleaning-hz9nt]

سلام داداش من از ویدیو هات خیلی خوشم اومده و چنلتم ساب دارم فقط یک سوال میشه بگه این وسایل رو از کجا میاری که این همه کثیفه و زنگ زده است اگه میشه راهنمایی کن ممنون

[@ForgottenShineRestoration]

سلام من اکثرا از ebay خریدم

[@robertschmidt6383]

With a nice lathe like that why do you not have a cut off cutter? Would be so much faster.

[@ForgottenShineRestoration]

I wanted to cut the bolt on the lathe, unfortunately, just before the lathe ladder is broken off.... 🐢

[@tmjvtxtmjvtx]

4 hrs till I need to get up.....pulley restoration it is!

[@ForgottenShineRestoration]

😅🐢

[@rogerpatrongonzalez5800]

👏👍👏👍👏👍👏👍👏👍👏👍👏👍

[@andreasm481]

Tja bei alten Scheunenfunden muss man schon mit Kuhscheisse rechnen. Ich halte das aber für jahrzehntealten Dreck. Ansonsten wieder sehr gute Arbeit. Mit dem Pinsel arbeite ich nicht, ich nehme generell Farbspray. Wird gleichmäßiger. Und für die Buchstaben gibt es Marker-Stifte, sieht auch besser aus. Viele Grüße an Turtle !

[@ForgottenShineRestoration]

Danke, ja mit dem Pinsel arbeite ich persönlich auch nicht gern. Ich bevorzuge eher einen Farbroller oder ebenfalls Spray. Aber ein bisschen Abwechslung muss ja auch sein... 🐢