Foxtrot-9 Reactor Tutorial (QSERF)

This video will teach you how to operate the Foxtrot-9 Reactor in QSERF, including startup and grid syncing.

[@TheLordOmega777]

Finally someone does tutorial 👏 🙌 😌

[@kajto3595]

here is a quicker tutorial: enable loops and pistons, rise rods till the thing turns green from blue, then get the rods at 45% and there u go, a stable reactor that doesent need any supervision

[@kajto3595]

actually go for 42.5%

[@armchair990]

@@kajto3595 40%

[@GorgoTechnologies]

37.5

[@angellotorres2240]

@@GorgoTechnologies Thank you is stable

[@GorgoTechnologies]

@@angellotorres2240 Np

[@ethandoesthingslol]

Also now there was an update to foxtrot and there's now a note by the syncroscope saying 60hz is actually 40,000 kw on the converters

[@UsernetOhio]

Finally a guy who gets straight to the point and that does not talk for 80 percent of the vid

[@uploads1179]

Just remember the relief valves exist

[@Bewwy_overload]

Bruh this is very different than the DMR, much harder. But tnx

[@ultralaggerREV1]

Fission reactors are difficult to operate than a fusion one

[@ethandoesthingslol]

Temp having the colors: blue, light blue, green , yellow Pressure having the colors : white & red

[@james28gaming25]

where's its located that

[@white_shadow74]

this video was helpful but not quite, me and my friends spent hours trying to sync it, but we can't. and theres nobody who clearly explains it (in videos) can you explain it to me?

[@TheKestrel76]

it's a bit just timing and i think a bit of luck, not more i know past what's in the video

[@kajto3595]

i can help u if u want

[@Maggimoggi]

what do you do when it says high thermal power?

[@Xfoundation123]

I detonated it. Feels good

[@evilboy3521]

Wow somehow I managed to do better the first time I tried this without the tutorial, it didn't even scram first try.

[@captaineli5334]

Hey, just a quick question. How do I disable the safety system?

[@rofli1326]

U need to be a supervisior +

[@jadennelson7886]

when do they hire new supervisiors?

[@aidboo1054]

@@jadennelson7886 extremely rarely

[@blueroblox4939]

its not that bad you can destroy the reactor with the safety sytem on so yeah

[@radiomanreal]

You need to be corporate+

[@Found_footage951]

What can cause a control rod fault? And how do you fix it?

[@TheKestrel76]

random chance i think

[@kajto3595]

@@TheKestrel76 nah i think its not ingame

[@GorgoTechnologies]

im think better use relief valves to stablize reactor

[@Cglynn09]

How do you blow it up

[@TheKestrel76]

Get the pressure up, make sure to not get the neutron flux too high or it'll SCRAM.

[@Cglynn09]

@@TheKestrel76 uh if the pressure gets to high it will scram

[@redacted3930]

Close all valves, raise the rods to 10-20% then when the pressure hits red pull the rods at full speed so the flux goes >8% and there you go alot of alarms will ring and boom

[@Definitely_not_Rylix]

I was so close then the reactor blowed up :D

[@kajto3595]

next time press the scram button when it sounds any alarms

[@Bewwy_overload]

Good job

[@SkooBalls]

@@kajto3595 it automaticly scrams for you unless you turned the safety off

[@Pablex3D]

Safety system: Scram it? Player: No S: Scram it? P: No S: Ok scram it! Fox: Boom

[@radiomanreal]

How to make a fuck ton of power using F9:Put rod select to global, CR speed to 2x and enable continous CR transit, close the relief valves and turn on the pistons, drop the rods 25% (so for example if the rods were at 100% you'd get them to 75% and so on, repeat that until you get to 10% rod insrtion) when its at 10% you want to check the sync thing, if the spinny thing goes counter clockwise then dont turn on the valves (unless high pressure/high thermal power alarm pops up) if its going clockwise then release the relief valves until the spinny thingy is barely moving and its pointing up. After this you can sync the reactor, once its synced change the view to temp. and get the rods to 40% then you want to check the places with the highest temperature using the relief valves you can get the highest temp 820⁰ then you disable continous CR transit and set the rod speed to 1x then you want to quickly get the rods to 35%, when the highest temp reaches 850⁰ set the speed to 2x and get it to 40% again and release the valves to slow the temp rising, when the temp stops rising you shut off the valves and you just keep it stable. Congrats! Youre making a shit ton of power now!

[@nightmare_eyes911]

where is the reactor?

[@TheKestrel76]

-Go to the top of the diagonal elevator -Turn left -Go into the maintenance elevator -Press "3" -Turn left after the elevator arrives

[@nightmare_eyes911]

@@TheKestrel76 thx

[@Toaster914]

Never thought I'd find a murder drones fan in the wild

[@nightmare_eyes911]

@@Toaster914 well you did :)

[@buhar3987]

how do i start it up can u tell it im lazy to watch the video + hard to understand

[@buhar3987]

ik but starting up means connecting to the grid

[@buhar3987]

alr ty

[@ethandoesthingslol]

Fun fact: The temp and pres Button switches the indicators for the rods to a pressure display

[@animations230re2]

Dos this generate energy for the GWh order?

[@hshdthemovie]

if you get more information can u tell me like what exact requirements are for syncing

[@kajto3595]

the meter above the sync button has to be at either -1 0 or 1

[@agentnull5242]

How do you disable safety? It says I'm not authorised to.

[@itzspecialx28]

U need to be admin

[@radiomanreal]

U gotta be corporate+

[@ThRandomGamerReal]

I recently saw someone open a secret door next to the blue button, does anyone know how to open that?

[@light_carrotina2331]

i'm not sure but i think that they were raiders

[@TingFeng77]

the pot at the stairs has a tiny secret button on it, move your camera and mouse around to find it

[@ThRandomGamerReal]

@@TingFeng77 thanks!

[@ThRandomGamerReal]

@@TingFeng77 just checking, at the top or the bottom of the stairs?

[@TingFeng77]

@@ThRandomGamerReal bottom

[@vaneer1335]

when will someone use their actual voice

[@darkheartproductions1616]

What are you talking about dude just has a slight lisp