Minimalist Lathe Stand?

Рет қаралды 17,888

Күн бұрын

Пікірлер: 25

@nickkropat8857 6 жыл бұрын

What a great idea - I love how you used rails instead of a flat surface so the debris can still fall under the machine instead of piling up under the lathe. I need to build a stand for my lathe soon and I will definitely be referencing your design! Thanks!

@HeartlandMakesAndOutdoors 5 жыл бұрын

Nicely done on your Stand, I like it. I built mine a few weeks ago, from a different design, but I can see how this lathe is a little addictive and I can see how a guy would up grade to a bigger version and or have a couple of them in their shop. Thanks for taking the time to make this video and share it with us, nicely done sir. Thanks again and have a blessed week. Dale

@jamesschenken1636 4 жыл бұрын

Because I'm different from you, I would raise the bottom stretcher just a little so my size 15 feet would fit under. Great build and a wonderful idea of the separate rails for support. Thank you for you effort,, your design, and the resulting video. BTW I clicked the subscribe button.

@billmaxwell640 4 жыл бұрын

What a great lathe stand concept. The open rails make so much sense. I’m going to borrow much of your design but I want to incorporate a lower boxed shelf where I can stack concrete sidewalk slabs to increase stand stability. As you mentioned I will probably hang a tool storage cabinet on one end and use heavy duty lockable casters for mobility. ....Banjo Bill soon to be Wood Lathe William

@FranklinWoodWorks2016 4 жыл бұрын

Thanks for the compliment. I currently have 4 80lb bags of concrete stacked on the lower crossmember. It's pretty darn stable.

@pdaunno 5 жыл бұрын

Very nice and probably what I need to build for myself. I have the same Rikon lathe and the same bad back. I've had 2 lower back surgeries over the years. Thanks for the video!

@schechnera 11 ай бұрын

What a great design! I'm going to tweak it a bit for my lathe, but definitely will be building one of these. Thanks!

@e.dbogan6266 6 жыл бұрын

Pretty beefy! Gives me ideas how to build one for myself. Thanks!

@JoePierceMaker 6 жыл бұрын

That's a great lathe stand. I need to build one of these. My lathe currently just sits on an old dresser.

@FranklinWoodWorks2016 6 жыл бұрын

At least you have storage!

@jfsauer42 4 жыл бұрын

I'm glad to see you using the dados and tenons combination. The purists insist that mortise and tenons are the only way to go, but they are loads more trouble to make and much harder to make properly, especially if you don't have a mortising machine. I made two workbenches, both with dado/tenons for the legs and stretchers. Mine are rock solid with no racking at all. I defy anyone to prove to me that my setup is less rigid than a "proper" M&T setup. On another note, have you considered the need for sand bags or other ways to weight up the stand? One benefit of cast iron legs is the stability the extra weight gives.

@SawDustMakerRJM 6 жыл бұрын

Hope to see an update on how well it works for you on your next turning.

@NGinuity 9 ай бұрын

Chiming in from camp thumb cut due to Japanese pull saw. That thing is unforgiving. Opened me right up.

@FranklinWoodWorks2016 9 ай бұрын

You got that right!

@jeffforbes3772 6 жыл бұрын

I agree with E.D below...beefy is right! Thanks for sharing

@duaneshelato3686 4 жыл бұрын

great Video. Your video and sound quality are great. I may be the only hard of hearing woodworker but I can't tell you how many videos that go in the trash before I can get anything out of them because I can't hear them. I am looking for that perfect lathe stand and I'll be using a lot of your ideas.

@FranklinWoodWorks2016 4 жыл бұрын

Thank you for the compliment! I didn't start out all that well because I insisted on putting music in my videos. Many folks complained that they couldn't hear my voice over the music and tool noises. I finally listened, and discovered that all of the commenters were correct. I appreciate you watching and taking the time to comment.

@mikenco 5 жыл бұрын

Yep, I cut a quarter way through my thumb nail with a brand new crosscut hand saw. Completely agree that power tools can be safer. That said, but ONLY when the hand tools are mastered first.

@FranklinWoodWorks2016 5 жыл бұрын

I hear you brother!