Big appreciation and thinks because u the only person who I solve problem thant I'm stuck in in the past couple months Thank you again ❤️
@mdacc1985 Жыл бұрын
Thank You !
@HashimAziz14 күн бұрын
Great work on these tools mate. Is it possible to use this and your similar program for RNS 315 to work in the car, or only via bench?
@mbi-bbpl3 күн бұрын
Only via bench, you have to dissaseble radio.
@radioauto44234 жыл бұрын
thank you
@TheLwd114 жыл бұрын
dzięki !
@ZeitreisenderDrache2 жыл бұрын
Hi I have this problem Open Port OK. Connected at 9600 OK Connected at 115200 OK Bootloader: V E R . 2 . 0 0 Status bytes reading error.
@slawekh78623 жыл бұрын
Cześć. Dzięki za film. Czy wiesz może gdzie potem w samochodzie jest zapisywany "status" lub "kod" radia (nie wiem jak to nazwać) że po odpięciu akumulatora nie trzeba wpisywać do radia Safe Code po raz kolejny?
@mbi-bbpl3 жыл бұрын
W module immobilizera czyli w liczniku, ale nie jestem pewien na 100%.
@krzysztofmakuch5899 Жыл бұрын
Witam, da sie podlaczyc przy pomocy programatora CH341A??
@mbi-bbpl Жыл бұрын
Nigdy nie miałem w ręce tego programatora ale z tego co widzę w internecie to ma on możliwość pracy w trybie konwertera USB to UART, więc powinien działać.
@emanuelferu75193 жыл бұрын
Hi For some reason after pressing Ok button in the tool I get: Open Port OK. SetBaud error.
@mbi-bbpl3 жыл бұрын
It means the software didn't get an answer from MCU, make sure your connection is exactly the same as in help, and did you select correct COM port
@emanuelferu75193 жыл бұрын
@@mbi-bbpl Thanks for the answer. My RCD210 is Technisat ULVWCD 5M0035156 with a blue background display instead of black and the MCU is M306N4FGTGP. So it is a slightly different version. However, I identified the pins in the back of the board as in your video. For the Serial communication in my case RXD1 and TXD1 are routed (I am not sure which one did you use, because there are 3 UART ports 0, 1, 2). The COM port is correct because I used my FTDI for other projects to read/send data. And I see the LED blinking when I click ok, so some commands are send to MCU, but as you said no response back. I already have the code for my radio, but I wanted to try this hack to see if I get the correct code. But it didn't work for me. I read in the MCU datasheet that by putting CNVSS pin to VCC, MCU will enter microprocessor mode and I think this is what you used to read a page in the MCU flash (that contains the code). I also read here: people.redhat.com/dj/m32c/flash-guide.pdf that I need to send an Unlock code to access the MCU Flash. What code did you use? I know quite a lot of MCU programming. So, I could modify the source code to see if I can communicate with my MCU. I was thinking to code the commands in Arduino. But of course if you would share the source code it would save me a lot of time. Otherwise I would most probably drop this hack due to time limitations. Edit1: I also read the EEPROM 24c16. All bits are 0. I guess it doesn't store anything in that EEPROM. Anyway I think the code is stored in the MCU Flash not in EEPROM. Edit2: This is exactly my radio. See pics here: www.digital-kaos.co.uk/forums/showthread.php/495446-Skoda-Radio-code-needed-from-dump-24c16?p=3489700&viewfull=1
@mbi-bbpl3 жыл бұрын
In Technisat RCD210 code is in 24c16. If you read all 0, you did something wrong. I used people.redhat.com/dj/m32c/flash-guide.pdf writing my application. I wrote it in Pascal (Lazarus IDE). For M30879FKAGP in Panasonic RCD210 unlock code is all zeros. I don't share my source code. Regards
@emanuelferu75193 жыл бұрын
@@mbi-bbpl Are you sure the code is in 24c16 for Technisat? Because I am quite sure i read the memory correctly as I have also read the 24c08 eeprom from the front panel and that one has data in it. If i wouldn't have read it correctly then the data should have remained to 0xFF everywhere. I will give one more try later, just to eliminate the case that I placed the clip wrongly.
@emanuelferu75193 жыл бұрын
It is sad to hear that open source in this field is very scarce if not completely unavailable. Everyone wants money for some line of code... Actually you are the only one that gave the executable for free at least. So thanks for that. I believe knowledge should be free to have progress. And nobody will become rich from some from radio hacking. That is just my personal opinion maybe others think differently.
@chuckjuggernaut1662 жыл бұрын
Hi, I diddnt have these same points on PCB, do you know its for ULVWMP3 7N5035156??
@mbi-bbpl2 жыл бұрын
My software is for RCD210 Panasonic only, your radio is Technisat. Code is in 24C16 eeprom.
@chuckjuggernaut1662 жыл бұрын
@@mbi-bbpl ok, i need to read it out? right... have u an video, how to read it?
@mbi-bbpl2 жыл бұрын
@@chuckjuggernaut166 Yes, you have to read it. You'll find videos on KZbin for sure. I don't have one.
@clips52823 жыл бұрын
can you use this to activate aux input on rcd 210 with vcds
@mbi-bbpl3 жыл бұрын
No, to use VCDS you need VCDS interface
@clips52823 жыл бұрын
@@mbi-bbpl will it work on 5M0035156A Panasonic
@mbi-bbpl3 жыл бұрын
@@clips5282 It should work with every RCD210 Panasonic. It doesn't work with RCD210 Technisat.
@clips52823 жыл бұрын
@@mbi-bbpl ok thanks i'll give it a try, is there a way to solder an aux into the radio like this: kzbin.info/www/bejne/h4Wac4iJiphpatU instead of using vcds or a cd changer ?
@siadammm3 жыл бұрын
Helo. Does it work on Windows 10? it does not recognize the port for me
@mbi-bbpl3 жыл бұрын
Yes. It works on Windows 10. Check if your COM port is properly visible in device manager.
@siadammm3 жыл бұрын
I solved it, see the port. However, I got the SetBaud error. I have a "delock" usb to COM port adapter. Could that be the mistake? Thank You!
@mbi-bbpl3 жыл бұрын
@@siadammm This error means the software didn't get an answer from MCU. I don't know what chip is your converter based on. I tested it with FT232 and CP2102 chips. Sometimes you have to try several times by pressing 'read code' button.
@siadammm2 жыл бұрын
This is ok in your opinion? Cp 2102 usb to uart converter module, blue
@siadammm2 жыл бұрын
It have 6 pins: 3.3 v, dtr/rst, 5v, gnd, rxd, txd
@bytcak24102 жыл бұрын
Witam jak zrobic i podpiąć taki programator? mozna info?
@mbi-bbpl2 жыл бұрын
Konwerter USB-UART najlepiej kupić, jak podłączyć; masz schemat na filmie i w programie.
@bytcak24102 жыл бұрын
@@mbi-bbpl dzięki wszysko działa wyśmienicie. PS . u mnie w konwerterze uart zamknietym chinczyk pomylil kolory kabelków txd rxd
@djamshams77563 жыл бұрын
How I can reset safe mode counter
@mbi-bbpl3 жыл бұрын
You can do it by editing 93c76 eeprom
@claudiuionutenache18682 жыл бұрын
You have a video how to edit eeprom?
@florjancveto3292 жыл бұрын
Lp. Naprošam za Codo ,za odklep radia Vw rcd 210.št.VWZAZ1K8647181 Made byTehni Sat UL VW MP3. Lp.in hvala