A black plastic christmas clip with the flat head would hide the screw heads as far as i can see the bolts nuts are for the bracket to fasten to the lower hole on the corner of the lower lip to the factory bumper to pick up the gap to the plastic guard liner then the other hole is for the black screw into the guard liner i could be wrong thats 12:50 into the video the supplier could of given you a couple of C clips to slide over one end of the bracket then you could use matching screws too anyway
@nelc23996 жыл бұрын
U are suppose to use some 3M double side tape along the whole front bumper with the front lip. Then screw them so it won’t flap out
@sir_cornholio54 жыл бұрын
yep I was about to say you could use epoxy as well but really good 3M double-sided tape is some of the strongest in the industry. That would totally work just fine and wouldn't peel off paint in the long run
@stevoalv27323 жыл бұрын
Just installed mine but I used 3M double sided tape to hold down that ledge in the front and on the areas around the fog light. Thanks for all the videos. Its inspiring me to build my 18' XT
@davidhickey86136 жыл бұрын
Why didnt you use 3m double sided tape to secure the rest of the edges?
@haydencheckley48126 жыл бұрын
you should of use 3m tape for a cleaner and better fitment
@JoseHernandez-tz6xl3 жыл бұрын
bayson r has the jdm sti lip, the one you got is oe version.
@TheHumanCarJack3 жыл бұрын
I'll be getting that one next then!
@ryanlefevre974 жыл бұрын
What size drill bit did you use?
@fredericpaquet62984 жыл бұрын
Where did did you find these fog light delete? I love them and i don't find them anywhere!
@Ben-op42o4 жыл бұрын
It's not a delete. The premium trim doesn't come with fog lights, only the touring trim level.
@fredericpaquet62983 жыл бұрын
@@Ben-op42o thanks you for this info man
@hestv67905 жыл бұрын
They do not send this product for turkey istanbul
@Tcby6176 жыл бұрын
what's up human car jack? i have a 14 xt can i do those same mods to my 2014????
@TheHumanCarJack6 жыл бұрын
I think you should be able to
@Tcby6176 жыл бұрын
thanks bro!! i would be down for that forester meet.......
@knguyen2625 жыл бұрын
It's been on about 8 months now? How has it held up for you? (btw, those look like self-tapping screws, hope you didn't drill the holes too big. And never use power tools to tighten small screws)
@TheHumanCarJack5 жыл бұрын
It held perfectly up until last week when I went off the edge of a high sidewalk and clipped off a piece haha
@user-mg2uh8np6c3 жыл бұрын
Instead of screwing it in front part of bumper, try using 3M tapes!!! That is the correct way to do install that front lip!!!
@mattk.52586 жыл бұрын
Just a heads up, this is how you use the rest of the hardware to secure the lip. Fitment on mine was pretty good, not loose at all. It almost stayed on by itself. imgur.com/a/vB2bCX2
@TheHumanCarJack3 жыл бұрын
Never thanked you for this. Appreciate it!
@PRO4XKEV6 жыл бұрын
You ever think about the fog lamp kit.
@TheHumanCarJack6 жыл бұрын
The one by Mishimoto?
@PRO4XKEV6 жыл бұрын
@@TheHumanCarJack OEM accessory, Ebay not bad pricing.
@hestv67905 жыл бұрын
I want your help sending
@PRO4XKEV6 жыл бұрын
use exterior double back tape on the areas that gap some..no more screws..
@TheHumanCarJack6 жыл бұрын
Thanks for the advice but I actually like the riveted look! I've added a few more screws since then and it's sitting very nicely now