Front Wheel Bearing Replacement In Under 5 Minutes (Remove & Install) | Yamaha Raptor 700

[@DUNEATV]

Nice!

[@TheATVWorldVideos]

I know, thanks!!! Once my dad found this way, it's saved us so much time over the years!

[@DUNEATV]

@@TheATVWorldVideos For sure! That’s what KZbin is good for!

[@TheATVWorldVideos]

@@DUNEATV heck yeah! Not just entertaining but a lot of informative stuff out there for sure!

[@ChrisZBr0wn]

5/8in bolt with about 3 inches of non-threaded with the threads cut off did it for me. Worked perfect!

[@TheATVWorldVideos]

Good deal!!

[@QuadriderFMX]

Dude, this is ingenious and literally saved my ass on my 08’ Raptor 250 front bearing removal. Great idea and thanks for sharing! 🍻🤘

[@TheATVWorldVideos]

Glad we could help 😎

[@calebtorres5312]

What type of tires you got on the raptor?

[@TheATVWorldVideos]

GBC XC Masters

[@raptor700dad7]

If we didn’t ride so much , I never would have figured this little trick ! Let’s go for another 4000 miles on the 700 Raptor !!

[@TheATVWorldVideos]

It’s a vicious cycle for sure!

[@Lasersgoespewpew]

What size socket

[@jeffreyhicks9036]

Great video! I may be over thinking this. But you're essentially using the cone spacer to punch out the two bearings? So, you need a bolt that is bigger than the opening on the smaller side?

[@raptor700dad7]

Yes , 2 big to go in but small enough to go in big side , pop small one first then turn over for big bearing !

[@jeffreyhicks9036]

thanks for the reply. update on this, I just used a small socket for the smaller bearing. I used one that was just bigger than the smaller bearing hole. you do end up using the cone spacer as the mechanism to knock the bearing out. and I was worried about the threads of the bolt notching into the spacer. there was no sign of damage on the cone spacer using the socket. hope this helps!

[@sethcarson1339]

What size bolt did you use?

[@TheATVWorldVideos]

I will have to ask him why size bolt, I’m not 100% sure.

[@raptor700dad7]

24mm or 15/16 bolt or use a 1/2 inch ratchet extension, Any will work fine!

[@davidhollyfield9712]

What about the spacer for the back

[@TheATVWorldVideos]

Are you talking about the shaft between the 2 bearing?

[@davidhollyfield9712]

@@TheATVWorldVideos I think they added a spacer I have a spacer on the shaft that the back bearing is against then the one in the middle also one on the outside bearing.. but my quad is a 660 idk if that makes a difference

[@TheATVWorldVideos]

It being a 660 could be the difference since a lot was changed from the 660 to the 700.

[@davidhollyfield9712]

@@TheATVWorldVideos ok thank you for your time

[@raptor700dad7]

FYI Thats the same as 700 , has a little spacer on back then big spacer inside hub then small spacer under nut .

[@doc_teamwaxoffroad]

👍👍👍 #savesportquads #makeatcsgreatagain

[@TheATVWorldVideos]

Heck yeah!

[@kazamo83]

You're not supposed to grease these things?

[@TheATVWorldVideos]

We grease them when we install them, but after installed you can’t grease them.

[@ethanenchilada9341]

I used the old bearing to hammer in the new one but now the old ones too far in for anything to grip onto it to take it out 😅

[@TheATVWorldVideos]

We haven't encountered that issue any of the times we have done this.

[@Banda_okolice]

👍👈👉💪