Understanding Simplify3D - Simplify3D Overview

[@crossthreadaeroindustries8554]

Great video - good thing Simplify3D never gets updated so your video remains useful even 5 years later!

[@oldfarmhand7714]

I cant tell you how much I enjoy your two videos ( so far) it makes it so much easier to understand s3d I will enjoy following along as you produce them. Thanks Again

[@Fugatech3DPrinting]

Glad they helped :)

[@TheGreatMrBill]

Finally someone that talks as fast as me and holds my attention! Thanks for the great overview.

[@Fugatech3DPrinting]

I talked fast to try and make the video as short as I could since I knew it would be long and I didn't want to break it up.

[@cybrsage]

I HATE slow talkers - your talking speed is one of the reasons I can listen to you. :)

[@Fugatech3DPrinting]

Also sometimes I get a bit excited lol

[@lightshadown]

one of the best walkthrou i have seen on simplify3d, seriuosly your video should be the official beginners guide on simplify3d, now i see why my prints where failing so much, and im printing PETG, now they look nice and crispy (note: i have never used simplify3d before, too intimidathing).

[@Fugatech3DPrinting]

Glad it helped!

[@sohaibarif682]

This is very informative video. I learnt alot and enjoy from this video.

[@ericl3272]

does simplofy3d have generic profiles already set for different types of filaments or do you have to make them?

[@Fugatech3DPrinting]

Yes, it has standard profiles for all printers that are in the configuration wizard.

[@jwrtiger]

Nice video introduction of Simplify3D

[@shanewally1537]

Good video! How did you get you units for velocity to be mm/s ? I am stuck with mm/min.

[@Fugatech3DPrinting]

It should be on in the main preferences. Radio button to select mm/m or mm/s.

[@jonnyb44]

Not sure you want to have your fan shut off on the mini. That fan cools the head as well. Could cause filament to melt in the cold end.

[@Fugatech3DPrinting]

You could delay it but I have not had any issues yet. Once I add the E3D hot end I'll only be shutting off the part cooling fan and not the heat break fan.

[@ChinaAl]

Fantastic. Thank you. Now I got a Tevo tornado so are any of my settings different from your? Yes I understand the build size but any of the others? Thanks

[@Fugatech3DPrinting]

I would start with the Tevo Tornado profile in S3D and change things up from there. I like the stock profile except for the support settings.

[@ChinaAl]

Okay thanks much

[@josephschmoberg6778]

very good detailed video, I just bought S3D and I'm learning everything I can ....... Thanks again for the good video. P.S. I subscribed ;- )

[@Fugatech3DPrinting]

Thanks for the sub!

[@Rebel635csi]

Thank you. That was very informative.

[@aos7194]

I've got V4.1.2 and the speed is measured in MM/MIN, not MM/S. How can I change this to MM/S??

[@sinformant]

how does simplify 3d do on recognizing thin walls? I had made a design once that had 0.8 mm walls for lettering and a border and cura would show them in the program but after slicing and putting on the SD card and printing it they didn't print , and what did print was little pieces here and there. I used slic3r and it did fine

[@Fugatech3DPrinting]

It really depends on your settings. I've never really had a problem unless it was with the model itself. If you can, scale the print up 1% and see if it slices better.

[@theGermanPrintingNerd]

Thank you for this Video , I am going throug it slowly so I can correct the s3d I got

[@skyrim4713]

I have a cr_10 using simplify 3d software . my printer print then pause for a couple of seconds then it print pause what am I doing wrong

[@Fugatech3DPrinting]

Sounds like a gcode issue. Have you tried another file?

[@cryingeva]

Im like your explain fast and no bullshit

[@TheMrTape]

What the fuck are you talking about? I had to watch at 2x speed to bother.

[@DyscreteGaming]

nice video.