🌟FULL RINGER CONSTRUCTION DISCLOSURE WITH SCHEMATICS📖

want to buy a ringer or check us out/support us or just browse our vast free archives of ancient electrical engineering knowledge that's listed for free on our patreon? Any support helps in achieving our goal of becoming a small commercial electrical research company that pushes the bounds of what's possible with efficiency & sells exotic generators as well as providing full schematics & being open source.
www.patreon.co...
Greetings Everybody in this video i give exact disclosure of how to construct my modified super joule ringer 3.0 circuit that's modified for negative resistance.
The circuit is constructed on a 6 inch long type 77 metglas laced ferrite rod & all coils take up 4 inches of space & are centered on the rod. The L1 is 26 awg & is 4 inches long. The L2 is 14 awg & is 4 inches long & wound in the opposite direction to the L1 & is bucking. If not bucking the circuit will blow up. What makes this circuit new & unique is we don't use the high frequency output of the circuit directly but instead we send the power into a Negative resistant RLC network composed of three 30k 5 watt carbon film resistors in parallel along with a 1nF ceramic capacitor in parallel that's earth grounded for non linear effects with a cold cathode neon bulb in series to an earth connection of the hot side of the L1 coil. The theory behind its operation is we then tap into the power of the negative resistance non linear RLC circuit wirelessly & resonantly to avoid detuning the primary oscillating circuit & The L3 Tesla coil runs our loads. The L3 coil is wound per tesla patent 336,961 & has three SR560 Schottky diodes installed on it. The L3 coil (s) must be wound in the same direction as the L2. Our goal & theory of operation is to wirelessly tap into the gain of power the negative resistance RLC circuit experiences from the earth ground & the cold cathode neon bulb & other non linear effects. This system when tuned can also super charge batteries due to its high frequency pulsed dc output from the L3 coil (s)
The value of the high quality ceramic capacitor I used in the video to speed up the motor while improving efficiency is a 0.22uF Depending on the motor run you might need to experiment with different capacitor values ranging from 0.15uF to 0.30uF for utmost efficient operation of the motor & I believe Nikola Tesla was using this method to run a motor generator combo to generate ac power at virtually no input power cost once he earth grounded his negative resistant circuitry.
links to other people doing good work
1. • TESLA PATENT + MY CIRC...
2. • The Ringer in Small St...
3. • INVENTOR3 OPEN-SOURCIN...
4. • it is wake up time

[@Advancedbatterytech]

Great video, I know a lot of people share their work but even fewer share the important breakthroughs in their work. Thanks again for the open disclosure. I have seen enough of your work to know that this is an important area the community should now be focused upon. These principles should breathe new life into pulse motor / generator research and the dream of more than a self powering machine that is capable of real useful work. Thanks again for sharing.

[@hrcnlz]

Hello Mtech. I believe that L1 and L2 in your schematic are switched from you real circuit. Thin AWG26 wire goes to base and Earth GND. Thick 14AWG wire goes to collector. Check it! Thanks for the video, sharing the ideas, and specially the effort!

[@nsmtbkid]

Yes, Finally somebody else noticed as well.

[@artturuohola8019]

What this already checked?

[@jimmybrad156]

Would be interesting to hear an AM radio next to it. I guess it's that ~1MHz radio signal that lights up the standalone LED.

[@anthonyjousse3020]

I'm so proud of myself my chicken... I was perhaps one of the first to talk to you about negative resistance a few years ago, you remember, on the towers....and now I see that you are in full in I tell you what you do, the number of times you use it to make people understand lol I'm so proud. you reward me.❤️⚡💫👍😂😂😂😂

[@SuperheroArmorychannel]

Very cool demonstration of the negative resistance effect!

[@jimmybrad156]

Veljko Milkovic's pendulum is interesting in that the output's actions has no effect on the input (meaning one-way only).

[@FaustoGomes]

I noticed the same effects when adding the capacitors to the output of the L3 coil. . I am just so much waiting for the rods i ordered from you. I know you are busy, very busy. . . This video is super clear, anyone can replicate after such a simple and clear video showing everything.

[@csabaargyelan7438]

Hello! Has the trial piece arrived?

[@johanrheeder1640]

Keep up the good work, thanks for a great channel

[@GuardianEngraving]

good on ya mate, hats off to you. Great video.

[@MTECHINDUSTRIES2022]

Thanks :)

[@anthonyjousse3020]

I was talking about it in the comments, guardian engraving he charged you I relaxed it directly, and yes on the one hand most people don't realize... the sacrifice of time spent understanding... and secondly they are lucky that we are altruistic and that we have the value of sharing evolution. big dedication to mtech, to all those who support it who buys or not it doesn't matter we don't have everything you need...💟💟💟big dedication chickens I love you the fight continues

[@overunityresearchchannel]

Thanks for sharing I have been wanting to build this for a while Great work Mtech very much appreciated Excellent video 🙂👍💯

[@shareyourchristmas]

Very good explanation, thanks.

[@blahblahblahblah2933]

What do you think Pat. 336961 is about? In Fig 1., the coil is the field coil in a dynamo. The patent itself is about the use of the auxiliary brush Y. See the paragraph starting at line 10 in the patent text.

[@arunbirla9053]

Remarkable genius.. congratulations for this awesome circuit

[@seychellesroland1399]

THANKS TON BRO. THANKS FOR SHARING.

[@nasaerika1853]

the essence of the switching is that the two coils are switched with direct current at the appropriate frequency by the transistor, and high-voltage pulses come out of the collector output of the transistor, which supplies the cold curren..?

[@jimmybrad156]

Why not have a relay (even if manually operated every x hours) that swaps the supply battery and the load battery, with the load end also having a fixed resistance load (say 30 watts) recorded over several times the total battery energy capacity to prove the over unity?

[@gregstafford2155]

Very interesting but one must compare apples to apples with that motor speed comparison with power supply only then introduce your circuit with the exact same power supply input voltage and compare RPM and power usage efficiency then

[@zenpeak_original]

Take the output, into water! :) You will get bigger energy! Just first time, try out with lower output power!

[@MTECHINDUSTRIES2022]

Very interested to try that

[@MrBademy]

@@MTECHINDUSTRIES2022 eager to see the results, there is a guy on the internet - mad plasmatist, he created a diode that operates in water, and is quite incredible, looks like lightning ball in a jar

[@alanx4121]

Resembles a Chris Sykes partnered output coil that generate energy.

[@dragodv7735]

No it does not.The person with the partenered output coils is a Scam artist.

[@alanx4121]

@@dragodv7735 He seems real enough. Put the setups next to each other, they look the same and probably function similarly too. A group from Romania tried to get him down by generating excess data traffic.

[@Edmorbus]

Thanks for sharing

[@csabaargyelan7438]

Why don't you use a Trigger diode instead of a Neon lamp? It is cheaper, it is also available in the USA, it has the same function. I'm following you from Europe.

[@peterhalleffect2.0]

the yellow coil is wrapped the same direction as the coil under it? yes?

[@jimmybrad156]

It looks like there's 3 pairs of coils for a total of 6? Two yellow, two smaller than the yellow and two smaller again. I only saw notations of the larger 2 pairs / 4 coils.

[@lektor6910]

Thanks for sharing. You are a good one. 🙏 If you now get a looped system somehow it would be awesome. 😊👍

[@Repfuesch]

Has anyone independently replicated this device?

[@paulshields1883]

I'm thinking of building one. Inspection of the schematic tells me it should oscillate as claimed

[@TheGrayHare]

What value was the capacitor that you used when the motor sped up and drew less power?

[@MTECHINDUSTRIES2022]

0.22uF

[@piereduplessis4544]

combine it with a joule thief circuit?

[@devinmccloud]

I think jj thomson was the one who copied Teslas coils and brought them back to the UK.

[@MrBademy]

lol thanks man

[@mykedoes4099]

7:15 similar to the Vortex POE config

[@mykedoes4099]

👍 (Circuit Diagram)

[@quantumenergysolutions9128]

Can you see what will happen if you put opposite Neo Magnets at each end of the ferrite rod?

[@ardiwork]

👍⭐

[@dinohj]

First of all great work! And thank you so much!. Did you do any frequency measurements on this circuit? Maybe hook up a oscilloscope? Was wondering in what frequency range the ringer operates optimally.

[@MTECHINDUSTRIES2022]

Around 1mhz :)

[@jensbuchholz5766]

❤

[@quantumenergysolutions9128]

Mate can I assume you have Patrick Kelly's PDF file?

[@MTECHINDUSTRIES2022]

@quantumenergysolutions9128 yes, I've got a library of pdf files that I listen to using speech to audio software :)

[@davidrichard1744]

Three 30k resistors in parallel will result in a combined resistance of 10k

[@MTECHINDUSTRIES2022]

@davidrichard1744 yes, with 1nF ceramic capacitor in parallel :)

[@warrenstephens8557]

Well then fix your schematic

[@jacekwis512]

Hello, I am from Poland, I am over 40 years old. How can I increase the higher voltage and amperage. How can I increase the power of the device? The second question is at the output of your device system what is the voltage and amperage? When I calculate the energy in resonance, it should be high voltage and amperage. I do not have anyone who would tell me how to increase the power of the device.

[@Waveit5]

Hello. I sent you an email regarding my last order from 5 months ago... which payment has already been made. please would you like to clarify the status? I haven't gotten any response from you or any package yet. THANKS.

[@anthonyjousse3020]

Traduire du texte avec votre appareil photo no because in fact they all think that we have assholes, but no we don't have a hell of a phenomenon, don't forget the whipping boy, anu... a very brilliant guy too, makes the others laugh. .. to detect a voltage, neon bulbs must be used like on extension cords haha

[@anthonyjousse3020]

❤❤❤❤❤❤❤😂❤

[@bitkoinpapa]

interrest effect with magnet ......why you didnt try to put it on both sides of ferrite rod maybe it will increase much more effects

[@MTECHINDUSTRIES2022]

I have & the magnet only increases the output power on one side which is very interesting at no extra input power cost

[@themaneman2938]

@@MTECHINDUSTRIES2022 but in yor video at 25:46 we see that with the magnet the amp is now close to 1amp and without is about 0.5 amp...yes it drop when connecting load but on "stby" mode is taking more power.

[@themaneman2938]

@@MTECHINDUSTRIES2022 and great video by the way as always! 🙂

[@anthonyjousse3020]

This guys IS m'y friend... Veery brilliant comme Never ♥️💟💟💟⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡⚡🤓🤓🤓🤓🤓