Furitek Brushless Stinger Kit for Axial AX24! How to Install and speed comparison

Checking out the new brushless kit from Furitek to transform your AxX24 into a snail!
I finally have Merch!!
Be sure to check the sizing chart and maybe size up on those Hoodies.
Check it out at the website below!!
2fm-rc-shop.fo...
Furitek Stinger Available here
furitek.com/pr...
Scx24 Screw kit found here
amzn.to/3Tzgbov
Super wheels found here
hardparkrc.com...
OGRC pin tires used on super wheels found here
www.amazon.com...
Don’t forget 2fmrc at checkout for discounts at most of your favorite shops!!
HELP SUPPORT the channel by clicking my affiliate links below and then shopping at no extra cost to you!
Thanks for any help!
AFFILIATE LINKS BELOW
Horizon Hobby affiliate link
bit.ly/3eXihxY
Amainhobbies affiliate link
bit.ly/3CurIyF
FairRc affiliate link here
shrsl.com/3qxuc
FMS Affiliate link here
www.fmshobby.c...
Amazon affiliate link
amzn.to/3I4tQzI
RCAWD affiliate link here
rcawd.com/?ref...
Other DISCOUNT CODES BELOW
FMS discount code is 2fmrc
$10 discount is only applicable to the purchase of complete all vehicles and accessories, and can only be used when the amount is over $50
Injora Discount code is 2fmrc05 for 5% off
MofoRC discount code is 2fmrc
Fullsendrc discount code is 2fmrc
RcAWD discount code is 2fmrcawd5 for 5% off
Micro Komodo with mount for Trx4m here
furitek.com/pr...
Furitek stinger combo for TRX4M here
furitek.com/pr...
Furitek lizard ultimate here
furitek.com/se...
Order from FMS site and use 2FMRC discount code $10 off complete truck purchase here
www.fmshobby.c...
Extended links for the fcx24 found here
Link kit available here
www.ebay.com/i...
Contact me at [e-mail]
Purchase PARTS for the Fcx24 or rtr and help support the channel here!
shrsl.com/3la45
FCX24 Portal Gears included in this set
shrsl.com/3la70
FCX24 at amainhobbies here!!!
bit.ly/3yoLwRL
Fcx24 on amazon here!
amzn.to/3nDSCfb
High clearance links used found here
amzn.to/3NfOJaj
RC4WD Stamped steel Wheels used found here
bit.ly/3ntbRbc
RC4WD Scramblers found here
bit.ly/3FT3GgA
Other upgrades found here
Injora brass wheel rings found here
amzn.to/3zVGWM1
Wheel hex extenders used found here
amzn.to/3Oh8FLy
Stock Scx24 driveshaft (long) used for rear
amzn.to/3ndGhOk
FMS FCX24 available here in yellow
amzn.to/39OSMwU
FMS FCX24 available here in blue
amzn.to/3HHAHgJ
FMS FCX24 available here in red
amzn.to/3Oyjvwd
TOOLS I USE FOUND HERE
T-handle wheel wrench I use here
bit.ly/3qst079
WORK MAT I USE FOUND HERE
amzn.to/39gcXUb
MIP .050 hex found here
bit.ly/3xOvi45
MY FAVORITE TIRES BELOW
Injora 64mm Hyrax
amzn.to/3fmOShr
Power Hobby Trail Warriors found here
www.powerhobby...
Rc4wd Scramblers
bit.ly/3FT3GgA
MY FAVORITE ELECTRONICS BELOW
My favorite SERVO for the price (agfrc)
amzn.to/3xJbb7r
Another great BUDGET servo here (Emax)
bit.ly/2SjZXUx
My favorite ESC found here
bit.ly/39jhrtc
My favorite BRUSHLESS motor here
bit.ly/3MIMEU3
My favorite BRUSHED motor here
www.ebay.com/i...
~-~~-~~~-~~-~
Please watch: "Injora Lights for SCX6! Super Bright & CHEAP!"
• Injora Lights for SCX6...
~-~~-~~~-~~-~

[@mzondi1970]

New sub here. Im 53 and battling cancer. I've been away from the hobby for 30 years and bought one of these little crawlers I love the information you've been giving

[@2fmrc]

That’s awesome you got back into the hobby after so long! Really appreciate the sub and comment. Let me know if ya need anything!

[@mikellewis2346]

Best of luck on your fight.

[@xXDaReasonXx]

I literally commented on their post on fb about this motor saying, "awesome always the best, now make it CHEAPER!"

[@draken4936]

My stock one had not nearly as bad slow crawl as yours, must’ve got a good one

[@wingnutbert9685]

Good thing you had access to get that busted screw out!!! I'm really starting to think having a few tap and dies on hand, in the usual sizes for these might be a good idea. Just to quickly run through the screw holes and over the screw threads. Not all breaks are possible to remove and that can be a heartbreak if its a pricey part you waited months to get. So hard to see and/or feel when these little tooth pick size fasteners are binding or cross-threaded.

[@sebo-Kids-RC]

You know, you could use the Spektrum SLR300 receiver to get rid of the stock ESC... will bind with the stock Transmitter and 4WS will be the same... Nice done with the brushless ❤

[@2fmrc]

Yeah I honestly just ditch the stock receiver/esc altogether myself and go with a micro receiver for my flysky. Just wanted to show how this works with the stock stuff for the vid.

[@keatonjorgensen8793]

Furitek needs to come out with more rtr or complete cars like the cayman.

[@ajaxrc]

Haha they listened

[@andrewrichey7374]

Super cool oh I like it, Yep I’m here watching

[@nickhathaway4617]

Wanted a furitek for sooo long finally was able to do it got the Stella transmission with the mini and when I ordered the ESC I ordered the V2 instead of the pro didn't realize it until I tried to mess with the settings. So mad but still an awesome ESC and I don't ever plan on running 3s anyways. But just the point for the extra 10 more dollars I could have got the pro

[@2fmrc]

Dang! Yeah that does suck but it’s still a really good esc.

[@nickhathaway4617]

@@2fmrc no complaints 👌 it's incredible but that thought of its technology not as good 😆 although I could probably never tell the difference I was happy as a pig in s*** until I realized I screwed up lol

[@jimblu86]

Good vid. I got an ax24 and 1st thing i did was throw it on an angled board and get a baseline for how many degrees it takes to flop in every direction. Well, after 5 min of driving, the nut for one of the top links fell off and i cant find a replacement. What size is it? Lhs's have no idea and cant help me. Do you know? Lol

[@2fmrc]

Thanks! I think you may be talking about the tiny 1.4mm nuts. MofoRC has them here www.moforc.com/products/teeny-tiny-nuts-precision-stainless-steel-1-4mm-stock-scx24-screw-size-pitch-nuts-sold-in-10-pack

[@gibsonlife573]

With the bigger Rim it don't leave much Tire left for any type of Squish wraparound nothing it don't look like it does it not to me anyway just a observation

[@josephlawrence6873]

Just curious are you going to be doing a video in the new rochobby Magnum?

[@2fmrc]

Already did!

[@josephlawrence6873]

Yeah I watched it last night bummer you got a bad servo...

[@robertkirchoff9407]

what is a good 3S battery to run in SCX/FCX 24's?

[@2fmrc]

Palmbeachbots.com has some great tiny lipos.

[@anon556]

So if you upgrade to the new ESC and swap to a new receiver instea dof using passthrough do you retain all the functionality of the 4ws system?

[@2fmrc]

You would just set up the rear steer for a channel on your new transmitter. So it depends what transmitter you’re using really. When I swap to the flysky gt5 for example I put my rear steer on the ch5 knob usually.

[@nolanhunt2011]

First

[@cornfieldcrawlers9907]

Every time I see anything on an AX24 I just think about how odd of a design it is. It looks like it should be a MOA. Appears to be difficult to mod without just hacking it into basically a flat rail chassis. Compared to what FMS & affiliates are putting out Axial is looking like they are falling far behind.

[@DoubleADay]

I'm waiting for a chassis delete kit and then I may go this route. Have you heard of anything yet for the ax24 chassis?

[@2fmrc]

I know of 1 in the works 🤘

[@hpnc81]

@doubleaday is there a chassis delete kit already available or in the works from somewhere?

[@troypostie1252]

The SS DEMENTOR Is the delete kit Aaron.😂😂😂

[@kez850]

@@2fmrc 🙏 patiently waiting

[@aaronscott2278]

Wow amazing great video !!!

[@ClevelandRips]

I’ve been thinking about putting one of these motors in!

[@boredom.victim]

those donk rims actually look cool, 👀

[@davidzimmerman2478]

Go Anywhere, Go Axial !!!

[@rctony710]

Hi u obviously have the best channel for scx24 keep the content coming. Ive been gone from the hobby for about 1 year now. I have 4 heavily modded scx24s And i was wondering is it worth getting a asx24? Is thwr a big difference ?what are your thoughts what can itvdo that the scx cant?

[@gibsonlife573]

Lol thanks Matt

[@waltersmithat70]

I installed the ingora electronics for like 35 bucks and mine runs just as smooth as what you have there for less than a quarter of the price you paid

[@ChiefRickyRC]

You got heck of a SCX24 fleet wow! I just put a 2430 motor in one and its so beast you should try it

[@nate4024]

Yea the price is outta control on 24 upgrades lately. I just got a hobby wing fusion pro 2in1 for 140. And got the furitek lizard pro mini komodo with stellar trans for 150. I kinda gave up on 24s for now just cause prices for parts for now sticking with the big boys for summer come back to 24s in winter lol

[@gibsonlife573]

It's the way I would recommend to do the sliders also because they can be a pain in the ass trying to make sure they set they're just right by you get this screw through

[@jstro-hobbytech]

That's awesome. I have enough upgrades to basically change every part but I might as well wait until the ogrc arrives and do the similar upgrade to what you just done then add the other parts to add weight to it. I find it too light now which makes it top heavy. I have a small receiver and should switch that out now. Along with the injora links, axles. My tires I have that are after market all seem too small compared to stock. What brand 3s is good for the 24's? I got a pair in today that I thought would be small enough but they are way too big.

[@MetrologyEngineer]

Does it grind your driveshaft when you bottom it out?

[@watsonira7]

Furitek is very specific on only fitting the stock transmission. Well my ear came off and I need a new transmission housing. I'd like to get something better than stock but still fit the brushless system. Any ideas ?

[@ujeanmack3716]

Hey Buddy, just got the ax24 and the torque lean is annoying. It’s still stock. How can I limit the torque lean?

[@shawnrichardson118]

Great video I definitely know what my next upgrade will be thanks

[@brentfoxhoven]

I just bought and installed a Komodo a couple weeks ago. I really wish I would have known the stinger was a thing. Looks like the center of gravity is much lower 😫

[@AgeOrmstad]

Sweet video 👌

[@gibsonlife573]

Wow a break down o mam thank you were going places

[@kez850]

How long did it take you to get your order from them? Seems like it’s going to take 2 months at this rate 😂

[@RichB07]

That's cool . Look's similar to my moa super crawler . has that look with those wheels

[@backyardmowerracing492]

I can’t get mine to connect. Steering works but motor won’t turn

[@johnlujan8706]

Excellent video! I definitely would like to go brushless on my Deadbolt.

[@travisyork3915]

Drag brake adjustment as well to stick 😊

[@burakeren]

I saw some posts about motor hitting driveshaft especially when chasis is lowered. Have you had any issues like that?

[@2fmrc]

Yeah you really gotta watch that on the ax24. I usually make some links and extend mine a bit to help.

[@mikemangiameli561]

What type of 3d printer do you have?

[@2fmrc]

I have an Ender 3 V2, an Ender 3 S1 and an anycubic mono x 6k resin printer.

[@mikemangiameli561]

@@2fmrc wow

[@broken4999]

Does this setup give it a drag brake?

[@2fmrc]

With the Furitek app you can adjust the drag brake. The worm gears of the scx/ax24 gives tons of drag already though.

[@broken4999]

Thanks man appreciate it

[@jstro-hobbytech]

I just ordered the ogrc bldc and gear box

[@Hannsom7]

how do i get them big rims and tires lol

[@2fmrc]

Hard Park Rc 1.8 wheels and ogrc tires. Gotta cut the tires to fit the wheels. www.amazon.com/dp/B0BNVFCCBX/ref=cm_sw_r_as_gl_api_gl_i_2J3QYYTVENB149H7GB4B?linkCode=ml1&tag=2fmrc-20

[@2fmrc]

hardparkrc.com/collections/super-wheels

[@Papa_Shorty]

Although I see potential in this rig, it seem it requires so much more to getting working decent. From throttle to the rear steering. It’s a tough sell for me.

[@kez850]

That’s the rc hobby for you. Hardly any cars come with proper upgrades. Most of them are begging for new parts 😅

[@matthewcopeland4441]

As always good video! Hard part for me is just the cost: $280 in total for a great slow crawl 24 with no weight down low and stock tires and servos. I know people dump crazy money in them, just sharing my take.

[@2fmrc]

Yeah I totally agree!

[@chaoscarl8414]

I was having similar thoughts. Been looking at getting into some rock crawling / bashing, and looked at this car because I like the smaller size and somewhat reasonable price. But with what looks like "minimum requirement mods" to get a decent crawler out of it, the price starts going up really fast. I mean... This Furitek set is almost as much as the car itself... I'm honestly starting to wonder if paying a bit more for a 1/10 car would be better in the long run as you'd be starting out with a more capable platform? But dang... These minicars are cute...

[@VetteWay2Fast]

Only thing with 10th scale crawlers or models in general is space and areas to run. The micros can be run in the garage or living room and one can build some good, lightweight and portable courses with liquid expanding foam for rocks. Finding good crawl areas for bigger models is trickier and usually requires traveling from home.

[@FailedSquare]

annoying that furitek links this video for instructions and its 5 solid minutes of this dude yacking before he starts the install and then the install process itself is sped up to mach 3. I JUST WANNA PLAY WITH MY TOY TRUCK

[@2fmrc]

😆 then you better get to work! So I shouldn’t even show how it’s an improvement? Just let people take my word for it? I’m not like these other channels that just tell you to go buy it because they got it for free. I try to show the improvements as well. The install is as easy as cutting cake. You spent half the amount of time it takes to install typing the comment. Just go for it!

[@FailedSquare]

@@2fmrc it was a criticism of furitek for being lazy and relying on someone else to create an instructional video.

[@2fmrc]

@@FailedSquare ahhh I get it. I normally don’t even do any install stuff just because if I don’t speed it up it sometimes gets boring. But yeah they should probably do a full install vid or at least ask someone else to lol

[@ericwagner3223]

Great video! Would love a video on the Bluetooth and how you set up your throttle curves and punch settings.

[@2fmrc]

I rarely ever adjust them lol

[@wingnutbert9685]

I know you've mentioned not liking watching build vid's and I'm sure they are a lot more work to produce. ut, you did a real nice job filming and voicing this vid. 👍👍👍👍👍

[@troypostie1252]

Nice grab Matt. For once in my life I'm ahead of ya on the SS build. Your normally ahead of me by months😂. Check out the Akkers 1.9s shhh don't tell everyone 😂😂👍🤠👍

[@2fmrc]

Lol I been trying to chill on vids and builds lately. Get a little burnt out. I seen those wheels on Facebook. Look sharp!

[@CWxGOONxWC]

I need to know where I can find that bug body

[@2fmrc]

Team blue groove. They say their shop is closed atm so they aren’t taking orders but they are sometimes on eBay also. Just search 1/24 bug body. teambluegroove.com/collections/1-25

[@CWxGOONxWC]

​@2fmrc709 thank you great video

[@ericmyers1306]

holy crap! amazing difference!

[@nouse4aname_]

It's all "really nice"..😃

[@2fmrc]

Lol I noticed that. Crazy the things you start saying in some of the vids. Not going back to redo it though 😆

[@nouse4aname_]

@@2fmrc no worries and don't sweat it. It makes for entertaining content. Don't change a thing bro.

[@jeffmackovitch9987]

I’m glad that outboard motor doesn’t rub since it’s so tight on that AX.

[@eeatsvaz]

You had me at merch. 👕

[@DustinWoloschuk]

Aawesome video as always dude!!!!! I've been following along and using all your tips on my AX24 Love the look of it with those tall wheels... they give it insane clearance...lol Thank you!!!!

[@payneja]

Thanks for the build video! I bought the same system and the motor hits the front drive shaft during full compression. There is a perfect groove around the drive shaft where it is rubbing. Also, with the broken hardware..I have had great luck with the Engineer PZ-57 Screw pliers. Grips the cap and shaft of M1.4 hardware with ease.

[@kez850]

What did you come up with to correct the rubbing issue?

[@payneja]

@@kez850 new chassis with more shock location options. The angry sparrow or mofo rc are suitable options.

[@kez850]

@@payneja sweet. I ended up getting the carbon fiber blades from mofo rc which also gives more shock mounting options

[@scotty2hottie324]

Thank you so much for the detailed swap. You answered the one question I didn't understand of which was this system uses stock receiver. So I guess you could use any receiver with this system.

[@2fmrc]

Yep! I usually pull the stock stuff and use a micro receiver for my gt5. Works great!

[@swampfox984]

@@2fmrc What micro reciever do you use for the gt5? I lost my controller that came with the car and the gt5 was the same price as a replacement so I got it instead not realizing that it won't link to the original ESC. I am considering getting this motor kit as well but I want to make sure I can actually pair the gt5 with it.