FUTABA Instructional Videos - How To Register Sensors

[@coreyperez13]

Excellent information. I'm working to install telemetry sensors on a Futaba 14SG and this was very helpful.

[@radiocontrolshop]

Hi Corey, thank you for your encouragement. we are glad our video helped with your setup.

[@mikecomeaux7603]

Do you provide a video on how to set up a cortex gyro for stabilized flight and hold??

[@marcobuonavita2757]

molto molto utile questo video grazie

[@michaelhazard-n2r]

Hello Ronald can you explane how to register a DLPH-1 to a 18SZ thank you

[@ImAcoastpedder]

Nice video. Does anyone know if these sensors can handle 8.4V ? I have a Futaba 4PM, R324SBS and I'm wanting to use my 8.4V capable steering servo at 8.4V. I have 3 Futaba Sensors but don't know if it'll fry them. Futaba is possibly the worst ever with answering questions. Thanks.

[@Statek63]

Great video! Do you know if - when you want to add a new type of telemetry device - then does the transmitter have to support this specific telemetry sensor type in the transmitter software ? So for example if I have a Castle Creations telemetry interface for Futaba and the newest 16IZ Super transmitter (not 16IZ) then does the transmitter software have to support this specific sensor ? Same for any other 3rd party telemetry sensor - does the tranmitter need to "know" this sensor type or does it read it's details from the sensor during registration ? Not sure if my question is clear...

[@BenErikNess]

Please show how you set up the altimeter and vario for a glider!

[@LoetWakkerman]

Is the sensor registered for a particular receiver or to all receivers of the same kind? Thanks

[@robertjones1855]

Do you have to do this with a SBS-02G GPS Sensor ?

[@andyMSH700]

nothing works with telemetry on my T18mz....i think my tx must be faulty. i have had nothing but faults with my t18mz...two batteries failing and telemetry never worked....i am now changing over to radiomaster.

[@mohdhafis9555]

very good information

[@radiocontrolshop]

Thank you for your kind words of encouragement. Look forward to more informative videos!

[@PaulreynoldsMCMXXLII]

Thank you very much for this recording, why don't Futaba do this? Anyway very useful. I now need to set up the sound and voice notifications, do you have an recordings on that?😀

[@radiocontrolshop]

Hi Paul, we discussed a little about the speech option in this video. Have a look! kzbin.info/www/bejne/nYayonduZ72Jbac

[@Good1vibes]

Greetings from SoCal. I’ve been flying RTF helicopters from OMP M1 and M2. I finally got myself a Futaba T16IZ. Any chance of you setting up a Futaba with a Helicopter kit such as SAB or an Align?

[@radiocontrolshop]

Hi, at the moment, the setup is for glider. We take note of this request and could set it as a roadmap for later videos. Thank you for your comments.

[@scalebuilder_sweden]

Thanks for sharing, ✨👍🏻

[@wizardz7938]

Can you do gyro 553 setup on a 553 pleaseeeeee

[@mithrandir1313]

I think you can plug all the sensors into the hub, plug the hub into the "Y" (for the battery) and register all the sensors at the same time...

[@VashStepler]

Hi! For Futaba S.Bus / S.Bus2 receivers. Do I need an S.Bus hub if I am only using a single Telemetry Sensor (ei. 1x Altitude sensor)? Can I plug the sensor directly to an S.Bus / S.Bus2 port?

[@rccosplay3249]

Yes sensor can plug directly into Sbus2 if using only one sensor! If more than one then need a y cable.or hub.

[@SuperRafaelalvarez]

Futaba 16iz problem: the letters on the panel are erased very easily. big futaba mistake