FX Impact valve stem, hammer and valve adjuster reassembly key note.

[@mundoacuatico16]

Le hago una pregunta tengo una fx impact calibre 30 pero cuando disparo sale un poquito de aire por donde esta el magazin. Le cambien os oring de afuera y el interno del cañón pero sigue sali3ndo aire no se si sera la pieza que empuja el diablo en la recámara que no lo cuadre bien . Cual seria la distancia exacta para el calibre 30 de esta pieza usted mide y sale en 91.62 no se si sera para el calibre 30

[@pepesempire]

hi mr Rowe..what size oring are inside the those bushes?

[@paulojrr1]

very nice whats Aluminiun Alloy do tou use in the body of FX' is 6061 T6 or 7075 T6 or another Alloys

[@weeper99167]

please could you make a video on how to easily replace the breech seal. thanks for your videos.

[@ptescreen18]

Is that a sub 12 valve stem ??????? Is there any difference in length between fac and sub12 valve stem I am having issues

[@chuckward9793]

Older video but great info. I took mine apart today. I was not getting the fps I thought I should and found the end of the hammer rod that hits the rubber stop was backed off by at least 4 rounds. Mine has 2 holes but no set screw so I used blue loctite and will test it tomorrow when it is set up good. Is this a common problem? I also added 2 washer spacers in the hammer for more spring pressure. Anything above 135 bar would not change fps. I also increased the TP and matched the probe to it.

[@truescotsman4103]

I just did my valve pin replacement. Mine wasn't that secure but there was a little loctite in there. I put more in there. Getting all the grease off the threads is important so the loctite can do its job. There is no set screw on mine and all of the videos I've seen don't show one used. I see guys using the holes to remove it. They also show using a torch to loosen the loctite but I didn't need to to that just get two sets of padded pliers and break it loose. Blue loctite doesn't hold very well it just keeps it from creeping and coming loose.

[@rockabichebel]

Hello mr how are you plz i wanna ask you about the Vulcan 6.35 using mk2 jdb 34 grain what maximum speed i can get with best accuracy?

[@seanclayton8928]

Hi Ernest I am having issues with my FX GLADIATOR MK11 once cocked it will not fire air. Tanks are full. Any ideas ?? Cheers Sean

[@johnowers47]

Hi, Have you tested for the maximum energy in each calibre of the Impact? I am trying to find out what energy it produces in .22? Thanks

[@ernestrowe5061]

over 54fpe with 34g JSB

[@johnowers47]

Did you open the barrel port to get this power?

[@ernestrowe5061]

barrel port slightly enlarge, angle ported to TP after valve seat, barrel has a high polish, hammer polish, valve rod has a high polish, with a 23.25" barrel got 60fpe. a stronger HS is needed if reg above 165b, must have 3 more spring washer to get higher reg pres.

[@johnowers47]

In .22???

[@mohammedsaleh2192]

I learn from you allot. Your are good. Big thanks to you. I wish you all of the best.

[@4450OhDeere]

Thank you for the video. I had the problem that I couldn’t get my valve knob all in. So I found that end loose when I removed my valve knob . And I can’t see any 1 mm set screw there . Any advice ?

[@truescotsman4103]

There is no set screw that I'm aware of. I have the same gun I just did my valve pin. The hole might be threaded but all of the maintenance videos I've seen don't have a set screw they just use loctite.

[@airrifleshooter.516]

Hi my m3 had a leak and I fixed it but now the speed went down. I took off the rubber ball that goes in the valve spring and the speed came up again. Without the rubber ball do I damage the valve rod or not ? Thanks in advance much appreciated. Keep it up .

[@andrepaio7751]

Another great one! Thanks.

[@willanchen673]

Hammer inside the black is what role

[@ernestrowe5061]

2 open the valve. and controlled by the VS limiter and power wheel

[@azycray4801]

Esting, I love your video's but everything is always apart when they start. I need to see how you disassemble the main sections and then reassemble. The video's cover the repair or servicing of the separate parts but on several I need to know how you got to where you are when the video begins. I can probably figure it out but I would rather learn from someone who has already figured it out. I am having my first major issue with my Impact and I just can't see shipping the whole thing back to the seller and shipping back to me with the time and money involved even if it is still covered under warranty. I would rather just fix it myself. So a video that shows the disassembly of the major parts or sections would greatly appreciated. Then I can watch the specific video for the problem I might be having. One more thing, other than o-rings that can be found easily, how do you get other parts if needed?

[@ernestrowe5061]

DID you see the ---->FX impact .30 action disassembly part 1 & 2 ?

[@azycray4801]

Thank you, I did find those after I commented. I was going to come and remove my question but you had already responded. Thanks again for your great detailed videos!

[@airpower-tr]

you are the best!! thanks

[@penghobykaliber45]

Good job master

[@edosancl]

Thanks!

[@chriswooten7]

6:38 He laughs JUST LIKE Butt-Head!!!!! Check it out lol

[@ShayanQuanta]

complicated mechanism !!

[@АндрейЛомтев-к1б]

you must be a clever man to make so complicated and stuped valve system, weapon even air gun must be simple and reliable like AK47

[@jackclarke7584]

can send you a private email please ?