FX WC power wheel pre-load adjustment screw

[@antonio999us]

Hello Ernest…greetings from Peru 👋👋👋 ….this was a simplest video, but with an extraordinary explanation how to do the right adjustment to the Hammer spring…thanks a lot for your tips…

[@derrickmitchell39dm]

This is the tutorial I been waiting on. Thank you Ernest😀👍. Will you do one on tuning it too?

[@franciscocarvalho2424]

Sempre dando um pouco do seu conhecimento nós é ó esporte agradecemos like sucesso continue

[@AffordableAirguns]

Great info Ernest. Thanks

[@user-hx2cm5ge1q]

Those FX guns could be a dream and a nightmare for a tinkerer like me. Look at all those grub screws lol. So complex they need to make them more simple.

[@larrycoleman2225]

Loving these WC MKIII videos. Keep them coming. Especially on tuning and these disassembly vids so we can add aftermarket goodies, correctly. ;)

[@farooqjamatee]

You are best

[@wellsgb1957]

Thank you👍🏻

[@joseorts3233]

good morning friend, do you have any video with the performance of the wildcat mk3, autonomy, maximum speed, precision etc etc, thanks

[@MikeS1944]

How far in should the Hammer Spring Adjuster go once you get to 7?

[@magwarblood]

Could you do a video on tuning the MK2 wildcat please

[@1234586217]

Hola muy buenas!! Muy buen trabajo sus videos. Muchas gracias. Tengo la fx wildcat mk3 sniper cl 5,5. Y me gustaría saber cual sería la velocidad idónea para tirar los jsb heavy de 18 grains

[@sabadotarde4]

A mi me van bien alrededor de 270m/s

[@timbfoto5823]

My FX wildcat .25 came to me shooting at 888., according to the test card from Air guns of Utah. I bought a crony and the gun is shooting 745. I adjusted the hammer clock wise and now I am shooting 763. My reg is at 148-150. AIR guns of Utah said the reg was to high for .25 ??????? I have watch your tune video 10 times. I would like to shoot 33.4 grain pellets or slugs. What can be done? Thanks Tim

[@timbfoto5823]

@ALAN BRAY no not shooting to it’s potential. Fully charged and reg 148 or 150

[@fincaalcanara]

How do you do this on the FX Maverick….. because you cannot see the hammer spring adjuster like you can in the WCat?

[@palmspar]

When you increase the reg pressure you must find the max pellet speed for that pressure. Left Turn the pre-load adjustment screw until the pellet dont go harder, let say 285ms. Go 3 or 5% under that speed +-275ms by clockwise turning the pre-load adjustment screw, then you dont waste air en blow the pellet out of control

[@havattarah]

@@palmspar did that but now on PW7 the rifle does not engage . the cocking lever does not lock in position I cannot go more they maybe a full turn on the screw in order to prevent that, and with regs 160ish/125 bar I am shooting even less speed (around 780ft/s) then with factury reg pressure - 140/100 bar shooting 930 ft/s JSB 18gr any ideas ? tks

[@svrfx3573]

@@havattarahI’m in the same boat I raised my reg pressure to start shooting slugs kept adjusting hammer spring until the gun would no longer cycle a round before that I could only get up to 950 and I’m told I need to get to 1000 fps, not sure how I get there

[@havattarah]

@@svrfx3573 I cant remember exactly what I did to correct that in that occasion, sorry. but what I have learn having the maverick is that it is a balance between the Pressure and the Hammer. Start on low levels and go by increasing the reg pressure a bit and then little by little the hammer (small increases makes a big difference), then repeat until you get what you want or max out. Also there are different hammer weights on those guns, I had to buy a heavier hummer to get those speeds, my gun was shipped with the lighter of the hammers that they produce. apparently there are 3 (or 4?!) different hammer weights for those guns. The barrel size will also affect your max speeds that you can achieve. The heavier the hammer, the bigger the barrel and the more pressure on the reg, theoretically the higher speeds you will get. but again it will be a balance. Hope it helps... those FX guns are fantastic guns but they can be a bit frustrating to regulate at the beginning.

[@Nico-Max63]

Hi from France , how millimeters we can adjust ( maximum ) ? Thanks

[@mullervolker9814]

Send more DL in F-Series to Germany sooon!!!!! Thanks :/

[@Mike-yq6jg]

Is this the same for the maverick?

[@ernestrowe5061]

Yes

[@lordbanks3140]

@@ernestrowe5061 fx maveric is a powerfeel tightly against the frame and the hammer is not visible ....