Freaking Love the berserk references. And. The soundtrack
@norincokid2 жыл бұрын
Looks good! I have a similar setup for Parkerizing smaller stuff, a two-burner hotplate and a used restaurant stainless third pan. Looks like "my little meth lab" but works pretty well!
@provenancemachining2 жыл бұрын
Good poor-man's solution. I like to use Mark Lee's Express and have some 44/40 on the side in case I need to touch things up. I also like to use a spray bottle as opposed to a brush in order to get the tight spots. If you have any sandblasting capabilities, a trick you could use is dialing down the PSI to something incredibly low like 60-70 depending on how thick the rust is and "blast" the receiver to quickly card off the rust, you need to be careful doing it that way, but it's an easy way to card the inside without having to jam a fine dremel wheel or a chunk of steel wool.
@jojomasterson48522 жыл бұрын
I might try that spray bottle solution in the future, that might be a little faster than using the brushing the solution on.
@Brandon_obs_ls Жыл бұрын
@@jojomasterson4852how dose it hold up to scratches
@joecoastie99 Жыл бұрын
For a better end run finish paint that with used motor oil that has no detergents in it. It will give you a much richer blue. Then you can use a preservative oil.
@michaelpopov15485 ай бұрын
Well explained and very good job! Thank you very much!
@jamesgravel7755 Жыл бұрын
I’ve never tried this technique. Cool vid. I may try this on a project. My best bluing to date was with a product called wonder blue. And it came out really nice after I figured out the proper way to do it. The directions weren’t exactly Correct. But one I got it. Came out great. I would suggest trying. But I will be trying this method soon. Thanks for the info.
@archangel20031 Жыл бұрын
Parkerizing was easier because you only clean it, then boil it once, rinse and oil it.
@Troubledboy884 ай бұрын
I like the $Boys beats in the background!
@RonPieper612 ай бұрын
Nice, thanks.
@martino72632 жыл бұрын
Love the Berserk soundtrack in the background
@worldtraveler930 Жыл бұрын
Not here, I found all the Moaning and Caterwalling in the background rather distracting!!! 🤠👍
@ray_notes8170 Жыл бұрын
How resilient is this coating? Does it last under use or wear off quickly?
@EUROWORKS2 жыл бұрын
Loved the video!!! Keep it up
@johnhall84557 ай бұрын
Couldn’t stay awake…💤💤
@jsharp1776 Жыл бұрын
Where are you purchasing your lowers?
@derekhawkins72907 ай бұрын
Can you please tell me......do you know what you are doing ...........????
@UFPTX6 ай бұрын
I have doubts.
@wecsogarmory94052 жыл бұрын
👍
@sgt_malice4521 Жыл бұрын
what’s your rust solution?
@ray_notes8170 Жыл бұрын
He used hydrogen peroxide and salt. Some add a tiny bit of vinegar as well. 4 part peroxide, 1 part vinegar, 1/3 part salt. I've also seen people super saturate with salt, which I think increases the risk of pitting since any salt not removed from the carding will continue to rust the metal.
@IkramNiazi-om3nx5 ай бұрын
Good vedio nice Info,, but plz never put cartoons in guns vedio my eyes are hurting
@aarontaylor1484 Жыл бұрын
Not bad decrease and keep applying till itbwont turn red anymore.....but inreally don't think the east countries did it much differently
@patrickkelly7838 Жыл бұрын
Your screwy moving backdrop makes me dizzy. It is also very distracting, I would loose it.